59 - TEXTILE AND LEATHER TECHNOLOGY
ICS 59 Details
TEXTILE AND LEATHER TECHNOLOGY
TEXTIL- UND LEDERINDUSTRIE
INDUSTRIE TEXTILE ET TECHNOLOGIE DU CUIR
TEKSTILNA IN USNJARSKA TEHNOLOGIJA
General Information
Frequently Asked Questions
ICS 59 is a classification code in the International Classification for Standards (ICS) system. It covers "TEXTILE AND LEATHER TECHNOLOGY". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 6965 standards classified under ICS 59 (TEXTILE AND LEATHER TECHNOLOGY). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
e-Library Subscription
Create subscription and get permanent access to documents within 59 - TEXTILE AND LEATHER TECHNOLOGY
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
ISO 10580:2010 specifies a general laboratory test method for determination of the area-specific emission rate of volatile organic compounds (VOC) and/or the vapour-phase VOC concentration under defined climate conditions.
ISO 10580:2010 describes emission test chambers used for the determination of the emission of volatile organic compounds from resilient, textile and laminate floor coverings.
- Standard29 pagesEnglish languagee-Library read for1 day
This document specifies the method for determination of the elongation under load and the residual deformation of coated fabrics.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
This document specifies the following for raw bovine hides and skins intended for use throughout the leather manufacturing supply chain:
— Terms and definitions;
— Requirements for the presentation of raw hides and skins.
It is applicable to fresh and salted bovine hides and skins.
It outlines the opening cut and trim of hides and skins and the types of defects typically associated with this raw material.
NOTE 1 Opening cut and trim vary from country to country.
It shows which parts of hides and skins can be used for leather production and which factors influence the quality of hides and skins.
Furthermore, it gives recommendations on precautions to be taken for transport, preservation, loading and unloading.
NOTE 2 For commercial agreements between the buyer and the supplier of hides and skins, operators use the INTERNATIONAL CONTRACT No. 6 – HIDES and SKINS as drawn up by the International Council of Hides, Skins and Leather Traders Associations (ICHSLTA) and the International Council of Tanners (ICT) [1].
- Standard19 pagesEnglish languagee-Library read for1 day
This document sets the minimum essential elements of traceability and evidence of verification to be present in a leather traceability system, kept by organizations along the animal-to-leather supply chain. It is applicable to all types of leather.
This document defines the requirements and related evidence for establishing the traceability of leather back to the originating farms or hunting area.
This document can be applied to any organization operating within the leather value chain.
- Standard14 pagesEnglish languagee-Library read for1 day
This document specifies guidelines for grading raw sheep skins on the basis of their mass and size.
- Standard2 pagesEnglish languagesale 15% off
This document specifies the following for raw bovine hides and skins intended for use throughout the leather manufacturing supply chain:
— Terms and definitions;
— Requirements for the presentation of raw hides and skins.
It is applicable to fresh and salted bovine hides and skins.
It outlines the opening cut and trim of hides and skins and the types of defects typically associated with this raw material.
NOTE 1 Opening cut and trim vary from country to country.
It shows which parts of hides and skins can be used for leather production and which factors influence the quality of hides and skins.
Furthermore, it gives recommendations on precautions to be taken for transport, preservation, loading and unloading.
NOTE 2 For commercial agreements between the buyer and the supplier of hides and skins, operators use the INTERNATIONAL CONTRACT No. 6 – HIDES and SKINS as drawn up by the International Council of Hides, Skins and Leather Traders Associations (ICHSLTA) and the International Council of Tanners (ICT) [1].
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the index ingredient of chemicals in coloured textile dyed with gallnut. Gallnut can be applied to both natural fibre and manufactured fibre.
- Standard5 pagesEnglish languagesale 15% off
This document sets the minimum essential elements of traceability and evidence of verification to be present in a leather traceability system, kept by organizations along the animal-to-leather supply chain. It is applicable to all types of leather.
This document defines the requirements and related evidence for establishing the traceability of leather back to the originating farms or hunting area.
This document can be applied to any organization operating within the leather value chain.
- Standard14 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the resistance of all forms of leather to visible soiling through repeated contact with soiled objects. It provides a physical pretreatment routine for leathers that can be vulnerable to loss of soiling resistance while in service, prior to conducting further tests such as cleaning.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies the performance requirements and test methods for filtration property and safety of materials for nonwoven general use face coverings for single use. This document specifies the following filtration properties: sub-micron filtration efficiency (PFE), water aerosol filtration efficiency with bacteria (BFE), water aerosol filtration efficiency with viruses (VFE), pollen particle filtration efficiency, and differential pressure. This document specifies the following safety items: free formaldehyde, specific azo dye, heavy metals, and pH. This document applies to nonwoven general use face coverings. It does not apply to medical face masks (see EN 14683 [5]), medical devices, or personal protective equipment (PPE) in the scope of ISO/TC94/SC15, Respiratory protective devices (RPD).
