IEC 60384-14:2023 applies to capacitors and resistor-capacitor combinations intended to be connected to AC mains or other supply with a nominal voltage not exceeding 1 000 V AC (RMS), and with a nominal frequency not exceeding 100 Hz. This document includes also additional specific conditions and requirements for the connection to DC supplies with a rated voltage not exceeding 1 500 V DC. The principal object of this part of IEC 60384 is to prescribe preferred ratings and characteristics and to select, from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance level; lower performance levels are not permitted. This document also provides a schedule of safety tests to be used by national testing stations in countries where approval by such stations is required. The overvoltage categories in combination with the AC mains voltages for the capacitors classified in this document are to be taken from IEC 60664-1. This edition includes the following significant technical changes with respect to the previous edition:
in damp heat steady state test, all capacitor types are tested both with and without rated voltage; the number of test pieces has been increased;
tangent of loss angle is added In Group 0 tests, in safety tests only;
qualification approval based on safety and performance tests has been removed from the main text to a normative annex;
the range of rated voltages is given instead of exact rated voltage values;
normative annex for description of capacitor styles and of creepage/clearance distance measurement has been added;
the importance of mechanical failures (cracks) in component encapsulation as a safety feature is highlighted in handling instructions and requirements after all relevant tests.

  • Standard
    9 pages
    English and French language
    sale 15% off

IEC 60384-8:2024 is applicable to fixed capacitors of ceramic dielectric with a defined temperature coefficient (dielectric Class 1), intended for use in electronic equipment, including leadless capacitors but excluding fixed surface mount multilayer capacitors of ceramic dielectric, which are covered by IEC 60384-21 (Class 1). Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60384-1:2021, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this document provide specific test severities and requirements of an equal or higher performance level. Further information on the conception of generic, sectional and detail specifications can be found in the Introduction of IEC 60384-1:2021.
This edition includes the following significant technical changes with respect to the previous edition:
a) The document has been completely restructured to comply with ISO/IEC Directives, Part 2 and to make it more useable; tables, figures and references have been revised accordingly. Annex X contains all cross-references of changes in clause/subclause numbers.
b) The terms have been replaced by the letter symbols in Table 3.
c) Code of temperature coefficient and tolerance of C0G, U2J have been added in Table 4, Table 6, Table 8, Table 9, Table 11, Table 13, Table 16 and Annex B.
d) Annex B has been changed from informative to normative.
e) Clause C.5 (Test schedule for quality conformance inspection) has been newly added to withdraw the blank detail specification: IEC 60384-8-1.

  • Standard
    161 pages
    English language
    sale 15% off
  • Standard
    104 pages
    English and French language
    sale 15% off

IEC 60384-9:2024 is applicable to fixed capacitors of ceramic dielectric with a defined temperature coefficient (dielectric Class 2), intended for use in electronic equipment, including leadless capacitors but excluding fixed surface mount multilayer capacitors of ceramic dielectric, which are covered by IEC 60384-22 (Class 2). Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this document provide specific test severities and requirements of an equal or higher performance level. Further information on the conception of generic, sectional and detail specifications can be found in the Introduction of IEC 60384-1:2021.
This edition includes the following significant technical changes with respect to the previous edition:
a) The document has been completely restructured to comply with ISO/IEC Directives, Part 2 and to make it more useable; tables, figures and references have been revised accordingly. Annex X contains all cross-references of changes in clause/subclause numbers.
b) The requirements of reference temperature 25 °C have been added in Table 7, Table 9, Table 11, Table 13 and Table 15.
c) The table of temperature characteristics of capacitance for the reference temperature 25 °C have been added in Table B.1, Table B.2 and Table B.3.
d) Annex B has been changed from informative to normative.
e) Clause C.5 (Test schedule for quality conformance inspection) has been newly added to withdraw the blank detail specification: IEC 60384-9-1.

  • Standard
    139 pages
    English language
    sale 15% off
  • Standard
    90 pages
    English and French language
    sale 15% off

IEC 60384-22:2024 is applicable to fixed unencapsulated surface mount multilayer capacitors of ceramic dielectric, Class 2, for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted on printed boards, or directly onto substrates for hybrid circuits.
Capacitors for electromagnetic interference suppression are not included but are covered by IEC 60384-14. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification provide specific test severities and requirements of an equal or higher performance level. Further information on the conception of generic, sectional and detail specifications can be found in the Introduction of IEC 60384-1:2021.
This edition includes the following significant technical changes with respect to the previous edition:
a) The document has been completely restructured to comply with the ISO/IEC Directives, Part 2 and to make it more useable; tables, figures and references have been revised accordingly.
b) The requirements of reference temperature 25 °C has been added in Table 5, Table 9, Table 10, Table 12, Table 14 and Table 17.
c) The table of temperature characteristics of capacitance for the reference temperature 25 °C have been added in Table C.1, Table C.2 and Table C.3.
d) The requirement in 5.5.2 (visual examination) has been repeated in 5.9.3, 5.10.6, 5.11.4, 5.12.6, 5.13.8, 5.14.6 and 5.15.6.
e) The deflection D in the very robust designs has been added in 5.9.1.
f) Annex C has been changed informative into normative.
g) Clause D.5 (Test schedule for quality conformance inspection) has been newly added to withdraw the blank detail specification: IEC 60384-22-1.

