ISO/TC 17/SC 19 - Technical delivery conditions for steel tubes for pressure purposes
Maintenance of existing ISO Standards and preparation of new ISO Standards for technical delivery conditions for steel tubes for pressure purposes, in liaison with ISO/TC 5 and ISO/TC 11. Excluded from this area of work are all other standards for tubes whatever their use and particularly the standards related to ISO/TC 67 and the standards on tubes for transportation of water, gas and sewage.
Conditions techniques de livraison des tubes d'acier pour appareils à pression
Maintenance des normes ISO existantes et élaboration de nouvelles normes ISO concernant les conditions techniques de livraison des tubes d'acier pour appareils à pression, en liaison avec l'ISO/TC 5 et l'ISO/TC 11. Sont exclues toutes les autres normes relatives aux tubes, quel que soit leur usage, en particulier les normes liées à l'ISO/TC 67, et les normes relatives aux tubes destinés au transport de l'eau, du gaz et des eaux usées.
General Information
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
This document specifies an employer's qualification system for non-destructive testing (NDT) personnel performing the testing of the following steel products under the employer's responsibility: a) tubes/pipes (seamless or welded); b) flat products, long products, rails, bars, sections, rods and wires. This document specifies qualification requirements for the competence of Level 1 and Level 2 NDT personnel to execute specific tasks in the NDT of steel products. The qualification is issued by the employer for a specific steel product and a specific test method. This document is applicable to NDT personnel performing predominantly the automated testing of steel products, using any of the following NDT methods: a) eddy current testing (ET); b) leak testing (LT); c) liquid penetrant testing (PT); d) magnetic testing (MT); e) radiographic testing (RT); f) ultrasonic testing (UT); g) visual testing (VT).
- Standard19 pagesEnglish languagesale 15% off
This document specifies the requirements for digital radiographic X-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDAs) of the longitudinal or helical weld seams of automatic fusion arc-welded steel tubes for the detection of imperfections. This document specifies acceptance levels and calibration procedures. It can also be applicable to the testing of circular hollow sections. NOTE As an alternative, see ISO 10893-6 for film-based radiographic X-ray testing.
- Standard18 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
This document specifies requirements for film-based radiographic X-ray testing of the longitudinal or helical weld seams of automated fusion arc-welded steel tubes for the detection of imperfections. It can also be applicable to the testing of circular hollow sections. NOTE As an alternative, see ISO 10893-7 for digital radiographic testing.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
ISO 10893-12:2011 specifies requirements for the automated full peripheral ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc-welded (SAW) tubes, for wall thickness measurement. It specifies the testing method and corresponding calibration procedures. It can also be applicable to the testing of circular hollow sections. ISO 10893-12:2011 is applicable to the thickness measurement of tubes with a specified outside diameter equal to or greater than 25,4 mm and a minimum wall thickness of 2,6 mm, unless otherwise agreed on.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
ISO 10893-10:2011 specifies requirements for automated full peripheral ultrasonic shear wave (generated by conventional or phased array technique) testing of seamless and welded [except submerged arc-welded (SAW)] steel tubes, for the detection of longitudinal and/or transverse imperfections. In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer. For seamless tubes, by agreement between the purchaser and manufacturer, testing principles of ISO 10893-10:2011 can be applied to detect imperfections having other orientations. ISO 10893-10:2011 is applicable to the inspection of tubes with an outside diameter greater than or equal to 10 mm, normally with an outside diameter-to-thickness ratio greater than or equal to 5. It can also be applicable to the testing of circular hollow sections.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
ISO 10893-11:2011 specifies requirements for the automated ultrasonic shear wave (generated by conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric resistance and induction-welded (EW) steel tubes. For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by agreement, perpendicular to the weld seam or both. For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam. In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer. ISO 10893-11:2011 can also be applicable to the testing of circular hollow sections.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO 10893-4:2011 specifies requirements applicable to liquid penetrant testing of seamless and welded tubes for the detection of surface imperfections. It is applicable to all or any part of the tube surface as required by the relevant product standards. It can also be applicable to the testing of hollow sections.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
ISO 10893-9:2011 specifies requirements for the automated ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections carried out in the pipe mill before or during pipe production. ISO 10893-9:2011 can also be applicable to the testing of strips/plates used in the manufacture of circular hollow sections.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
ISO 10893-2:2011 specifies requirements for automated eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections according to the different acceptance levels. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm. It can also be applicable to the testing of hollow sections.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
ISO 10893-3:2011 specifies requirements for automated full peripheral magnetic flux leakage testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections. Unless otherwise specified in the purchase order, ISO 10893-3:2010 is applicable to the detection of predominantly longitudinal imperfections. ISO 10893-3:2010 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm. It can also be applicable to the testing of hollow sections.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
ISO 10893-8:2011 specifies requirements for automated ultrasonic testing for the detection of laminar imperfections in the pipe body (full peripheral testing) of seamless and welded, except submerged arc-welded (SAW), steel tubes, or in the area adjacent to the weld seam of welded steel tubes, and, optionally, at the ends (full peripheral testing) of seamless and welded tubes. ISO 10893-8:2011 can also be applicable to the testing of circular hollow sections.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO 10893-5:2011 specifies requirements for magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections on the tube body and the end/bevel face at the ends. For the tube body, it specifies requirements for the detection of surface imperfections on all or part of the outside surface of tubes. However, by agreement between the purchaser and manufacturer, it can be applicable to the inside surface over a limited length from the ends of tubes, dependent on the tube diameter. In addition, ISO 10893-5:2011 can be used, as appropriate, to locate the position of external surface imperfections detected by another non-destructive testing method (e.g. ultrasonic) prior to dressing of the tube surface, and to ensure complete removal of the imperfection after dressing is complete. For the end/bevel face at the ends of plain-end and beveled-end tubes, ISO 10893-5:2010 specifies requirements for the detection of laminar imperfections which can interfere with subsequent fabrication and inspection operations (e.g. welding and ultrasonic inspection of the welds). ISO 10893-5:2011 is applicable to the detection of imperfections, other than laminar imperfections, on the end/bevel face. In this case, magnetization is applied in the direction essentially perpendicular to the orientation of the particular imperfections being detected. It can also be applicable to the testing of hollow sections.
