CLC/TC 100X - Audio, video and multimedia systems and equipment and related sub-systems

IEC 63296-2:2023 is applicable to active acoustic noise-cancelling headphones and earphones that have the function of reducing the ambient noise heard by the user by the level of the output sound from the transducer, which is generated by the ambient noise detection microphone and the noise reduction signal processing circuit. This document covers headphones and earphones to be worn over-the-ear or in-ear, all of which are referred to as "headphones" in this document. This document specifies the terms and definitions relating to battery duration of this type of headphones and the measurement and evaluation methods. The noise-detection microphones are mounted in the body, on the surface, or on an accessory of the headphones. Signal-processing circuits are analogue and digital electronic circuits. This document does not deal with equipment intended for hearing protection. It is also not applicable to music players, recorders, etc. that have a noise-cancelling function. The battery duration measurement methods can be applied to headphones having no active noise-cancelling function.

IEC 60268-24:2023 is applicable to active acoustic noise-cancelling headphones and earphones which have the function of reducing the noise heard by the user by the output sound from the transducer generated by the environment noise detection microphone and the noise reduction signal processing circuit. This document specifies the terms and definitions of this type of headphones or earphones, the characteristics to be specified, and the measurement and evaluation methods. The noise detection microphone or microphones are mounted in the body, on the surface, or on an accessory of the headphones or earphones. Signal processing circuits are analogue and digital electronic circuits. This document does not deal with equipment intended for hearing protection. The noise cancelling characteristic measurement methods can be applied to headphones and earphones having no active noise cancelling function.

IEC 63474:2023 specifies methods of measurement of electrical power consumption in networked standby and the reporting of the results for edge equipment. Power consumption in standby (other than networked standby) is covered by EN 50564, including the input voltage range. This document also provides a method to test power management and to test whether it is possible to deactivate wireless network connection(s). This document does not apply to the measurement of electrical power consumption in networked standby for interconnecting equipment.

IEC 60268-23:2023 specifies acoustical measurement methods that apply to TV sets, monitors with built-in loudspeakers, and other audio devices having similar acoustical properties (e.g. flat-panel loudspeakers). The acoustical measurements are performed under free-field conditions and in-situ. This document does not assess the perception and cognitive evaluation of the reproduced sound, nor the impact of perceived sound quality.

IEC 62087-3:2023 is available as IEC 62087-3:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62087-3:2023 specifies the determination of the power consumption and related characteristics of television sets. Television sets include, but are not limited to, those with LCD, OLED, or projection technologies. The operating modes and functions, as they specifically apply to television sets, are defined in detail in this part of IEC 62087. This document is limited to television sets that can be connected to an external power source. Television sets that include a non-removable, main battery are not covered by this document. Television sets can include any number of auxiliary batteries. The measuring conditions in this document represent the normal use of the equipment and can differ from specific conditions, for example as specified in safety standards. IEC 62087-3:2023 cancels and replaces the first edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) it introduces measuring procedures for the determination of power consumption in the On mode while viewing static metadata HDR video content; b) all tests for On mode power determination are performed with MDD disabled; c) only progressive video signals are used for testing; d) a dimmable LED reflector lamp is used as a light source for illuminating the ABC sensor to achieve specific illuminance levels; e) a dynamic box and outline video signal is used for determining the ratio of peak luminance.

IEC 62087-2:2023 is available as IEC 62087-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 62087-2:2023 specifies the signals used to determine the power consumption of audio, video, and related equipment, such as television sets and computer monitors. It also specifies signals for determining the peak luminance ratio that is sometimes associated with television set power consumption measurement programs. In addition, this part specifies equipment, interfaces, and accuracy related to signal generation. IEC 62087-2:2023 cancels and replaces the first edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) HDR and UHD video test signals have been added; b) dynamic box and outline test signals have been added, replacing the static box and outline test signals; c) all test signals are provided as media files for download from a specified IEC online repository, which replaces previous DVD and Blu-ray media.