  • Standard
    167 pages
    English language
    sale 15% off
  • Standard
    107 pages
    English and French language
    sale 15% off

IEC 60384-21:2024 is applicable to fixed unencapsulated surface mount multilayer capacitors of ceramic dielectric with a defined temperature coefficient (dielectric Class 1), intended for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted on printed boards, or directly onto substrates for hybrid circuits. Capacitors for electromagnetic interference suppression are not included but are covered by IEC 60384-14. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification provide specific test severities and requirements of an equal or higher performance level. Further information on the conception of generic, sectional and detail specifications can be found in the Introduction of IEC 60384-1:2021.
This edition includes the following significant technical changes with respect to the previous edition:
a) the document has been completely restructured to comply with the ISO/IEC Directives, Part 2 and to make it more useable; tables, figures and references have been revised accordingly; Annex X contains all cross-references of changes in clause/subclause numbers;
b) the terms have been replaced by the letter symbols in Table 3;
c) code of temperature coefficient and tolerance of C0G, U2J have been added in Table 4, Table 6, Table 8, Table 9, Table 11, Table 13, Table 16 and Annex B;
d) the requirement in 5.5.2(visual examination) has been repeated in 5.9.3, 5.10.5, 5.11.4, 5.11.4, 5.13.7, 5.14.5 and 5.15.5;
e) the deflection D in the very robust designs has been added in 5.9.1;
f) Annex B has been changed informative into normative;
g) Clause C.5 (Test schedule for quality conformance inspection) has been newly added to withdraw the blank detail specification: IEC 60384-21-1.

  • Standard
    147 pages
    English language
    sale 15% off
  • Standard
    94 pages
    English and French language
    sale 15% off

IEC TS 63337:2024 provides requirements, test conditions and tests to validate characteristics including the service life of customized DC-link film capacitors for use in motor vehicle components.
Standard DC-link capacitors qualified according to other IEC standards or AEC-Q200 are excluded from the scope of this document.
The requirements, test conditions and tests listed in this document apply to customized film capacitors developed for use in motor vehicle power electronics for the application as a DC-link capacitor in HV applications or in the intermediate circuit of the 48 V on-board electrical system.
These qualification requirements can be expanded or adapted for the application of technologically innovative designs, if necessary. The content and scope of supplements is therefore to be specified and documented in coordination between the responsible parties prior to sourcing.
Power electronics in the motor vehicle need to be tested in accordance with the environmental qualification standards of the vehicle manufacturers.
The tests in this document do not replace the tests specified in the Component Requirement Specifications for complete vehicle components or additional or deviating further requirements, test conditions and tests described therein.
This document contains no tests to validate the thermal interface between capacitors, power electronics and the cooling system on the component level.

  • Technical specification
    38 pages
    English language
    sale 15% off

IEC 60939-3:2024 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this document. This document applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this document will either be connected to mains supplies, when compliance with the mandatory tests of Table B.1 is necessary, or used in other circuit positions where the equipment specification specifies that some or all of these safety tests are required. This document applies to passive filter units, which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC, with a nominal frequency not exceeding 400 Hz, or 1 500 V DC. Note: For AC use, IEC 60384-14 applies to capacitors which will be connected to AC mains with a nominal frequency not exceeding 100 Hz. This document covers appliance filters (US) but does not cover facility filters, cord-connected filters or direct plug-in filters. These other filters will be covered by another sectional specification.
This edition includes the following significant technical changes with respect to the previous edition:
a) separated clauses for safety and performance tests;
b) added note for use of multiple X capacitors bridging basic insulation in 3 phase filters;
c) characteristics and conditions to substitute X and Y capacitors are now described in a separate Subclause 4.1;
d) creepage and clearance tables updated and in line with the latest editions of IEC 60938-2 and IEC 60664-1;
e) allowing voltage measurement for inductance measurements (7.3);
f) added requirements for marking depending on remaining energy after disconnection;
g) added content of CTL DSH 2044:2016 for temperature test of IEC filters;
h) added note about temperature rise required specimens for safety testing;
i) changed index of capacitors in Annex A to avoid confusion between index name and capacitor class;
j) moved tests from group 1A to 2. Now, samples in group 1A need to be submitted without potting;
k) revision of all parts of the document has taken place based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents. Annex X contains all cross-references of changes in clause/subclause numbers.

  • Standard
    251 pages
    English language
    sale 15% off
  • Standard
    162 pages
    English and French language
    sale 15% off

IEC 60115-4-10:2023(E) is applicable to the drafting of detail specifications for fixed power resistors with leads, classified to level G, which is defined in IEC 60115‑1:2020, 3.4 for general electronic equipment. It is a supplementary document to the sectional specification and contains requirements for style, layout and minimum contents of detail specifications.

  • Standard
    47 pages
    English language
    sale 15% off

IEC 60938-2-1:2023 is applicable to the drafting of detail specifications for fixed inductors for which safety tests are required for use in electronic equipment.
A blank detail specification is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements shall not be considered as being in accordance with IEC specifications nor shall they so be described.
This edition includes the following significant technical changes with respect to the previous edition:
a) it combines IEC 60938-2-1:1999 and IEC 60938-2-2:1999 into one Blank detail specification (BDS);
b) test schedule for quality conformance inspection is moved to an informative annex (Annex B).

