EN IEC 63563-4:2025

SLOVENSKI STANDARD
01-marec-2026
Različica specifikacije Qi 2.0 - 4. del: Zagotavljanje napajanja (IEC 63563-4:2025)
Qi Specification version 2.0 - Part 4: Power delivery (IEC 63563-4:2025)
Qi Spezifikation Version 2.0 - Teil 4: Energiesversorgung (IEC 63563-4:2025)
Spécification Qi version 2.0 - Partie 4: Alimentation électrique (IEC 63563-4:2025)
Ta slovenski standard je istoveten z: EN IEC 63563-4:2025
ICS:
29.240.99 Druga oprema v zvezi z Other equipment related to
omrežji za prenos in power transmission and
distribucijo električne energije distribution networks
33.160.99 Druga avdio, video in Other audio, video and
avdiovizuelna oprema audiovisual equipment
35.200 Vmesniška in povezovalna Interface and interconnection
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63563-4

NORME EUROPÉENNE
EUROPÄISCHE NORM March 2025
ICS 29.240.99; 35.240.99
English Version
Qi Specification version 2.0 - Part 4: Power Delivery
(IEC 63563-4:2025)
Spécification Qi version 2.0 - Partie 4: Alimentation Qi Spezifikation Version 2.0 - Teil 4: Energiesversorgung
électrique (IEC 63563-4:2025)
(IEC 63563-4:2025)
This European Standard was approved by CENELEC on 2025-03-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63563-4:2025 E

European foreword
The text of document 100/4249/FDIS, future edition 1 of IEC 63563-4, prepared by TC 100/Technical
Area 15 "Wireless Power Transfer" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 63563-4:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-03-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-03-31
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63563-4:2025 was approved by CENELEC as a European
Standard without any modification.

IEC 63563-4 ®
Edition 1.0 2025-02
INTERNATIONAL
STANDARD
Qi Specification version 2.0 –

Part 4: Power Delivery
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.240.99; 35.240.99 ISBN 978-2-8327-0187-4

 ,(&‹,(&
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
QI SPECIFICATION VERSION 2.0 –
Part 4: Power Delivery
FOREWORD
 The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprisingall
national electrotechnical committees (IEC National Committees). The object of IEC is to promote internationalco-
operation on all questions concerning standardization in the electrical and electronic fields. To this end andin addition
to other activities, IEC publishes International Standards, Technical Specifications, TechnicalReports, Publicly
Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Theirpreparation is entrusted to
technical committees; any IEC National Committee interested in the subject dealt withmay participate in this
preparatory work. International, governmental and non-governmental organizationsliaising with the IEC also
participate in this preparation. IEC collaborates closely with the InternationalOrganization for Standardization
(ISO) in accordance with conditions determined by agreement between the twoorganizations.
 The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
 IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
 In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence betweenany IEC
Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
 IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
 All users should ensure that they have the latest edition of this publication.
 No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage orother
damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) andexpenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IECPublications.
 Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
 IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights inrespect
thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s),which may be
required to implement this document. However, implementers are cautioned that this may notrepresent the latest
information, which may be obtained from the patent database available athttps://patents.iec.ch. IEC shall
not be held responsible for identifying any or all such patent rights.
IEC 635-4 has been prepared by technical area 15: Wireless Power Transfer, of IEC
technical committee 100: Audio, video and multimedia systems and equipment. It is an
International Standard.
It is based on Qi Specification version 2.0, Power Delivery and was submitted as a Fast-Track
document.
The text of this International Standard is based on the following documents:
Draft Report on voting
//FDIS //RVD
,(&‹,(& 
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
The structure and editorial rules used in this publication reflect the practice of the organization
which submitted it.
This document was developed in accordance with ISO/IEC Directives, Part 1 and ISO/IEC
Directives, IEC Supplement available at www.iec.ch/members_experts/refdocs. The main
document types developed by IEC are described in greater detail at www.iec.ch/publications.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
x reconfirmed,
x withdrawn, or
x revised.
 ,(&‹,(&
WIRELESS POWER
CONSORTIUM
Qi Specification
Power Delivery
Version 2.0
April 2023
,(&‹,(& 
DISCLAIMER
Theinformationcontainedhereinisbelievedtobeaccurateasofthedateofpublication,
butisprovided“asis”andmaycontainerrors.TheWirelessPowerConsortiummakesno
warranty,expressorimplied,withrespecttothisdocumentanditscontents,includingany
warrantyoftitle,ownership,merchantability,orfitnessforaparticularuseorpurpose.
NeithertheWirelessPowerConsortium,noranymemberoftheWirelessPower
Consortiumwillbeliableforerrorsinthisdocumentorforanydamages,includingindirect
orconsequential,fromuseoforrelianceontheaccuracyofthisdocument.For any further
explanation of the contents of this document, or in case of any perceived inconsistency or ambiguity
of interpretation, contact: info@wirelesspowerconsortium.com.
RELEASE HISTORY
Specification Version Release Date Description
2.0 April 2023 Initial release of the v2.0 Qi Specification.