IEC 60098:2020 applies to analogue audio disk records and the corresponding professional and domestic reproducing equipment. It excludes amplifiers and loudspeakers, methods of measurement for which can be found in IEC 60268-3, IEC 60268-5, IEC 60268­21 and IEC 60268-22. IEC 60098:2020 specifies the characteristics that are necessary to ensure compatibility between analogue audio disk records and the corresponding reproducing equipment. It also lists and defines the most important characteristics affecting the performance of reproducing equipment, and establishes agreed methods of measurement for these characteristics. IEC 60098:2020 cancels and replaces the third edition published in 1987. This edition constitutes a full revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of a tolerance on groove width.

This document specifies a reference model for spatial wireless power transfer based on multiple magnetic resonances (SWPT-MMR), which is non-radiative wireless power transfer (WPT). The document contains overview of SWPT-MMR and a reference model.

The specification is primarily targeted at peripheral developers and platform/adapter developers, but provides valuable information for platform operating system/BIOS/device driver, adapter independent hardware vendors/independent software vendors, and system OEMs. This specification can be used for developing new products and associated software.

IEC 63006:2019 specifies terminology and definitions related to wireless power transfer (WPT) technologies below 30 MHz to promote global harmonization of wireless power transfer terminology. This document does not address terminology of wireless power transfer outside the scope of IEC TC 100 (Audio, video and multimedia systems and equipment), such as human exposure or safety.

IEC 63207:2022 specifies measurement methods for optical performance (luminance) and blue light characteristics (BLCs) of visual display terminals (VDTs), excluding displays for outdoor use only.

This standard defines specification and control protocol of D2DWC module for using wireless power TX and RX functions by only one single device. And the related antenna physical design examples are presented in Annex A for sharing information. This standard propose D2DWC module circuit requirement which are consisted with the D2DWC main AP, D2DWC IC, EMT/WPT Antenna Unit and PMIC unit. In the Chapter 5, ‘Specifications and control protocol of D2DWC’, the register information and message protocols for WPT control are defined in order to implement the WPT TX function. In this standard, the interface and protocol in the wireless power process of the mobile device can be used in accordance with the corresponding wireless power transfer standard. Any wireless power transfer standard working inside 100 - 350 kHz frequency range can be included from the scope of this standard. This standard can be used to mobile wireless power transfer in mobile phones and other mobile devices, IoT, and micro-sensor industries and related application fields.

This standard defines procedures for transferring power to non-powered IoT devices using the existing ISM band communication infrastructure and RF WPT and a protocol for a two-way, long-distance wireless network in which IoT devices and APs communicate using backscatter modulation of ISM-band signals. Three components are required for two-way, long-distance wireless communication using backscatter modulation of ISM-band signals: an STA that transmits wireless power and data packets to SSNs by forming ISM-band signal channels between HIE-APs, a batteryless SSN that changes the sensitivity of the channel signals received from the STA using backscatter modulation, and an HIE-AP that practically decodes the channel signals whose sensitivity was changed by the SSN. In this standard, the procedures for CW-type RF WPT using communication among these three components are specified based on application of the CSI or RSSI detection method of ISM-band communication. This standard proposes a convergence communication protocol than can deploy sensors, which can operate at low power (dozens of microwatts or less) without batteries, collect energy, and perform communication, to transmit power to SSNs using RF WPT based on parasitic communication. This method can be applied to application service areas such as domestic IoT, the micro-sensor industry, and industries related to environmental monitoring in the future

IEC 62680-1-5:2019 describes the minimum capabilities and characteristics an audio device shall support to comply with the USB. This document also provides recommendations for optional features. The Audio Device Class Definition applies to all devices or functions embedded in composite devices that are used to manipulate audio, voice, and sound-related functionality. This includes both audio data (analog and digital) and the functionality that is used to directly control the audio environment, such as Volume and Tone Control. The Audio Device Class does not include functionality to operate transport mechanisms that are related to the reproduction of audio data, such as tape transport mechanisms or CD-ROM drive control.