  • Standard
    34 pages
    English and French language
    sale 15% off

IEC TS 60286-6-1:2023 specifies a bulk case capable of containing miniaturized surface mount components of sizes within the range of 0402M to 1005M (see Table 1 for explanation of the codes). The bulk case is designed for transport and storage of components and to supply of components directly or by an appropriate feeder to the placement machine. The bulk case is equipped with a coupling interface to enable its automatic handling, e.g. by a robot or automatic handling machines.

  • Technical specification
    14 pages
    English language
    sale 15% off

IEC 60393-4:2023 is applicable to single-turn rotary power potentiometers wire-wound technology. Enamelled, cemented, moulded, enclosed.
This specification is applicable to rotary potentiometers with nominal dissipation in excess of 10 W, the resistive element of which consists of a wire or a wound tape. All the potentiometers specified by this specification are slider-driven without reduction. Their stroke less than 360° is limited by stops.
This document specifies preferred ratings and characteristics and selects from IEC 60393-1, appropriate quality assessment procedures, tests and measuring methods. It provides general performance requirements for this type of potentiometer.
This document gives the minimum performance requirements and test severities. Annex A lists the letters and symbols used in the clauses of this document.
This edition includes the following significant technical changes with respect to the previous edition:
a) the document structure has been organized to follow new sectional specification structure decided in TC 40;
b) the information on the assessment level EZ and FZ (zero nonconforming) has been revised.

  • Standard
    63 pages
    English and French language
    sale 15% off

IEC 60115-8:2023 is applicable to fixed surface mount resistors for use in electronic equipment. These resistors are typically described according to types (different geometric shapes) and styles (different dimensions) and product technology. These resistors have metallized terminations and are primarily intended to be mounted directly onto a circuit board.
The object of this document is to specify preferred ratings and characteristics and to select from IEC 60115-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor.
This edition includes the following significant technical changes with respect to the previous edition:
a) definitions of product technologies and product classification levels of the generic specification, IEC 60115-1:2020, have been adopted;
b) new style of transverse (RT) resistors has been added in 3.1.5 and 4.2.2 to cover resistors with wide terminals, which have become common in market;
c) recommended test boards in 5.2.2 have been revised to fit the demands from the market for higher rated dissipation in resistors;
d) test boards have been revised so that they can be set vertically instead of horizontally during specified tests to optimize the temperature rise stability, area and spacing inside the test chamber;
e) 'Periodic-pulse high-voltage overload test' of IEC 60115‑1:2020, 8.3 has been added to the default test method in 5.3.8, however, the legacy test 'periodic-pulse overload test' of IEC 60115‑1:2020, 8.4 is still maintained for historical products;
and more. Please see the foreword for the list of changes.

  • Standard
    214 pages
    English and French language
    sale 15% off

IEC 60393-3:2023 applies to rotary precision potentiometers for use in electronic equipment. The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60393-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of potentiometer. This document gives the minimum performance requirements and test severities.
This edition includes the following significant technical changes with respect to the previous edition:
a) revised all parts of the document based on the ISO/IEC Directives, Part 2:2018 (eighth edition) and harmonized with other similar kinds of documents;
b) the document structure has been organized to follow new sectional specification structure decided in TC 40;
c) revision of the information on the assessment level EZ (zero nonconforming).

  • Standard
    69 pages
    English and French language
    sale 15% off

IEC 60939-2:2005 applies to passive filter units for electromagnetic interference suppression which fall within the scope of the Generic Specification IEC 60939-1. The scope of this Sectional specification is restricted to passive filter units for which safety tests are appropriate. This implies that filters specified according to this Sectional specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 3 is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. The contents of the corrigendum of November 2005 have been included in this copy.

  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    88 pages
    English and French language
    sale 15% off
  • Standard
    183 pages
    English and French language
    sale 15% off

IEC 60115-2:2023 is applicable to fixed low-power film resistors with termination leads for use in electronic equipment, which are typically assembled in through-hole technology (THT) on circuit boards.
These resistors are typically described according to types (different geometric shapes) and styles (different dimensions) and product technology. The resistive element of these resistors is typically protected by a conformal lacquer coating. These resistors have wire terminations and are primarily intended to be mounted on a circuit board in through-hole technique.
The object of this document is to state preferred ratings and characteristics and to select from IEC 60115-1 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor.
This edition includes the following significant technical changes with respect to the previous edition:
the definitions of product technologies and product classification levels of the generic specification, IEC 60115‑1:2020, have been adopted;
the preferred dimensions given in Table 1 have been reviewed, and the legacy style RA_0922 has been removed;
a basis for the optional specification of the lead eccentricity of axial leaded resistors has been amended in 4.2;
the 'period-pulse high-voltage overload test' of IEC 60115‑1:2020, 8.3 has been adopted as default test method in 5.3.8, thereby replacing the legacy test 'periodic-pulse overload test' of IEC 60115‑1:2020, 8.4;
the revised solderability test of IEC 60115‑1:2020, 11.1 has been adopted in 5.3.19 and 5.3.20;
the combined solvent resistance test of IEC 60115‑1:2020, 11.3 has been adopted in 5.3.22;
the 'endurance at room temperature test' of IEC 60115‑1:2020, 7.2 (prior IEC 60115 2:2014, Annex C) has been adopted as an optional test in 5.4.1;
the 'single-pulse high-voltage overload test' of IEC 60115 1:2020, 8.2, applied with the pulse shape 10/700 in 5.3.7, is complemented with the optional alternative provided by the pulse shape 1,2/50 in 5.4.2;
climatic tests for 'operation at low temperature' of IEC 60115‑1:2020, 10.2, and for 'damp heat, steady state, accelerated' of IEC 60115‑1:2020, 10.5, have been adopted as optional tests in 5.4.4 and 5.4.5, respectively;
new guidance is provided in 6.2 on the presentation of stability requirements with their permissible absolute and relative deviations;
acceptance criteria for the visual examination have been added in 6.5 and in Annex B;
visual examination for the primary and proximity packaging has been added in 6.5.2 and in 7.2;
the periodical evaluation of termination platings has been added as a new topic of quality assessment in 9.8;
the revised test clause numbering of IEC 60115‑1:2020 has been applied;
a new Annex C has been added to summarize workmanship requirements for the assembly of leaded film resistors, e.g. as given in the prior IEC 61192 series of standards;
the informative Annex F (prior Annex B) on radial formed styles has been amended with details on a formed Z-bend style for surface-mount assembly.