- Standard7 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
ISO 10893-1:2011 specifies requirements for automated electromagnetic testing of seamless and welded steel tubes, with the exception of submerged arc-welded (SAW) tubes, for verification of hydraulic leak-tightness. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm, when testing with eddy current, and greater than 10 mm when testing with flux leakage method. It can also be applicable to the testing of hollow sections.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
ISO 10332:2010 specifies requirements for automated ultrasonic shear-wave (generated by single element probes or the phased-array technique) testing of seamless and welded (except submerged arc-welded) steel tubes, for verification of hydraulic leak-tightness. The testing technique is applied for the detection of predominantly longitudinal imperfections. Where applicable, Lamb-wave testing may be applied at the discretion of the manufacturer. ISO 10332:2010 is applicable to the inspection of tubes with an outside diameter greater than or equal to 10 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5.
- Standard7 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
ISO 10893-13:2007 describes an employer's qualification system for non-destructive testing (NDT) personnel performing the inspection of the following steel products under the employer's responsibility: tubes/pipes (seamless or welded); flat products, long products, rails, bars, sections, rod, wire.
- Draft15 pagesEnglish languagesale 15% off
- Draft15 pagesFrench languagesale 15% off
This part of ISO 9330 specifies the technical delivery conditions for submerged arc-welded tubes of circular crosssection, made of unalloyed or alloyed steel with specified elevated temperature properties. These tubes are intended for pressure purposes in cases when the material is also subjected to elevated temperatures, e.g. for the construction of steam generating equipment and for interconnecting pipework. The requirements of appropriate international application standards and relevant national legal regulations shall be taken into account by the user. For boilers and pressure vessels International Standards ISO 831, ISO 2604 and ISO 5730 are available. For the general technical delivery requirements, see ISO 404. NOTE The English words "tube" and "pipe" are synonymous.
- Standard25 pagesEnglish languagesale 15% off
This part of ISO 9330 specifies the technical delivery conditions for submerged arc-welded tubes of circular crosssection, made of unalloyed or alloyed steel with specified low temperature properties. These tubes are intended for pressure purposes in cases when the material is also used as part of a low temperature piping system. The requirements of appropriate international application standards and relevant national legal regulations shall be taken into account by the user. For pressure-containing equipment International Standard ISO 5730 is available. For the general technical delivery requirements, see ISO 404. NOTE The English words "tube" and "pipe" are synonymous.
- Standard22 pagesEnglish languagesale 15% off
Specifies the technical delivery conditions for electric resistance and induction welded tubes of circular cross-section having a wall thickness up to and including 16 mm. These pipes are intended for low temperature piping systems. For boilers and pressure vessels ISO 5730 is available. Partial revision of ISO 2604-3:1975.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
Specifies the technical delivery conditions for seamless steel tubes of circular cross-section, made of austenitic stainless steel. These tubes are applied at room temperature, at low temperatures or at elevated temperatures and are intended for the construction of pressure vessels, chemical plants and steam generating equipment. Replaces ISO 2604-2:1975.
- Standard26 pagesEnglish languagesale 15% off
- Standard28 pagesFrench languagesale 15% off
- Standard28 pagesFrench languagesale 15% off
Specifies the technical delivery conditions for seamless tubes of circular cross-section with specified elevated temperature properties. These pipes are intended for elevated temperature piping systems. For pressure containing equipment ISO/R 831 and ISO 5730 are available. Replaces ISO 2604-2:1975.