IEC 62680-1-7:2019 describes in detail all the Audio Data Formats that are supported by the Audio Device Class. This document is considered an integral part of the Audio Device Class Specification, although subsequent revisions of this document are independent of the revision evolution of the main USB Audio Specification. This is to easily accommodate the addition of new Audio Data Formats without impeding the core USB Audio Specification.

IEC 62680-1-8:2019 is to describe in detail all the Terminal Types that are supported by the Audio Device Class. This document is considered an integral part of the Audio Device Class Specification, although subsequent revisions of this document are independent of the revision evolution of the main Audio Device Class Specification. This is to easily accommodate the addition of new Terminal Types without impeding the core Audio Device Class Specification. The Audio Device Class Definition applies to all devices or functions embedded in composite devices. All audio signals inside an audio function start at an Input Terminal, pass through some Units, and leave the function through an Output Terminal. Units can manipulate the signal in various ways. Terminals represent the connections of the function to the outside world. As part of the Terminal descriptor, the wTerminalType field specifies the vendor’s suggested use of the Terminal. For example, a pair of speakers is a more suitable target for music output than a telephone line. This feature allows a vendor to ensure that applications use the device in a consistent and meaningful way.

The purpose of IEC 62680-1-6:2019 is to create a higher level of interoperability among Hosts and Audio Devices. By establishing a set of essential audio features, users can expect a consistent experience, Device manufacturers have a solid template to follow, and Host drivers may be simplified. The USB Audio Device Class Definition for Basic Audio Functions applies to all USB Audio Functions that are based on the Universal Serial Bus Device Class Definition for Audio Devices Release 3.0. It defines baseline audio functionality for all ADC 3.0 compliant Hosts and Devices.

IEC 63033-3:2019 specifies measurement methods for the drive monitoring system that is specified in IEC TS 63033-1:2017.

IEC 62680-1-3:2022 defines the USB Type-C® receptacles, plug and cables. The USB Type-C Cable and Connector Specification is guided by the following principles: - Enable new and exciting host and device form-factors where size, industrial design and style are important parameters - Work seamlessly with existing USB host and device silicon solutions - Enhance ease of use for connecting USB devices with a focus on minimizing user confusion for plug and cable orientation The USB Type-C Cable and Connector Specification defines a new receptacle, plug, cable and detection mechanisms that are compatible with existing USB interface electrical and functional specifications. This specification covers the following aspects that are needed to produce and use this new USB cable/connector solution in newer platforms and devices, and that interoperate with existing platforms and devices: - USB Type-C receptacles, including electro-mechanical definition and performance requirements - USB Type-C plugs and cable assemblies, including electro-mechanical definition and performance requirements - USB Type-C to legacy cable assemblies and adapters - USB Type-C-based device detection and interface configuration, including support for legacy connections - USB Power Delivery optimized for the USB Type-C connector The USB Type-C Cable and Connector Specification defines a standardized mechanism that supports Alternate Modes, such as repurposing the connector for docking-specific applications. IEC 62680-1-3:2022 cancels and replaces the fourth edition published in 2021 and constitutes a technical revision. This standard is the USB-IF publication Universal Serial Bus Type-C Cable and Connector Specification Revision 2.0. New release primarily for enabling Extended Power Range (EPR) and defining EPR cables aligning with USB Power Delivery Specification R3.1 V1.0. Also includes incorporation of all approved ECNs as the revision date plus editorial clean-up.

This International Standard specifies the audio reproduction method for normalized loudness
level of audio sources for consumer equipment and systems.