  • Standard
    95 pages
    English language
    sale 15% off

IEC 60115-2-10:2023 is a detail specification which specifies the characteristics and ratings of low-power film resistors with leads for use in electronic equipment, which are typically assembled in through-hole technology (THT) on circuit boards. This detail specification establishes test schedules and performance requirements permitting the quality assessment of the resistors covered herein according to the quality assessment procedures specified by IEC 60115-1:2020, Annex Q.
This first edition cancels and replaces IEC 60115-2-1:1982. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
it employs the product classification based on application requirements as defined in the generic specification IEC 60115‑1:2020;
it permits the specification of additional dimensional requirements concerning the eccentricity of termination wires and the coating extending onto wires;
it provides for a tabulated presentation of resistance ranges in relationship to the temperature coefficient and the tolerance;
it supports solderability testing for both traditional lead-bearing soldering and up-to-date lead-free soldering, as required;
it introduces a test for the specimens’ robustness to electrostatic discharge;
it introduces a test for the specimens’ resistance to solvents;
it introduces a test for the flammability of the specimens;
it employs consistent stability requirements grouped in stability classes;
it supports the provision of detailed visual acceptance criteria;
it includes the requirement for a visual examination of the primary and proximity packaging;
it provides the correlated test schedules for a qualification approval and for subsequent quality conformance inspections side by side;
it employs quality assessment procedures which meet the requirements of a zero-defect approach, which evades the use of historic AQL levels and the permission of non-conforming specimens in test groups;
it provides for the inclusion of specific visual acceptance criteria, to be applied in addition to those given in Annex B of the sectional specification IEC 60115-2:2023;
it provides for the optional coverage of 0 Ω resistors (jumpers) within the scope of the drafted detail specification;
furthermore, it employs a new document structure, for which a transition guidance is provided in Annex X.

  • Standard
    46 pages
    English language
    sale 15% off

IEC 60384-20:2023 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyphenylene sulfide dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. This part of IEC 60384 specifies preferred ratings and characteristics and selects from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level; lower performance levels are not permitted. Capacitors for electromagnetic interference suppression are not included but are covered by IEC 60384‑14. This edition includes the following significant technical changes with respect to the previous edition:
- revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents;
- the document structure has been organized to follow new sectional specification structure decided in TC 40;
- revised tables and Clause 5 so as to prevent duplications and contradictions;
- in Clause 5.2 (Mounting), the Subclauses 5.2.1, 5.2.2 and 5.2.3 have been added;
- in Subclause 5.5 (Shear test), the Subclauses 5.5.1 and 5.5.2 have been added;
- in Subclause 5.14 (Component solvent resistance), the Subclauses 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 (Final inspections and requirements) in Group 1A and in Subgroup C1;
- in Subclause 5.15 (Solvent resistance of marking), the Subclauses 5.15.1 and 5.15.2 have been added;
- tangent of loss angle measurement has been added to resistance to soldering heat test;
- lot-by-lot and periodical inspection tables, including requirements, have been moved to Annex A;
- revised Inspection Level (IL) of A1 subgroup.

  • Standard
    122 pages
    English language
    sale 15% off
  • Standard
    76 pages
    English and French language
    sale 15% off

IEC 60384-23:2023 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyethylene naphthalate dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. This part of IEC 60384 specifies preferred ratings and characteristics, selects from IEC 60384‑1:2021 the appropriate quality assessment procedures, tests and measuring methods and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384‑14. This edition includes the following significant technical changes with respect to the previous edition:
- this edition includes the following significant technical changes with respect to the previous edition: revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents;
- the document structure has been organized to follow new sectional specification structure decided in TC 40;
- revised tables and Clause 5 so as to prevent duplications and contradictions;
- in Subclause 5.2 (Mounting), the Subclauses 5.2.1, 5.2.2 and 5.2.3 have been added;
- in Subclause 5.5 (Shear test), the Subclauses 5.5.1 and 5.5.2 have been added;
- in Subclause 5.14 (Component solvent resistance), the Subclauses 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 (Final inspections and requirements) in Group 1A and in Subgroup C1;
- in Subclause 5.15 (Solvent resistance of marking), the Subclauses 5.15.1 and 5.15.2 have been added;
- tangent of loss angle measurement has been added to the resistance to soldering heat test;
- lot-by-lot and periodical inspection tables including requirements have been moved to Annex A;
- revised Inspection Level (IL) of A1 subgroup.