- Standard31 pagesEnglish languagesale 15% off
This document specifies a test method for the determination of heating performance of wearable heating e-textile products. Wearable heating textile products are made of e-textile parts including a portable battery for electric heating and conventional textile parts for garments. This document includes the test procedure for the heating temperature and power consumption of wearable heating garments such as jackets, vests, etc. Heating gloves and footwear are excluded. The safety and security of heating products are excluded, as the information on thermal safety limits for heating products is addressed in IEC 60335-2-17 [1] 1 and IEC 62368-1 [2]. The performance and safety of the portable battery are also excluded.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the resistance of all forms of leather to visible soiling through repeated contact with soiled objects. It provides a physical pretreatment routine for leathers that can be vulnerable to loss of soiling resistance while in service, prior to conducting further tests such as cleaning.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of heating performance of wearable heating e-textile products. Wearable heating textile products are made of e-textile parts including a portable battery for electric heating and conventional textile parts for garments. This document includes the test procedure for the heating temperature and power consumption of wearable heating garments such as jackets, vests, etc. Heating gloves and footwear are excluded. The safety and security of heating products are excluded, as the information on thermal safety limits for heating products is addressed in IEC 60335-2-17 [1] 1 and IEC 62368-1 [2]. The performance and safety of the portable battery are also excluded.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the resistance of all forms of leather to visible soiling through repeated contact with soiled objects. It provides a physical pretreatment routine for leathers that can be vulnerable to loss of soiling resistance while in service, prior to conducting further tests such as cleaning.
- Standard8 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
This document lists circular economy principles and provides guidance for circular economy across the textile value chain and value network and circularity for textile products.
This document applies to textiles, textile products, including non-textile components and materials.
This document excludes leather, fur products and footwear.
- Technical specification39 pagesEnglish languagee-Library read for1 day
This document lists circular economy principles and provides guidance for circular economy across the textile value chain and value network and circularity for textile products.
This document applies to textiles, textile products, including non-textile components and materials.
This document excludes leather, fur products and footwear.
- Technical specification39 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the resistance of the colour of textiles of all kinds and in all forms to ironing and to processing on hot cylinders.
This document is applicable for hot pressing when the textile is dry, damp or wet which is determined by the end-use of the textile.
- Standard12 pagesEnglish languagee-Library read for1 day
This document specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions (single braid, double braid and multi-core construction) for general purpose made of high modulus polyethylene (HMPE), and gives rules for their designation.
Many different types and grades of HMPE fibre exist which are commonly used to produce rope products. This document does not apply to all variations in strength or product performance.
- Standard14 pagesEnglish languagee-Library read for1 day
This document specifies a method for the determination of the composition of feather and/or down fit for or constituting filled manufactured articles in order to label and/or mark it or to verify the denominations reported on the label.
- Standard12 pagesEnglish languagee-Library read for1 day
This document specifies a method of testing the adsorption efficiency of activated carbon fibres, such as nonwoven fabric or fibrous felt with a thickness of less than 20 mm for adsorption and removal of iodine isotopes (I131), included in air or gas flow (exhaust).
- Standard19 pagesEnglish languagesale 15% off
This document specifies a method for the determination of the composition of feather and/or down fit for or constituting filled manufactured articles in order to label and/or mark it or to verify the denominations reported on the label.
- Standard12 pagesEnglish languagee-Library read for1 day
This document provides information on the design of geosynthetics for surface erosion control on slopes and river or channel banks. It does not apply to the design of geosynthetics for the stability of slopes and river or channel banks. It does not apply to coastal protection issues.
- Technical report55 pagesEnglish languagesale 15% off
This document specifies a method for determining the resistance of the colour of textiles of all kinds and in all forms to ironing and to processing on hot cylinders.
This document is applicable for hot pressing when the textile is dry, damp or wet which is determined by the end-use of the textile.
- Standard12 pagesEnglish languagee-Library read for1 day
This document specifies a method for the measurement of flame spread times of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich combinations, and similar combinations) when subjected to a small, defined flame.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies a method for the measurement of ease of ignition of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich constructions, and similar combinations), when subjected to a small, defined flame.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
The test is normally carried out on dry specimens conditioned in the specified atmosphere.