This International Standard covers personal computing products. It applies to desktop and notebook computers as defined in 4.1 that are marketed as final products and that are hereafter referred to as the equipment under test (EUT) or product. This standard specifies: - a test procedure to enable the measurement of the power and/or energy consumption in each of the EUT's power modes; - formulas for calculating the typical energy consumption (TEC) for a given period (normally annual); - a majority profile that should be used with this standard which enables conversion of average power into energy within the TEC formulas; - a pre-defined format for the presentation of results. This standard does not set any pass/fail criteria for the EUTs. Users of the test results should define such criteria.

This part of IEC 63033 specifies recording methods of the surround view system that is specified in IEC 63033-1 in order to view the recorded video file with free eye point technology.

This document specifies measurement methods for the surround view system that is specified in IEC 63033-1.

This document specifies that is the multiple camera composite images generated by the surround view system of IEC 63033-1 is applied to the FOV and display requirement specified UN Regulation No. 46.

This part of IEC 63033 specifies the model for generating the surrounding visual image of the surround view system.

This part of IEC 63246 specifies the CCIS requirements, which include the general, functional and service requirements for CCIS.

This part of IEC 63246 describes the CCIS framework, which includes the information flows for registration, device monitoring and control, and content delivery between CCIS functional entities.

This part of IEC 63033 specifies recording methods of the drive monitoring system that is specified in IEC TS 63033-1 in order to view the recorded video file with free eye point technology.

IEC 60268-21:2018 specifies an acoustical measurement method that applies to electro-acoustical transducers and passive and active sound systems, such as loudspeakers, TV-sets, multi-media devices, personal portable audio devices, automotive sound systems and professional equipment. The device under test (DUT) can be comprised of electrical components performing analogue and digital signal processing prior to the passive actuators performing a transduction of the electrical input into an acoustical output signal. This document describes only physical measurements that assess the transfer behaviour of the DUT between an arbitrary analogue or digital input signal and the acoustical output at any point in the near and far field of the system. This includes operating the DUT in both the small and large signal domains. The influence of the acoustical boundary conditions of the target application (e.g. car interior) can also be considered in the physical evaluation of the sound system. This document does not assess the perception and cognitive evaluation of the reproduced sound and the impact of perceived sound quality.

1.1 Equipment in the scope of this standard This European Standard specifies methods of measurement of electrical power consumption in networked standby and the reporting of the results for edge equipment. Power consumption in standby (other than networked standby) is covered by EN 50564, including the input voltage range. This European Standard also provides a method to test power management and whether it is possible to deactivate wireless network connection(s). NOTE 1 This standard has been written in particular to support Commission Regulation (EU) No 801/2013 for the measurement of energy consumption in networked standby. This standard applies to electrical products with a rated input voltage of 230 V a.c. for single phase products and 400 V a.c. for three phase products. NOTE 2 The measurement of energy consumption and performance of products during intended use are generally specified in product standards and are not covered by this standard. NOTE 3 The term "products" in this standard includes household appliances or information technology products, consumer electronics, audio, video and multimedia systems; however the measurement methodology could be applied to other products. Where this standard is referenced by more specific standards or procedures, these should define and name the relevant conditions to which this test procedure is applied. 1.2 Equipment not in the scope of this standard This European Standard does not apply to the measurement of electrical power consumption in networked standby for interconnecting equipment. NOTE Measurement of electrical power consumption in networked standby for interconnecting equipment is the subject of ETSI standard EN 303 423 "Environmental Engineering (EE) - Electrical and electronic household and office equipment; Measurement of networked standby power consumption for interconnecting equipment".

