SC 34A - Electric light sources

IEC 63356-2:2024 specifies design parameters and design values of an LED light source or related interface characteristics.
NOTE 1 Interface characteristics can cover interfaces between the LED light source and the luminaire or the controlgear, or the LED light source and additional attachments.
NOTE 2 Interfaces can be related to for example electrical, mechanical, or optical aspects.
This document does not cover interchangeability between products from different LED light source manufacturers.
NOTE 3 Interchangeability is covered by IEC 63356-1.
Lamp caps and lampholders specified in the IEC 60061 series are not within the scope of this document. This second edition cancels and replaces the first edition published in 2022. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) a new Clause 6 for circular LED modules with a circular light emitting surface for spot lighting has been added;
b) a new Clause 7 for LEDni modules with a rectangular shape and a circular light emitting surface has been added.

IEC 63013:2017 is applicable to LED packages for general lighting services.
It specifies procedures and conditions for measuring the luminous flux maintenance of LED packages. It also provides the procedures and conditions (criteria) of projecting the long-term luminous flux maintenance based on limited luminous flux maintenance test data collected. Within the context of this document, wherever luminous flux measurement data is specified, radiant flux measurement data can also be used.

IEC 60809:2021 is applicable to electric light sources for use in automotive applications, for example in road illumination devices and/or light signalling devices for road vehicles.
It is especially applicable to light sources listed in UN Resolution R.E.5 and light sources subject to other legislations.
This fourth edition cancels and replaces the third edition published in 2014, Amendment 1:2017, Amendment 2:2017 and Amendment 3:2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Introduction of a light technical measurement on LED light sources intended for use in front-lighting applications.
b) As the original data sheets and some figures from previous editions were not available in an editable format, they have been reproduced from their old format, following the current drafting rules and are now in single language format. Some reproductions constitute minor (obvious) editorial changes of the original text sections and original figures; no technical changes were introduced.

IEC 63356-1:2023 specifies data sheets of LED lamps and LED modules with a series of parameters per data sheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers.
This second edition cancels and replaces the first edition published in 2022. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) addition of datasheets for GH36d capped LED lamps;
b) addition of datasheets for GJ6.6t and GJ6.6d-1 capped LED lamps;
c) addition of datasheets for GR6d capped LED lamps.

IEC 63356-2:2022 specifies design parameters and design values of an LED light source or related interface characteristics.
NOTE 1 Interface characteristics can cover interfaces between the LED light source and the luminaire or the controlgear, or the LED light source and additional attachments.
NOTE 2 Interfaces can be related to for example electrical, mechanical, or optical aspects.
This document does not cover interchangeability between products from different LED light source manufacturers.
NOTE 3 Interchangeability is covered by IEC 63356-1.
Lamp caps and lampholders specified in the IEC 60061 series are not within the scope of this document.

IEC 63356-1:2022 specifies data sheets of LED lamps and LED modules with a series of parameters per data sheet for a specific LED light source that enables interchangeability between products from different LED light source manufacturers.

IEC 632186:2022 specifies the performance requirements of flexible organic light emitting diode tiles and panels for use on supplies up to 120 V ripple free DC for indoor and similar general lighting purposes and designed for being bent during the manufacturing process of curved luminaires.

IEC 60810:2017 is applicable to filament lamps, discharge lamps, LED light sources and LED packages to be used in road vehicles, i.e. in headlamps, fog-lamps, signalling lamps and interior lighting. It is especially applicable to those lamps and light sources which are listed in IEC 60809.
This fifth edition cancels and replaces the fourth edition published in 2014 and Amendment 1:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- update and clarification of the title and scope;
- introduction of new LED light sources;
- introduction of requirements for LED light sources;
- introduction of guidelines on LED package robustness validation for LED packages.

IEC 62868-2-3:2021 specifies the safety requirements for flexible organic light emitting diode tiles and panels for use on supplies up to 120 V ripple free DC for indoor and similar general lighting purposes and designed for being bent during the manufacturing process of curved luminaires.

IEC 62922:2016 specifies the performance requirements of OLED tiles and panels for use on DC supplies up to 120 V or AC supplies up to 50 V at 50 Hz or 60 Hz for indoor and similar general lighting purposes.