 ,(&‹,(&
Table of Contents
1  General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Structure of the Qi Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6 Power Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2  Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3  Power Receiver construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Dual resonant circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 Rectification circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3 Sensing circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.4 Communications modulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.5 Communications demodulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6 Output disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.7 Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4  Power Receiver design guidelines (informative) . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1 Large-signal resonance check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2 Power Receiver coil design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5  Power Transmitter construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Power Transmitter reference designs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Power transfer control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6  Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7  Meaningful functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8  Unintentional Magnetic Field Susceptibility (Informative) . . . . . . . . . . . . . . . . . 24
8.1 Limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.2 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.3 Power Transmitter detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9  Load Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.1 Load step test procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2 Load dump test procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

,(&‹,(& 
10  Over-voltage protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11  External Power Input (Informative) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
11.1 Available power—Extended Power Profile only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12  Power Levels (Extended Power Profile only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.1 Potential Load Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.2 Light load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
13  System Efficiency (Informative). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.1 Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.2 Power Transmitter efficiency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
13.3 Power Receiver efficiency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
14  Stand-by Power (Informative) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
14.1 Transmitter Measurement Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
15  Object Detection (Informative) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
15.1 Resonance shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
15.2 Capacitance change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
16  Power Receiver Localization (Informative). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.1 Primary Coil array based Free Positioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.2 Moving Primary Coil based Free Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
16.3 User-assisted positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

 ,(&‹,(&
1 General
The Wireless Power Consortium (WPC) is a worldwide organization that aims to develop and
promote global standards for wireless power transfer in various application areas. A first
application area comprises flat-surface devices such as mobile phones and chargers in the
Baseline Power Profile (up to 5 W) and Extended Power Profile (above 5 W).
1.1 Structure of the Qi Specification
General documents
ƒ Introduction
ƒ Glossary, Acronyms, and Symbols
System description documents
ƒ Mechanical, Thermal, and User Interface
ƒ Power Delivery
ƒ Communications Physical Layer
ƒ Communications Protocol
ƒ Foreign Object Detection
ƒ NFC Tag Protection
ƒ Authentication Protocol
,(&‹,(& 
1.2 Scope
The QiSpecification,PowerDelivery (this document) comprises guidelines and requirements for
Power Receiver design, including circuitry, power consumption, operating power levels, power
transfer efficiency, and standby power.
1.3 Compliance
All provisions in the QiSpecification are mandatory, unless specifically indicated as recommended,
optional, note, example, or informative. Verbal expression of provisions in this Specification follow
the rules provided in ISO/IEC Directives, Part 2.
Table 1: Verbal forms for expressions of provisions
Provision Verbal form
requirement “shall” or “shall not”
recommendation “should” or “should not”
permission “may” or “may not”
capability “can” or “cannot”
1.4 References
For undated references, the most recently published document applies. The most recent WPC
publications can be downloaded from http://www.wirelesspowerconsortium.com.