NEW!IEC 60268-4:2018 is available as IEC 60268-4:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60268-4:2018 specifies methods of measurement for the electrical impedance, sensitivity, directional response pattern, dynamic range and external influences of sound system microphones, and also details the characteristics to be specified by the manufacturer. It applies to sound system microphones for all applications for speech and music. It does not apply to measurement microphones, but it does apply to each audio channel of microphones having more than one channel, for example for stereo or similar use. It is also applicable to flush-mounted microphones and to the analogue characteristics of microphones with digital audio output. For the purposes of this International Standard, a microphone includes all such devices as transformers, pre-amplifiers, or other elements that form an integral part of the microphone, up to the output terminals specified by the manufacturer. The major characteristics of a microphone are considered in Clauses 6 to 21. Additional characteristics are considered in Annex A and Annex C. IEC 60268-4:2018 cancels and replaces the fifth edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) subclause 19.4 on "pop" measurement replaces Annex C; b) new Annex D for noise measurements in the digital domain.

IEC 63246-1:2021 describes the general considerations of CCIS, which include the system model of the CCIS and the types of CCIS clients with the associated service flows.

IEC 60958-1:2021 is available as IEC 60958-1:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60958-1:2021 describes a serial, uni-directional, self-clocking interface for the interconnection of digital audio equipment for consumer and professional applications. It provides the basic structure of the interface. Separate documents define items specific to particular applications. The interface is primarily intended to carry monophonic or stereophonic programmes, encoded using linear PCM and with a resolution of up to 24 bits per sample. When used for other purposes, the interface is able to carry audio data coded other than as linear PCM coded audio samples. Provision is also made to allow the interface to carry data related to computer software, multimedia technologies, or signals coded using non linear PCM. The format specification for these applications is not part of this document. The interface is intended for operation at audio sampling frequencies of 32 kHz and above. Auxiliary information is transmitted along with the programme. IEC 60958-1:2021c ancels and replaces the third edition published in 2008, and Amendment 1:2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The relevant part of IEC 60958-5 is supported.

This part of IEC 60958 specifies the consumer application of the interface for the inter connection of digital audio equipment defined in IEC 60958-1. NOTE When used in a consumer digital processing environment, the interface is primarily intended to carry stereophonic programmes, with a resolution of up to 20 bits per sample, an extension to 24 bits per sample being possible.

This part of IEC 63087 specifies requirements, and the associated methods of measurement, for the electroacoustic performance of personal listening systems. This document specifies requirements for the provision of assistive listening in audio, video and multimedia systems and equipment. The requirements are of different kinds, because of the diversity of the hardware concerned. Existing IEC standards for methods of measurement are normatively referenced if they exist. Methods of measurement and performance requirements are specified in IEC 63087-21. This document does not apply to hearing aids. Also excluded are devices entirely worn on or in the ear, which cannot be measured independently.

IEC 63296-1:2021 specifies the methods for measuring the battery duration at defined sound pressure levels for continuous music playback of battery-powered loudspeaker equipment. A primary battery or secondary battery can be used as a power source for the loudspeaker and its composite equipment. In the case of composite equipment, this method for the measurement of battery duration can be applied under the condition of powered loudspeaker playback only.

NEW!IEC 60268-3:2018 is available as IEC 60268-3:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60268-3:2018 applies to analogue amplifiers, and the analogue parts of analogue/digital amplifiers, which form part of a sound system for professional or household applications. It specifies the characteristics that should be included in specifications of amplifiers and the corresponding methods of measurement. This part of IEC 60268 shall be used in conjunction with IEC 60268-1:1985 and IEC 60268 2:1987. This fifth edition cancels and replaces the fourth edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) rated condition of digital input is newly specified; b) tolerance of rated power supply is changed; c) maximum effective output power is appended to output characteristics list; d) "Terms, definitions and rated values" clause is complemented.

IEC 62680-1-4:2018(E) provides a means for authenticating Products with regard to identification and configuration. Authentication is performed via USB Power Delivery message communications and/or via USB data bus control transactions. This specification defines the architecture and methodology for unilateral Product Authentication. It is intended to be fully compatible with and extend existing PD and USB infrastructure. Information is provided to allow for Policy enforcement, but individual Policy decisions are not specified.