IEC 61228:2020 describes the method of measuring, evaluating and specifying the UV irradiation characteristics of fluorescent ultraviolet lamps that are used in appliances for tanning purposes. It includes specific requirements regarding the marking of such lamps. This third edition cancels and replaces the second edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- maintenance code: description of the depreciation of the UV irradiance lamp during operation;
- operating position: information added for single capped lamps;
- spectroradiometric measuring system: new information about distance between sensor and lamp axis;
- measurement and evaluation procedure: separated detailed information for double capped fluorescent UV lamps and single capped fluorescent UV lamps;
- Annex C (normative), Method of test for irradiance maintenance: new information added;
- Annex D (normative), Reflector gauge: new information added;
- Annex E (normative), Lamp datasheets for measurement: complementary information added.

IEC PAS 63228:2020(E) This Book 12 defines LED Arrays with a rectangular shape and a circular light emitting surface. For each LED Array, this Book 12 also defines the mechanical interface between the LED Array and the corresponding Holder. The mechanical interface between the Holder and the Luminaire (e.g. outline, OCA and mounting holes) is defined in [Book-10]. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. In addition, this Book 1 specifies general requirements for Zhaga compliant components of LED Luminaires.

IEC PAS 63324:2020(E) This Book 10 defines interfaces between LED Modules, associate components (Holders) and luminaires. Not all interface descriptions are applicable to LED Modules or Holders, but where applicable they are identical. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. In addition, this Book 1 specifies general requirements for Zhaga compliant components of LED Luminaires.

IEC PAS 63329:2020(E) This Book 14 defines three socketable LED Light Engines (with integrated Electronic Control Gears) and three socketable LED Modules (without integrated Electronic Control Gears). These LED Modules and LLEs have a rectangular shape and are typically applied in general lighting applications. These products are intended to be installed and replaced by professionals and non-professionals. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. In addition, this Book 1 specifies general requirements for Zhaga compliant components of LED Luminaires.

IEC 62868-2-1:2020 specifies safety requirements for semi-integrated organic light emitting diode modules operating with an external controlgear connected to the mains voltage, and which, in addition, have a control means inside ("semi-integrated") for operation under constant voltage, constant current or constant power and have a rated voltage up to 120 V ripple free DC or 50 V AC RMS at 50 Hz or 60 Hz.

IEC 62868-2-2:2020 specifies the safety requirements for integrated organic light-emitting diode (OLED) modules for use on ripple free DC supplies up to 1000 V or AC supplies up to 1 000 V RMS at 50 Hz or 60Hz.

IEC 62868-1:2020 specifies general safety requirements of OLED products for use on DC supplies up to 1000 V or AC supplies up to 1000 V at 50 Hz or 60 Hz for indoors and similar general lighting purposes.
This document applies to any OLED light sources which are not covered by IEC 62868-2 (all parts).
This first edition cancels and replaces IEC 62868 published in 2014.

IEC 63146:2019 establishes requirements for specification sheets relating to light emitting diode (LED) packages designed for the emission of white light for general lighting applications. This document does not contain compliance criteria.

IEC 61167:2018 specifies the performance requirements for metal halide lamps for general lighting purposes.
This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition.
a) A set of new lamp data sheets has been introduced for lamp types designed for replacing high pressure sodium lamps.
b) A set of new lamp data sheets has been introduced for 4 200 K versions of 3 000 K lamp types already in the standard.
c) A set of new lamp data sheets has been introduced for new lamp types where high frequency ignition data is important.
d) Annex G has been revised to incorporate high frequency ignition. As a consequence of this change, all data sheets in the standard have been revised to a new format.
e) A new informative Annex K has been introduced, giving recommended methods of making lamp temperature measurements.
The contents of the corrigendum of April 2019 have been included in this copy.

IEC TR 63130:2018(E) describes the current state of experts’ opinions on the standardization of metal halide lamps to cover the relevant parameters for hot restrike and for dimming in combination with low frequency square wave ballasts. It provides guidelines for supplementing or modifying IEC 61167 in order that these conditions are covered.