 ,(&‹,(&
1.5 Conventions
1.5.1 Notation of numbers
ƒ Real numbers use the digits 0 to 9, a decimal point, and optionally an exponential part.
ƒ Integer numbers in decimal notation use the digits 0 to 9.
ƒ Integer numbers in hexadecimal notation use the hexadecimal digits 0 to 9 and A to F, and are
prefixed by "0x" unless explicitly indicated otherwise.
ƒ Single bit values use the words ZERO and ONE.
1.5.2 Tolerances
Unless indicated otherwise, all numeric values in the QiSpecification are exactly as specified and do
not have any implied tolerance.
1.5.3 Fields in a data packet
A numeric value stored in a field of a data packet uses a big-endian format. Bits that are more
significant are stored at a lower byte offset than bits that are less significant. Table 2 and Figure 1
provide examples of the interpretation of such fields.
Table 2: Example of fields in a data packet
b b b b b b b b
7 6 5 4 3 2 1 0
(msb)
B
16-bit Numeric Data Field
B
(lsb)
B Other Field (msb)
B 10-bit Numeric Data Field (lsb) Field
Figure 1. Examples of fields in a data packet
16-bit Numeric Data Field
b b b b b b b b b b b b b b b b
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
B B
0 1
10-bit Numeric Data Field
b b b b b b b b b b
9 8 7 6 5 4 3 2 1 0
B B
2 3
,(&‹,(& 
1.5.4 Notation of text strings
Text strings consist of a sequence of printable ASCII characters (i.e. in the range of 0x20 to 0x7E)
enclosed in double quotes ("). Text strings are stored in fields of data structures with the first
character of the string at the lowest byte offset, and are padded with ASCII NUL (0x00) characters
to the end of the field where necessary.
EXAMPLE: The text string “WPC” is stored in a six-byte fields as the sequence of characters 'W', 'P', 'C', NUL,
NUL, and NUL. The text string “M:4D3A” is stored in a six-byte field as the sequence 'M', ':', '4', 'D',
'3', and 'A'.
1.5.5 Short-hand notation for data packets
In many instances, the QiSpecification refers to a data packet using the following shorthand
notation:
/
In this notation, refers to the data packet's mnemonic defined in the QiSpecification,
CommunicationsProtocol, and refers to a particular value in a field of the data packet.
The definitions of the data packets in the QiSpecification,CommunicationsProtocol, list the
meanings of the modifiers.
For example, EPT/cc refers to an End Power Transfer data packet having its End Power Transfer
code field set to 0x01.
 ,(&‹,(&
1.6 Power Profiles
A Power Profile determines the level of compatibility between a Power Transmitter and a Power
Receiver. Table 3 defines the available Power Profiles.
ƒ BPPPTx: A Baseline Power Profile Power Transmitter.
ƒ EPP5PTx: An Extended Power Profile Power Transmitter having a restricted power transfer
()pot
capability, i.e. P = 5 W.
L
ƒ EPPPTx: An Extended Power Profile Power Transmitter.
ƒ BPPPRx: A Baseline Power Profile Power Receiver.
ƒ EPPPRx: An Extended Power Profile Power Receiver.
Table 3: Capabilities included in a Power Profile
Feature BPP PTx EPP5 PTx EPP PTx BPP PRx EPP PRx
Ax or Bx design Yes Yes No N/A N/A
MP-Ax or MP-Bx design No No Yes N/A N/A
Baseline Protocol Yes Yes Yes Yes Yes
Extended Protocol No Yes Yes No Yes
Authentication N/A Optional Yes N/A Optional