  • Standard
    122 pages
    English language
    sale 15% off
  • Standard
    76 pages
    English and French language
    sale 15% off

IEC 60384-14:2023 applies to capacitors and resistor-capacitor combinations intended to be connected to AC mains or other supply with a nominal voltage not exceeding 1 000 V AC (RMS), and with a nominal frequency not exceeding 100 Hz. This document includes also additional specific conditions and requirements for the connection to DC supplies with a rated voltage not exceeding 1 500 V DC. The principal object of this part of IEC 60384 is to prescribe preferred ratings and characteristics and to select, from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance level; lower performance levels are not permitted. This document also provides a schedule of safety tests to be used by national testing stations in countries where approval by such stations is required. The overvoltage categories in combination with the AC mains voltages for the capacitors classified in this document are to be taken from IEC 60664-1. This edition includes the following significant technical changes with respect to the previous edition:
in damp heat steady state test, all capacitor types are tested both with and without rated voltage; the number of test pieces has been increased;
tangent of loss angle is added In Group 0 tests, in safety tests only;
qualification approval based on safety and performance tests has been removed from the main text to a normative annex;
the range of rated voltages is given instead of exact rated voltage values;
normative annex for description of capacitor styles and of creepage/clearance distance measurement has been added;
the importance of mechanical failures (cracks) in component encapsulation as a safety feature is highlighted in handling instructions and requirements after all relevant tests.
The content of the corrigendum 1 (2024-10) has been included in this copy.

  • Standard
    274 pages
    English language
    sale 15% off
  • Standard
    180 pages
    English and French language
    sale 15% off

IEC 60539-1:2022 is applicable to directly heated negative temperature coefficient thermistors, typically made from transition metal oxide materials with semiconducting properties.
It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
This edition includes the following significant technical changes with respect to the previous edition:  
Restructured completely to comply to ISO/IEC directives; categorization and reorganization of test methods into these categories;
Annex X added for comparison to the previous edition;
Some wordings, figures and references have been revised.

  • Standard
    139 pages
    English and French language
    sale 15% off

IEC 60115-4:2022 relates to resistors having a rated dissipation typically greater than 1 W up to and including 1 000 W for use in electronic equipment. This document is applicable to fixed power resistors with a maximum surface temperature (MET) higher than the preferred upper category temperature (UCT) of 200 °C.
NOTE Heat sink resistors, i.e. resistors which in their operation depend on being mounted on a dedicated heat sink, owing to their special temperature conditions, are covered by a special sectional specification (under consideration at the time of publication).
These resistors are typically described according to types (different geometric shapes) and styles (different dimensions), and product technology.
The object of this document is to define preferred ratings and characteristics and to select from IEC 60115-1 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of resistor.
NOTE SMD resistors are covered by IEC 60115-8, regardless of their dissipation.
This edition includes the following significant technical changes with respect to the previous edition:
the definitions of product technologies and product classification levels of the generic specification, IEC 60115-1:2020, have been adopted;
a basis for the optional specification of the lead eccentricity of axial leaded resistors has been amended in 4.2;
the 'period-pulse high-voltage overload test' of IEC 60115-1:2020, 8.3 has been adopted as default test method in 5.3.9, thereby replacing the legacy test 'periodic-pulse overload test of IEC 60115-1:2020, 8.4;
the revised solderability test of IEC 60115-1:2020, 11.1 has been adopted in 5.3.22 and 5.3.23;
the combined solvent resistance test of IEC 60115-1:2020, 11.3 has been adopted in 5.3.25;
the 'endurance at room temperature test' of IEC 60115-1:2020, 7.2 has been reworked and adopted in 5.3.5;
the 'single-pulse high-voltage overload test' of IEC 60115-1:2020, 8.2, applied with the pulse shape 10/700 in 5.3.8, is complemented with the optional alternative provided by the pulse shape 1,2/50 in 5.4.1.
climatic tests for 'operation at low temperature' of IEC 60115 1:2020, 10.2, and for 'damp heat, steady state, accelerated' of IEC 60115‑1:2020, 10.5, have been adopted as optional tests in 5.4.5. and 5.4.6, respectively;
inclusion of an optional flammability test as 5.4.8;
new guidance is provided in 6.2 on the presentation of stability requirements with their permissible absolute and relative deviations;
acceptance criteria for the visual inspection have been added in 6.5 and in Annex B;
visual inspection for the primary and proximity packaging has been added in 6.5.3 and in 7.2;
the periodical evaluation of termination platings has been added as a new topic of quality assessment in 9.8;
the revised test clause numbering of IEC 60115-1:2020 has been applied;
a new Annex C has been added to summarize workmanship requirements for the assembly of leaded power resistors, e.g. as given in the prior IEC 61192 series of standards;
the informative Annex F on radial formed styles has been amended with details on a formed Z-bend style for surface-mount assembly;
furthermore, the informative Annex X has been ad

  • Standard
    113 pages
    English language
    sale 15% off

IEC 60286-3:2022 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This document also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips). This edition includes the following significant technical changes with respect to the previous edition:  
addition terms and definitions.
addition of a table of the classification to symbols concerning drive hole diameter and distance between the reel hole centre and the drive hole centre;
addition of drive hole to the reel (optional);
revision of reel hole diameter tolerances;
revision of 72 mm tape size carrier tape width dimension tolerances;
addition of Annex B (informative);
addition of component size 0201M.