The test is applicable to most types of geosynthetic products, but does not apply to products with apertures greater than 10 mm.
- Standard13 pagesEnglish languagee-Library read for1 day
This document specifies methods for the measurement of the thermal resistance and water-vapour resistance , under steady-state conditions, of e.g. fabrics, films, coatings, foams and leather, including multilayer assemblies, for use in clothing, quilts, sleeping bags, upholstery and similar textile or textile-like products.
The application of this measurement technique is restricted to a maximum thermal resistance and water-vapour resistance which depend on the dimensions and construction of the apparatus used (e.g. 2 m2·K/W and 700 m2·Pa/W respectively, for the minimum specifications of the equipment referred to in this document).
The test conditions used in this document are not intended to represent specific comfort situations, and performance specifications in relation to physiological comfort are not stated.
- Standard25 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the resistance of the colour of textiles of all kinds and in all forms to ironing and to processing on hot cylinders. This document is applicable for hot pressing when the textile is dry, damp or wet which is determined by the end-use of the textile.
- Standard5 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
This document specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions (single braid, double braid and multi-core construction) for general purpose made of high modulus polyethylene (HMPE), and gives rules for their designation.
Many different types and grades of HMPE fibre exist which are commonly used to produce rope products. This document does not apply to all variations in strength or product performance.
- Standard14 pagesEnglish languagee-Library read for1 day
This document gives guidelines to select the test methods to assess the performance of leather for automotive. This document also specifies the sampling and conditioning procedures of specimens.
NOTE Regulations on chemical substances in consumer goods might differ from country to country requiring
for any given market a special attention to restricted substances.
- Standard11 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of total amount of halogens (including fluorine, chlorine, bromine and iodine) present in textile products by combustion and ion chromatography (C-IC).
This document is applicable to all materials of textile products which are combustible, e.g. fibres, fabrics, plastic components (including coating), wood.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies the main characteristics and test methods of new fibre ropes used for offshore station keeping. Fibre ropes for stationkeeping can be manufactured from different rope materials. This document provides general requirements applicable to all types of ropemaking materials. The subsequent parts of the ISO 18692 series provide the specific requirements for each rope core material (as quoted in the title of each part) that are not addressed within this document.
- Standard45 pagesEnglish languagesale 15% off
- Standard47 pagesFrench languagesale 15% off
This document establishes a designation system of recycled carbon fibres, which can be used as the basis for specification. This designation system is applicable to recycled carbon fibres used for polymer composites. The types of recycled carbon fibres are differentiated by a designation system based on appropriate levels of the designatory properties: tensile modulus of elasticity. tensile strength. NOTE One to five designatory property(s) that differentiate recycled carbon fibre types from each other is (are) assigned.
- Standard8 pagesEnglish languagesale 15% off
This document specifies a test method for the determination of heating performance of wearable heating e-textile products. Wearable heating textile products are made of e-textile parts including a portable battery for electric heating and conventional textile parts for garments. This document includes the test procedure for the heating temperature and power consumption of wearable heating garments such as jackets, vests, etc. Heating gloves and footwear are excluded. The safety and security of heating products are excluded, as the information on thermal safety limits for heating products is addressed in IEC 60335-2-17 and IEC 62368‑1. The performance and safety of the portable battery are also excluded.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions (single braid, double braid and multi-core construction) for general purpose made of high modulus polyethylene (HMPE), and gives rules for their designation. Many different types and grades of HMPE fibre exist which are commonly used to produce rope products. This document does not apply to all variations in strength or product performance.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
IEC 63517:2026 specifies a test method for the determination of heating performance of wearable heating e-textile products. Wearable heating textile products are made of e-textile parts including a portable battery for electric heating and conventional textile parts for garments. This document includes the test procedure for the heating temperature and power consumption of wearable heating garments such as jackets, vests, etc. Heating gloves and footwear are excluded. The safety and security of heating products are excluded, as the information on thermal safety limits for heating products is addressed in IEC 60335-2-17 and IEC 62368‑1. The performance and safety of the portable battery are also excluded.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
This document specifies methods for the measurement of the thermal resistance and water-vapour resistance , under steady-state conditions, of e.g. fabrics, films, coatings, foams and leather, including multilayer assemblies, for use in clothing, quilts, sleeping bags, upholstery and similar textile or textile-like products.
The application of this measurement technique is restricted to a maximum thermal resistance and water-vapour resistance which depend on the dimensions and construction of the apparatus used (e.g. 2 m2·K/W and 700 m2·Pa/W respectively, for the minimum specifications of the equipment referred to in this document).