,(&‹,(& 
2 Introduction
Figure 2 provides a simplified model of a wireless power system, consisting of six blocks. The three
blocks to the left of the power transfer interface represent a Power Transmitter and its supply. The
three to the right represent a Power Receiver and its Load. Typically, these blocks comprise the
following elements.
Supply: in many cases a separate adapter such as a USB PD brick.
Inverter: a half-bridge or full-bridge for DC/AC conversion.
ResonantTank: a coil and series capacitor boosting the power transfer capability.
Rectifier: either a diode bridge or an active (synchronous) bridge for AC/DC conversion.
Load: a power sink drawn by the Power Receiver Product, typically a mobile phone's power input to
an internal battery charger.
Figure 2. Simplified model of a wireless power transfer system
Supply Input Transmitted Received Output Load
Power Power Power Power Power Power
Resonant Resonant
Inverter
Supply Rectifier Load
Tank Tank
PTx Power PRx
Power Transmitter Power Receiver
Input Transfer Output
Interface Interface Interface
With reference to Figure 2, the following definitions are central to the understanding of a wireless
power system.
PowerSignal—An alternating magnetic field.
SupplyPower—The power dissipated from the supply.
PowerTransmitter—A subsystem that can generate a Power Signal.
PowerTransmitterProduct—A device containing one or more Power Transmitters.
TransmittedPower—The power from the Power Signal dissipated by any object that is not an
integral part of the Power Transmitter Product.
PowerReceiver—A subsystem that can extract electric power from a Power Signal.
PowerReceiverProduct—A device containing a Power Receiver.
ReceivedPower—The power from the Power Signal dissipated by any component that is an
integral part of the Power Receiver Product.
TestPowerTransmitter—A Power Transmitter Product designed to analyze and check the
operation of a Power Receiver Product’s wireless power functionality.

 ,(&‹,(&
TestPowerReceiver—A Power Receiver Product designed to analyze and check the operation of
a Power Transmitter Product’s wireless power functionality.
LoadPower—The power dissipated in the Load.

,(&‹,(& 
3 Power Receiver construction
Figure 3 illustrates an example of a functional block diagram for a Baseline Power Profile Power
Receiver.
Figure 3. Functional block diagram for a Baseline Power Profile Power Receiver
Power Pick-up Unit
Rectification
Secondary Coil
circuit
Voltage sense
Communications
Communications
modulator
& Control Unit
Output
disconnect
Load
Sensing & control
In this example, the Power Receiver consists of a Power Pick-up Unit and a Communications and
Control Unit. The Power Pick-up Unit on the left-hand side of Figure 3 comprises the analog
components of the Power Receiver:
ƒ A dual resonant circuit consisting of a Secondary Coil plus series and parallel capacitances to
enhance the power transfer efficiency and enable a resonant detection method (see Section
3.1, Dualresonantcircuit).
ƒ A rectification circuit that provides full-wave rectification of the AC waveform using, for
example, four diodes in a full-bridge configuration or a suitable configuration of active
components (see Section 3.2, Rectificationcircuit). The rectification circuit may perform
output smoothing as well. In this example, the rectification circuit provides power to both the
Communications and Control Unit of the Power Receiver and the output of the Power Receiver.