This part of IEC 63245 specifies requirements for spatial wireless power transfer based on multiple magnetic resonances (SWPT-MMR), which is a non-radiative wireless power transfer (WPT). This document contains two categories of requirements: general requirements and functional requirements. The general requirements cover charging procedures and charging zones. The functional requirements cover each component of a SWPT-MMR system, such as transmitter coils.

IEC 62680-1-3:2021 defines the USB Type-C™ receptacles, plug and cables. The USB Type-C Cable and Connector Specification defines a new receptacle, plug, cable and detection mechanisms that are compatible with existing USB interface electrical and functional specifications. This specification covers the following aspects that are needed to produce and use this new USB cable/connector solution in newer platforms and devices, and that interoperate with existing platforms and devices: - USB Type-C receptacles, including electro-mechanical definition and performance requirements - USB Type-C plugs and cable assemblies, including electro-mechanical definition and performance requirements - USB Type-C to legacy cable assemblies and adapters - USB Type-C-based device detection and interface configuration, including support for legacy connections - USB Power Delivery optimized for the USB Type-C connector. This specification is intended as a supplement to the existing USB 2.0, USB 3.1 and USB Power Delivery specifications. It addresses only the elements required to implement and support the USB Type-C receptacles, plugs and cables. Normative information is provided to allow interoperability of components designed to this specification. Informative information, when provided, may illustrate possible design implementations. IEC 62680-1-3:2021 cancels and replaces the third edition published in 2018 and constitutes a technical revision. New release primarily for enabling USB4 over USB Type-C connectors and cables. Also includes incorporation of all approved ECNs as of the revision date plus editorial clean-up.

IEC 60958-5:2021 enhances the consumer application of the interface for the interconnection of digital audio equipment defined in IEC 60958-1 and IEC 60958-3, introducing: - multichannel; - multi-stream; - high-resolution; - multimedia extension; - related applications.

NEW!IEC 62684:2018 is available as IEC 62684:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62684:2018 specifies the interoperability of common external power supplies for use with data-enabled mobile telephones. It defines the common charging capability and specifies interface requirements for the external power supply. Safety and EMC aspects are not covered by this document. Safety is covered by IEC 60950-1 or IEC 62368-1 and EMC is covered by regional /national standards. This document defines interoperability based on legacy USB technologies and does not cover charging interfaces that implement IEC 62680-1-3, IEC 62680-1-2 and IEC 63002. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Clause 1 is modified to include updated references to IEC Universal Serial Bus interface standards; b) Clause 2 is expanded to include references to IEC Universal Serial Bus interface standards; c) Subclause 4.1 is expanded to include requirements for non USB Micro-B plug DC plug connectors; d) Subclause 4.4 is modified to remove obsolete requirements for common mode noise and reference requirements of IEC Universal Serial Bus interface standards; e) Subclause 4.5 is modified to reference appropriate safety standards.

NEW!IEC 61938:2018 is available as IEC 61938:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61938:2018 gives guidance on current practice for the characteristics of multimedia analogue interfaces to achieve interoperability between equipment from different manufacturers. It is not a performance standard. Recommendations for interfaces for equipment used in vehicles, and for analogue video interfaces for broadcast and similar equipment, are not given. Refer to IEC 60958 for the interconnection of digital signals. This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) electric tolerance is standardized; b) recommended value of output source impedance is adjusted; c) value of 6 Ohms is additionally recommended to impedance-defined loudspeaker systems; d) values in each table are chosen with respect to the state of the art and representative of best practice in industry.