  • Standard
    170 pages
    English language
    sale 15% off
  • Standard
    113 pages
    English and French language
    sale 15% off

IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads.
It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes.
This edition includes the following significant technical changes with respect to the previous edition:
a) complete revision of structure;
b) consolidation of essential parameters and requirements in Clause 4.

  • Standard
    70 pages
    English and French language
    sale 15% off

IEC 62391-1:2022 applies to fixed electric double-layer capacitors (hereafter referred to as capacitors) mainly used in DC circuits of electric and electronic equipment.
This part of IEC 62391 establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
This edition includes the following significant technical changes with respect to the previous edition:
The document has been completely restructured to comply with the ISO/IEC Directives, Part 2; a new technical categorization of test methods has been introduced and the test methods have been reorganized according to these new categories; tables, figures and references have been revised accordingly.
Calculation formula of charging/discharging efficiency in Annex D were divided into two cases: "Calculation assuming full charge and discharge" and "Calculation assuming incomplete charging and discharging due to internal resistance".

  • Standard
    125 pages
    English and French language
    sale 15% off

IEC 60738-1:2022 describes terms and methods of test for positive step-function temperature coefficient thermistors, insulated and non-insulated types, typically made from ferro-electric semi-conductor materials.
It establishes standard terms, inspection procedures and methods of test for use in detail specifications for qualification approval and for quality assessment systems for electronic components.
This edition includes the following significant technical changes with respect to the previous edition:
a) Restructured completely to comply with ISO/IEC Directives; categorization and reorganization of test methods into these categories;
b) Some wordings, figures and references have been revised.

  • Standard
    132 pages
    English and French language
    sale 15% off

IEC 60384-1-1:2022 establishes a generic template and specifies requirements to the content of detail specifications for capacitors within the IEC 60384-X series. This part of IEC 60384-1 is applicable to the drafting of detail specifications for fixed capacitors for use in electronic equipment.

  • Standard
    41 pages
    English and French language
    sale 15% off

IEC 60384-19:2022 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage.
This part of IEC 60384 specifies preferred ratings and characteristics, and selects from IEC 60384‑1:2021 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted.
Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384‑14.
This edition includes the following significant technical changes with respect to the previous edition:  
revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents;
the document structure has been organized to follow new sectional specification structure decided in TC 40;
revised tables and Clause 5 to prevent duplications and contradictions;
in Clause 5.2 (Mounting), 5.2.1, 5.2.2 and 5.2.3 have been added;
in Clause 5.5 (Shear test), 5.5.1 and 5.5.2 have been added;
in Clause 5.14 (Component solvent resistance), 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 Final inspections in Group 1A and in Subgroup C1;
in Clause 5.15 (Solvent resistance of marking), 5.15.1 and 5.15.2 have been added;
tangent of loss angle measurement has been added to resistance to soldering heat test;
lot-by-lot and periodical inspection tables including requirements have been moved to Annex A;
revised Inspection Level (IL) of A1 subgroup.

  • Standard
    76 pages
    English and French language
    sale 15% off

IEC TR 63362-1:2022(E) establishes guidelines for the application and use of aluminium electrolytic capacitors in electronic equipment.
The information given in this document applies to capacitors with non-solid electrolyte but can, in its appropriate clauses, apply to capacitors with solid electrolyte as well.
Electrolytic capacitors in general – and aluminium electrolytic capacitors in particular – are an exception in the capacitor field because of the components’ close interaction of physics and chemistry. Therefore, aluminium electrolytic capacitors show, in various aspects, a technical behaviour unaccustomed to the user. That could easily lead to misapplications and even to endangering of persons and goods. The aim of this document is to minimize these risks by providing detailed information on the specific peculiarities of the component.
This first edition cancels and replaces CLC/TR 50454 published in 2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
Complete technical revision, details of cleaning processes and failure modes added.
Inclusion of parts of JEITA RCR 2367D.

  • Technical report
    26 pages
    English language
    sale 15% off

IEC 61051-2:2021 is a sectional specification and is applicable to metal oxide varistors with symmetrical voltage-current characteristics for use in electronic equipment connected to any AC or DC supply system.
These varistors are designed to protect electronic and other sensitive equipment from high transient surges. Varistors under the scope of this sectional specification are not intended to give primary protection against lightning surges.
These varistors have metallic connections and are intended to be mounted as through hole component or directly on to printed boards.
The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 61051-1 the appropriate quality assessment procedures, tests and measuring methods, and to give general performance requirements for this type of varistors.
This edition includes the following significant technical changes with respect to the previous edition:  
revision for the structure in accordance with ISO/IEC Directives, Part 2) to the extent practicable, and for harmonizing with IEC 61051-1:2018;
Annex X has been added for comparison with the previous edition;
two lists of preferred voltage ratings for disk type and SMD type varistors have been added;
permissible numbers of non-conforming items have been set to zero (zero fault) in the test schedule in 8.4.3.