The test conditions used in this document are not intended to represent specific comfort situations, and performance specifications in relation to physiological comfort are not stated.
- Standard25 pagesEnglish languagee-Library read for1 day
This document specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. NOTE Such coatings are known as poly(vinyl chloride) (PVC) coatings. This document is applicable to two grades (A and B) of PVC-coated woven fabrics.
- Standard9 pagesEnglish languagesale 15% off
This document gives guidelines to select the test methods to assess the performance of leather for automotive. This document also specifies the sampling and conditioning procedures of specimens.
NOTE Regulations on chemical substances in consumer goods might differ from country to country requiring
for any given market a special attention to restricted substances.
- Standard11 pagesEnglish languagee-Library read for1 day
This document specifies methods for the measurement of the thermal resistance and water-vapour resistance , under steady-state conditions, of e.g. fabrics, films, coatings, foams and leather, including multilayer assemblies, for use in clothing, quilts, sleeping bags, upholstery and similar textile or textile-like products. The application of this measurement technique is restricted to a maximum thermal resistance and water-vapour resistance which depend on the dimensions and construction of the apparatus used (e.g. 2 m2·K/W and 700 m2·Pa/W respectively, for the minimum specifications of the equipment referred to in this document). The test conditions used in this document are not intended to represent specific comfort situations, and performance specifications in relation to physiological comfort are not stated.
- Standard17 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
This document specifies the digital measurement method for the determination of the anti-contamination of fabrics. This method is applicable to woven fabrics which have or have not been given an anti-contamination to particulate matter finish. It is especially suitable for measuring apparel fabrics. It is not intended for use in fabrics that react to UV light or allow particulate matter to penetrate into the structure of the fabric. It is not applied to fabrics for personal protective equipment. NOTE 1 Particulate matter (PM) is solid particles suspended in ambient air defined in ISO 16890-1. NOTE 2 In woven fabrics, particulate matter (PM) adheres to the fabric surface due to electrostatic or surface properties. In knitted and nonwoven fabrics, PM penetrates into the fabric structure, following a different mechanism. The conditions and procedures outlined in this test method are designed to ensure reproducibility and precision specifically when applied to woven fabrics.
- Standard8 pagesEnglish languagesale 15% off
This document specifies methods for the determination of seam maximum force of sewn seams when the force is applied perpendicularly to the seam. It describes the method known as the grab test.
The method defined in this document is applicable to woven textile fabrics, including fabrics which exhibit stretch characteristics imparted by the presence of an elastomeric fibre, mechanical or chemical treatment. It can be applicable to fabrics produced by other techniques. It is normally not applicable to geotextiles, nonwovens, coated fabrics, textile-glass woven fabrics and fabrics made from carbon fibres or polyolefin tape yarns.[2], [3], [4]
This method is applicable to straight seams only (obtained from previously sewn articles or prepared from fabric samples) and not to curved seams (see Annex B for considerations on seams).
The method is restricted to the use of constant-rate-of-extension (CRE) testing machines.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
The test is normally carried out on dry specimens conditioned in the specified atmosphere.
The test is applicable to most types of geosynthetic products, but does not apply to products with apertures greater than 10 mm.
- Standard13 pagesEnglish languagee-Library read for1 day
This document specifies a method for determining the total content (solvent extractable) of melamine in chemicals for the leather tanning industry.
This method requires the use of liquid chromatography (LC) with a triple quadrupole mass spectrometer (MS/MS), an ultraviolet (UV) detector, or diode array detector (DAD) to identify and quantify the melamine.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies a method for the measurement of ease of ignition of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich constructions, and similar combinations), when subjected to a small, defined flame.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies a method for the measurement of flame spread times of vertically oriented textile fabrics and industrial products in the form of single or multi-component textile fabrics (coated, quilted, multilayered, sandwich combinations, and similar combinations) when subjected to a small, defined flame.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies a method to test filtration performance of particulate matter of nonwovens. This document is applicable to nonwovens for air filtration.
- Standard10 pagesEnglish languagesale 15% off
This document defines the term nonwovens and provides auxiliary terminology to distinguish nonwovens from other materials.
- Standard11 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of total amount of halogens (including fluorine, chlorine, bromine and iodine) present in textile products by combustion and ion chromatography (C-IC).
This document is applicable to all materials of textile products which are combustible, e.g. fibres, fabrics, plastic components (including coating), wood.
- Standard19 pagesEnglish languagee-Library read for1 day