IEC 62031:2018 specifies general and safety requirements for light-emitting diode (LED) modules:
- non-integrated LED modules (LEDni modules) and semi-integrated LED modules (LEDsi modules) for operation under constant voltage, constant current or constant power;
- Integrated LED modules (LEDi modules) for use on DC supplies up to 250 V or AC supplies up to 1 000 V at 50 Hz or 60 Hz.
This second edition cancels and replaces the first edition published in 2008, Amendment 1:2012 and Amendment 2:2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a. the scope was clarified as well as the wording in several other clauses;
b. the normative references were updated;
c. the definitions for "replaceable LED module", "non-replaceable LED module" and "non-user replaceable LED module" were introduced while other definitions covered by IEC 62504 have been removed;
d. the marking clause was restructured and a table added to provide an informative overview;
e. the marking requirements for built-in LED modules were changed;
f. the entry for the marking with the working voltage was revised;
g. the provisions for terminals and heat management were revised;
h. Annex B was deleted;
i. information for luminaire design with regard to working voltage and water contact was introduced;
j. an abnormal temperature test was introduced.

The contents of the interpretation sheet 1 of July 2017 have been included in this copy.

IEC 60810:2014 is applicable to lamps (filament lamps, discharge lamps and LED light sources) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are listed in IEC 60809. However, the standard may also be used for other lamps falling under the scope of this standard. This fourth edition cancels and replaces the third edition, published in 2003, its Amendments 1 (2008) and 2 (2013). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) introduction of new gas discharge light sources;
b) introduction of requirements for non-replaceable filament lamps;
c) introduction of requirements and test conditions for LED packages.

IEC TS 62861:2017(E) This Technical Specification provides guidelines for establishing confidence in product reliability using principal component testing for LED light sources and LED luminaires for general lighting. It includes methods and criteria using initial qualification tests and accelerated stress tests of the principal components. The performance of any principal component will influence the performance of the final product.
Techniques to validate full lifetime claims and lumen maintenance projection are outside the scope of this Technical Specification. The following principal components are included in the testing if they are used as an integral part for the LED light source or LED luminaire:
- LED package and interconnects;
- optical materials;
- electronic subassemblies;
- cooling systems, both active (e.g. fans) and passive (e.g. thermal interface material);
- construction materials.
This Technical Specification is not recommended for use as a normative reference to the LED product performance standards.

IEC 62931:2017 This document specifies the safety and interchangeability requirements together with the test methods and conditions required to show compliance of non-integrated tubular LED lamps, intended for general lighting purposes, having:
a rated wattage up to 70 W,
a rated voltage up to 190 V ripple free DC,
GX16t-5 cap as listed in Table 1.  The requirements of this document relate only to type testing.

IEC 60969:2016 specifies performance requirements together with test methods and conditions required to show compliance of self-ballasted compact fluorescent lamps intended for general lighting services. This second edition cancels and replaces the first edition published in 1988, Amendment 1:1991 and Amendment 2:2000. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) title change;
b) scope is now limited to compact fluorescent lamps, but expanded to cover all lamps of voltages greater than 50 V and all power ratings;
c) introduction of requirements for lamp equivalency claims, switching withstand, starting time;
d) low temperature, run up time, treatment of claims for different operating conditions;
e) enhanced assessment and compliance criteria especially for lifetime;
f) introduction in-rush test conditions and displacement factor.
The contents of the corrigendum of January 2017 have been included in this copy.

Describes how the concentrations of dissolved gases or free gases may be interpreted to diagnose the condition of oil-filled electrical equipment in service and suggests future action.  Applicable to electrical equipment filled with mineral insulating oil and insulated with cellulosic paper or pressboard-based solid insulation.  Information about specific types of equipment   such as transformers (power, instrument, industrial, railways, distribution), reactors, bushings, switchgear and oil-filled cables is given only as an indication in the application notes.  May be applied only with caution to other liquid-solid insulating systems. In any case, the indications obtained should be viewed only as guidance and any resulting action should be undertaken only with proper engineering judgement.

IEC TS 62972:2016 establishes terms and definitions specific for general lighting OLED light sources and related equipment.