  • Standard
    42 pages
    English and French language
    sale 15% off

IEC TR 60286-3-4:2021(E) considers the proposed requirements for emboss taping for the Auto Loading Feeder mechanism to mount electric components without leads or with stump type leads used for electric circuits. This document is applicable to the embossed carrier tape, with single round sprocket holes, with tape pitches of 2 mm or more (nominal tape width: 8 mm only) among the tapes of Type 2a in IEC 60286-3.
The contents of the corrigendum of June 2022 have been included in this copy.

  • Technical report
    26 pages
    English language
    sale 15% off

IEC TR 60286-3-3:2021(E) describes the possible requirements for paper taping for the Auto Loading Feeder mechanism to mount electronic components without leads or with stump type leads used for electric circuits. This document is applicable to the punched carrier tape with the bottom cover tape (nominal tape width: 8 mm only) among the tapes of Type 1a, and the pressed carrier tape (nominal tape width: 8 mm) of Type 1b in IEC 60286-3.

  • Technical report
    22 pages
    English language
    sale 15% off

IEC 60938-2:2021 applies to fixed inductors designed for electromagnetic interference suppression, which will be connected to an AC mains or other supply with a nominal voltage not exceeding 1 000 V AC RMS or 1 500 V DC with a nominal frequency not exceeding 400 Hz.
This sectional specification is restricted to fixed inductors for which safety tests are appropriate. This implies that inductors specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Annex A is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required.
The object of this document is to prescribe standard requirements for safety tests, preferred ratings and characteristics, to select from IEC 60938-1 the appropriate methods of test and to give general performance requirements for suppression inductors.
This edition includes the following significant technical changes with respect to the previous edition:
- the test plan for performance testing has been removed; mandatory safety tests and optional performance tests are listed in one test plan in Annex B;
- requirements for Thyristor-Chokes have been withdrawn;
- material requirements are harmonized with IEC 60939-3 and UL 60939-3;
- AC chokes up to 1 000 V and DC chokes up to 1 500 V are now in the Scope.

  • Standard
    70 pages
    English and French language
    sale 15% off

IEC 60384-1:2021 is a generic specification and is applicable to fixed capacitors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
This edition includes the following significant technical changes with respect to the previous edition:
a) The document has been completely restructured to comply with the ISO/IEC Directives, Part 2; a new technical categorization of test methods has been introduced and the test methods have been reorganized according to these new categories; tables, figures and references have been revised accordingly.
b) Annex X has been added for comparison with the previous edition.

  • Standard
    163 pages
    English and French language
    sale 15% off

IEC 60384-25:2021 applies to fixed aluminium electrolytic surface mount capacitors with conductive polymer solid electrolyte, primarily intended for DC applications for use in electronic equipment. The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60384-1:2016, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. This edition includes the following significant technical changes with respect to the previous edition:
- Revision of the structure in accordance with ISO/IEC Directives, Part 2:2018, to the extent practicable, and harmonization between other similar kinds of documents.
- In addition, Clause 5 and all the tables have been reviewed in order to prevent duplications and contradictions.
The contents of the corrigendum of May 2023 have been included in this copy.

  • Standard
    96 pages
    English language
    sale 15% off
  • Standard
    64 pages
    English and French language
    sale 15% off

IEC 60384-24:2021 applies to fixed tantalum electrolytic surface mount capacitors with conductive polymer solid electrolyte, which are primarily intended for DC applications for use in electronic equipment. The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. This edition includes the following significant technical changes with respect to the previous edition: - Revision of the structure in accordance with ISO/IEC Directives, Part 2:2018, to the extent practicable, and harmonization between other similar kinds of documents.
- In addition, Clause 5 and all the tables have been reviewed in order to prevent duplications and contradictions.

  • Standard
    92 pages
    English language
    sale 15% off
  • Standard
    61 pages
    English and French language
    sale 15% off

IEC 60938-1:2021 applies to inductors designed for electromagnetic interference suppression intended for use within all kind of electric and electronic equipment.
In this generic specification, normative references and terms and definitions are given. It also prescribes general requirements and the suitable test and measurement procedures for interference suppression inductors. Annex B states special requirements for earth inductors.
This edition includes the following significant technical changes with respect to the previous edition:
a) material tests added;
b) improved readability and clear separation between test descriptions in the generic spec and requirements in the sectional specification;
c) creepage and clearance requirements are now defined in sectional specifications only;
d) AC testing for voltage test included.

  • Standard
    61 pages
    English and French language
    sale 15% off

IEC 60384-2:2021 applies to fixed capacitors for direct current, with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have a possibility of "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. Two performance grades of capacitors are covered: grade 1 for long-life application and grade 2 for general application.
Capacitors for electromagnetic interference suppression and surface mount fixed metallized polyethylene-terephthalate film dielectric DC capacitors are not included, but are covered by IEC 60384-14 and IEC 60384-19, respectively.
The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring methods, and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance level, because lower performance levels are not permitted.
This edition includes the following significant technical changes with respect to the previous edition:
a) revision of all parts of the document based on the ISO/IEC Directives, Part 2:2018 and harmonization with other similar kinds of documents;
b) the document structure has been organized to follow the new sectional specification structure decided by TC 40;
c) revision of tables and Clause 5 so as to prevent duplications and contradictions.