IEC 62731:2018(E) specifies the text-to-speech functionality for a (broadcast) receiver with a text-to-speech system. Such a system may be one device, i.e. a receiver with an integrated text-to-speech generator, or may be two devices, i.e. a receiver interfacing with an external text-to-speech device. This document applies only to completely functional stationary (or semi-stationary) digital TV receivers such as set top boxes, integrated digital TVs, recorders and other products whose primary function is to receive TV content. Where this document refers to TV, this will be shorthand for all such receivers. This document does not apply to products that are capable of receiving TV as a secondary function (e.g. PCs or game consoles with digital television receivers). It also does not apply to sub-assemblies (e.g. PC tuner cards). This edition includes the following significant technical changes with respect to the previous edition: a) in 6.2, the levels of announcement quality were revised as well as considerations for ways in which device users can provide service providers with feedback on incorrectly announced terms. b) in 6.3, the following TV functionality was added: the TV can receive updated words, associated conversions and updated conversion rules for the TTS engine via a network connection.

This part of IEC 62087 specifies the determination of the power consumption of computer monitors including, but is not limited to, those with CRT, LCD, PDP or OLED technologies. Computer monitors that include touch screen functionality are included in the scope of this document. This document is limited to computer monitors that are powered from a main power source other than a battery. Computer monitors that are powered from a battery source are not covered by this document. However mains-powered computer monitors may include any number of auxiliary batteries. Computer monitors connected by digital inputs such as DisplayPort, HDMI, DVI, or by analogue VGA input, are considered in this document. This document does not apply to network- and wirelessly connected computer monitors. A computer monitor is a display device that does not include a TV tuner and is intended to be used to display the video signals from a computer. These video signals are produced from software programs that are operating within the computer and can consist of static and moving images. As such, test procedures using static patterns, dynamic video and web-based video are specified. The test methods specified in this document can be applied to computer monitors of any size, however, this document is not applicable to specialized monitors associated with medical equipment, publishing and other professional, commercial or industrial uses. The various modes of operation that are relevant for measuring power consumption are also defined. The measuring conditions in this document represent the normal use of the equipment and can differ from specific conditions, for example as specified in safety standards.

IEC 60268-16:2020 defines the STI model, test signals, measurement and prediction methods. The objective of this document is to provide a comprehensive manual for all types of users of the STI model in the fields of audio, communications and acoustics. This document does not provide STI criteria for certification of transmission channels (e.g. criteria for a voice-alarm system), but some typical application values are provided in Annex G. Every measurement method has limitations, and the reader is referred to clauses relating to limitations such as speech privacy, echo and systems using digital voice compression (vocoders). This document does not cover the case of fluctuating noise on the STI, although some general comments on dealing with this complex issue are provided in 7.13 and 8.9.3. IEC 60268-16:2020 cancels and replaces the fourth edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the spectrum of the male speech test signal has been changed, with significant reductions in the 125 Hz and 250 Hz bands being implemented; b) some corrections to formulae have been made; c) additional information has been included on prediction and measurement procedures; d) spectrum and weighting factors for female speech have been removed; e) verification information for STI measurement devices added; f) the relationships between STI and number of other speech intelligibility measures have been updated in Annex E; g) greater information is given in Annex M about adjustments to the measured STI results to simulate effects of alternative ambient noise and speech levels.

IEC 60268-22:2020 applies to transducers converting an electrical input signal into a mechanical or acoustical output signal. However, if the electrical input terminals and the surface of the radiator are accessible, this document can also apply to passive and active sound systems such as loudspeakers, headphones, TV-sets, multi-media devices, personal portable audio devices, automotive sound systems and professional equipment. This document describes only electrical and mechanical measurements that help assess the transfer behaviour of the device under test (DUT). This includes operating the DUT in both the small- and large-signal domains. The influence of the target application's acoustical boundary conditions (e.g. car interior) can also be considered in the physical evaluation of the sound system. Perception and cognitive evaluations of the reproduced sound and the impact of perceived sound quality are outside the scope of this document.

IEC 63034:2020 specifies the characteristics of microspeakers as well as the relevant test methods on microspeakers using steady-state sinusoidal signals, sinusoidal chirp, multi-tone or noise. The main characteristics include, but are not limited to, impedance, displacement, amplitude frequency response, distortion, and power handling.