- Standard22 pagesEnglish languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
Contains the technical delivery conditions for logitudinally welded tubes of circular cross-section, made of austenitic stainless steel. These tubes are applied for pressure resisting purposes at room temperature, at low temperatures or at elevated temperatures and are intended for the construction of pressure vessels, chemical plants and steam generating equipment. Partial revision of ISO 2604-5:1978.
- Standard27 pagesEnglish languagesale 15% off
- Standard28 pagesFrench languagesale 15% off
- Standard28 pagesFrench languagesale 15% off
Specifies the technical delivery conditions for seamless tubes of circular cross-section with specified low temperature properties. These pipes are intended for low temperature piping systems. For pressure containing equipment ISO 5730 is available. Replaces ISO 2604-2:1975.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
Specifies the technical delivery conditions for electric resistance and induction welded tubes of circular cross-section having a wall thickness up to and including 16 mm, made of unalloyed and alloyed steels with specified elevated temperature properties. These pipes are intended for the construction of steam generating equipment and for interconnecting pipework. Partial revision of ISO 2604-3:1975.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
Lays down the conditions for tubes of circular cross-section. These tubes are intended for pressure purposes including the transport of fluids under pressure. Includes symbols and denominations, information to be supplied by the purchaser, manufacturing process, metallurgical properties, dimensions, masses and tolerances, appearance and soundness, inspection and testing, marking and protection.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
Applies to seamless steel tubes with circular section of non-alloy quality steel. These tubes are provided for general pressure purposes including transporting of pressurized fluids. There are standards and rules permitting the use of these tubes up to a temperature of 350 0C (see annex A). The terms "tube" and "pipe" are synonymous terms. For general technical delivery conditions see ISO 404.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
Specifies the characteristics of plain end tubes manufactured from unalloyed and alloyed steels (including austenitic stainless steels). It does not apply to steel tubes intended for exposure to flame. An annex gives metric dimensions which correspond to inch dimensions.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
Specifies the characteristics of plain end tubes manufactured from unalloyed and alloyed steels (including austenitic and ferritic stainless steels). It does not apply to steel tubes indended for exposure to flame. An annex gives metric dimensions which correspond to inch dimension.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
ISO 10893-6:2011 specifies requirements for film-based radiographic X-ray testing of the longitudinal or helical weld seams of automated fusion arc-welded steel tubes for the detection of imperfections. It can also be applicable to the testing of circular hollow sections.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
ISO 10893-7:2011 specifies the requirements for digital radiographic X-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDA) of the longitudinal or helical weld seams of automatic fusion arc-welded steel tubes for the detection of imperfections. ISO 10893-7:2011 specifies acceptance levels and calibration procedures. ISO 10893-7:2011 can also be applicable to the testing of circular hollow sections.
- Standard17 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
ISO 11484:2009 describes an employer's qualification system for non-destructive testing (NDT) personnel performing the inspection of the following steel products under the employer's responsibility: tubes/pipes (seamless or welded); flat products, long products, rails, bars, sections, rod, wire.
- Standard15 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
Gives requirements for radiographic testing of the longitudinal or spiral weld seams of submerged arc-welded steel tubes for the detection of imperfections using the X-ray film technique.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
Contains requirements for ultrasonic testing of the area adjacent to the weld seam of welded steel tubes for pressure purposes, for the detection of laminar imperfections. No lower limit to tube thickness is specified.
- Standard4 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
Describes requirements for the ultrasonic testing of strips/plates used in the manufacture of welded tubes for the detection of laminar imperfections according to three different acceptance levels. This inspection shall be carried out in the pipe mill before or during pipe production, in the flat form.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
Refers to liquid penetrant testing of seamless and welded tubes for the detection of surface imperfections, according to four different test categories. May be applied to all or any part of the tube surface as required by the relevant product quality standards.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
Specifies requirements for ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections, according to four different acceptance levels. Covers the inspection of tubes with an outside diameter greater than 30 mm. Does not specify a lower limit of wall thickness.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
Specifies the training, qualification and certification requirements for three levels of NDT personnel competence to execute specific tasks in the NDT of seamless and welded steel tubes, including the weld seam, and flat products used in the manufacture of welded tubes. Applies to the following NDT methods: eddy current, flux leakage, liquid penetrant, magnetic particle, radiographic, ultrasonic.
- Standard15 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
Specifies requirements for electromagnetic testing. The principle of the method is testing using a concentric coil or a rotating tube/pancake coil eddy current technique, or a rotating tube/magnetic transducer flux leakage technique.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
Specifies requirements and a method for ultrasonic testing. Is applicable to the inspection of tubes with an outside diameter greater than or equal to 168,3 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5. By agreement between the purchaser and manufacturer, it can also be applied to smaller tube diameters.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
Specifies general requirements and the requirements with regard to the method of test, reference standards, equipment calibration and checking, acceptance, and test report.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off