  • Standard
    32 pages
    English language
    sale 15% off
  • Standard
    64 pages
    English and French language
    sale 15% off

IEC 60286-1:2017 applies to the tape packaging of components with axial leads for use in electronic equipment. In general, the tape is applied to the component leads.
It covers requirements for taping techniques used with equipment for the preforming of leads, automatic handling, insertion and other operations, and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes.
This edition includes the following significant changes with respect to the previous edition:
a) a complete revision of the structure (detailed in Annex A) and reworked layout.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    24 pages
    English and French language
    sale 15% off
  • Standard
    53 pages
    English and French language
    sale 15% off

IEC 60384-13:2020 specifies preferred ratings and characteristics, selects from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted.
This part of IEC 60384 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this document are intended for use in electronic equipment.
Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14.
This edition includes the following significant technical changes with respect to the previous edition:
a) revision of all parts of the document based on the ISO/IEC Directives, Part 2:2018, and harmonization with other similar kinds of documents;
b) the document structure has been organized to follow new sectional specification structure decided in TC 40;
c) revised tables and Clause 5 so as to prevent duplications and contradictions.

  • Standard
    66 pages
    English and French language
    sale 15% off

IEC 60115-1:2020 is a generic specification and is applicable to fixed resistors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
This edition contains the following significant technical changes with respect to the previous edition:
this 5th edition employs a new document structure, where the tests of prior Clause 4 are given in Clauses 6 to 12 now, with an informative Annex X providing cross-references for references to the prior revision of this standard;
the terms and definitions have been revised and amended, supplemented by a new section on resistor technologies and a new section on product classification levels;
a new Subclause 4.7 on recommendations for permissible substitutions has been added;
the provisions for packaging, storage and transportation in Subclauses 4.8, 4.9 and 4.10 have been completely revised;
a new Subclause 5.3 on default tolerances for the most common test parameters has been added;
the generic method of measuring resistance, now Sublause 5.6, has been separated from the test for compliance with a prescribed resistance value in 6.1, as a revision of the prior 4.5;
the test for the temperature coefficient of resistance of Subclause 6.2 is a revision of the prior test 4.8, variation of resistance with temperature, where the special concessions for resistors below 10 Ω have been waived;
the test methods for endurance testing of Subclauses 7.1 to 7.3 (prior 4.25.1 to 4.25.3) have been completely revised;
the single‑pulse high‑voltage overload test of Subclause 8.2 (prior 4.27) has been completely revised, and now offers adjustable severities for the 1,2/50 and for the 10/700 pulse shape for the benefit of detail specifications with improved significance;
the periodic-pulse high-voltage overload test of Subclause 8.3 (prior 4.28) has been revised and a corrected table of severities provided;
the period-pulse overload test of Subclause 8.4 (prior 4.39) has been deprecated and streamlined to only offer the severity historically applied in subordinate specifications;
the Subclauses 9.1 on visual inspection, 9.2 on the gauging of dimensions, and 9.3 on the assessment of detail dimensions (all parts of prior 4.4) have been completely revised;
the tests for robustness of terminations (prior 4.16) have been revised and separated into tests for the robustness of solderable terminations, Subclause 9.5, and tests for the robustness of threaded stud or screw terminations, Subclause 9.6;
the bump test of Subclause 9.9 (prior 4.20) and the shock test of Subclause 9.10 (prior 4.21) have been revised to reflect the merged relevant test standard IEC 60068-2-29;
the dry heat and cold test of the climatic sequence of Subclause 10.3 (prior 4.23) have been revised to reflect the changes of the relevant test standards IEC 60068‑2‑2 and IEC 60068‑2‑1;
the accelerated damp heat, steady state test of Subclause 10.5 (prior 4.37) has been amended with an option for a reduced number of bias voltages;
the corrosion test of Subclause 10.6 has been completely revised in order to employ the better suitable test method of IEC 60068-2-52 instead of the prior used IEC 60068-2-11;
the whisker growth test of Subclause 10.7 has been revised to reflect the changes of the new revision of the test methods of IEC 60068-2-82;
the test methods for solderability of Subclause 11.1 (prior 4.17) and for resistance to soldering heat of Subclause 11.2 (prior 4.18) have been completely revised to incorporate the necessary option for the variety of lead-bearing and lead-free solder alloys and respective process conditions;
the solvent resistance test of Subclause 11.3 combines the prior tests 4.29, component solvent resistance, and 4.30, solvent resistance of marking, in one test;
the accidental overload test of Subclause 12.3 (prior 4.26) has been completely r

  • Standard
    322 pages
    English and French language
    sale 15% off

IEC TR 60286-7:2019 contains information about the introduction of an innovative bulk blister packing system for miniaturized components, for example chip type components of size 1005 (metric) and smaller. It includes a proposal for standardization of the interface between the packaging and automatic assembly systems and requirements to the properties of the packaging.

  • Technical report
    24 pages
    English and French language
    sale 15% off