 ,(&‹,(&
ƒ A communications modulator (see Section 3.4, Communicationsmodulator). On the DC side of
the Power Receiver, the communications modulator typically consists of a resistor in series
with a switch. On the AC side of the Power Receiver, the communications modulator typically
consists of a capacitor in series with a switch (not shown in Figure 3).
ƒ An output disconnect switch, which prevents current from flowing to the output when the
Power Receiver does not provide power at its output. In addition, the output disconnect switch
prevents current back flow into the Power Receiver when the Power Receiver does not provide
power at its output. Moreover, the output disconnect switch minimizes the power that the
Power Receiver draws from the Power Transmitter when a Power Signal is first applied to the
Secondary Coil.
ƒ A rectified voltage sense.
The Communications and Control Unit on the right-hand side of Figure 3 comprises the digital logic
part of the Power Receiver. This unit executes the relevant power control algorithms and protocols,
drives the communications modulator, controls the output disconnect switch, and monitors several
sensing circuits in both the Power Pick-up Unit and the load. (A good example of a sensing circuit in
the load is a circuit that measures the temperature of a rechargeable battery.)
NOTE: This version of the Specification minimizes the set of Power Receiver design requirements defined in
this section. Accordingly, compliant Power Receiver designs that differ from the sample functional
block diagram shown in Figure 3 are possible. For example, an alternative design includes post-
regulation of the output of the rectification circuit (e.g., by using a buck converter, battery charging
circuit, power management unit, etc.). In yet another design, the Communications and Control Unit
interfaces with other subsystems of the Power Receiver Product, e.g. for user interface purposes.
Figure 4 illustrates an example of a functional block diagram for an Extended Power Profile Power
Receiver. The communications demodulator enables the communication of data from the Power
Transmitter to an Extended Power Profile Power Receiver. The presence of a communications
demodulator is the only difference with the functional block diagram of a Baseline Power Profile
Power Receiver.
,(&‹,(& 
Figure 4. Functional block diagram for an Extended Power Profile Power Receiver
Power Pick-up Unit
Rectification
Secondary Coil
circuit
Voltage sense
Communications modulator
Communications
& Control Unit
Communications demodulator
Output
disconnect
Load
Sensing & control
Power Pick-up Unit components are described in the subsections below.
A Power Receiver design shall include a dual resonant circuit as defined in Section 3.1, Dual
resonantcircuit, a rectification circuit as defined in Section 3.2, Rectificationcircuit, sensing circuits
as defined in Section 3.3, Sensingcircuits, a communications modulator as defined in Section 3.4,
Communicationsmodulator, and an output disconnect switch as defined in Section 3.6, Output
disconnect.
A Power Receiver design for the Extended Power Profile shall also include a communications
demodulator as defined in Section 3.5, Communicationsdemodulator, and shall be able to function
meaningfully if the Power Transmitter restrictions limit the output of power from the Power
Receiver to 5 W; see Section 3.7, Shielding.

 ,(&‹,(&
3.1 Dual resonant circuit
The dual resonant circuit of the Power Receiver comprises the Secondary Coil and two resonant
capacitances. The purpose of the first resonant capacitance C is to enhance the power transfer
s
efficiency. The purpose of the second resonant capacitance C is to enable a resonant detection of
d
the receiver position on some Power Transmitter designs.
Figure 5 illustrates the dual resonant circuit. The switch in the dual resonant circuit is optional. If
the switch is not present, the capacitance C shall have a fixed connection to the Secondary Coil L .
d s
If the switch is present, it shall remain closed until the Power Receiver transmits its first Packet
(see the QiSpecification, CommunicationsProtocol).
Figure 5. Dual resonant circuit of a Power Receiver
C
s
C
d
L
s
The dual resonant circuit shall have the following resonant frequencies:
+x
f ′==------------------------------- 100 kHz,
–y
s
2π ⋅ L′ ⋅ C
s s
f==----------------------------------------------------1()000 ±10% kHz.
d
–1
1 1
§·
2π ⋅ L ⋅ ----- + -----
s
©¹
C C
s d
In these equations, L′ is the self-inductance of the Secondary Coil when placed on the Interface
s
Surface of a Power Transmitter and—if necessary—aligned to the Primary Cell; and L is the self-
s
inductance of the Secondary Coil without magnetically active material that is not part of the Power
Receiver design close to the Secondary Coil (e.g. away from the Interface Surface of a Power
Transmitter). Moreover, the tolerances x and y on the resonant frequency f ′ are x = y=5% for
s
Power Receivers that specify a Maximum Power value in the Configuration Packet of 3 W and
above, and x = 5% and y=10% for all other Power Receivers.
NOTE: When determining the capacitance value C , make sure to account for any parasitic capacitances
d
between the terminals of the dual resonant circuit that may affect the resonance frequency value f .
d
The switch shall remain closed even if no power is available from the Secondary Coil.

,(&‹,(& 
The quality factor Q of the loop consisting of the Secondary Coil, switch (if present), resonant
capacitance C and resonant capacitance C , shall exceed the value 77. Here the quality factor Q is
s d
defined as:
2π⋅⋅f L
d s
Q = ------------------------
R
where R is the DC resistance of the loop with the capacitances C and C short-circuited.
s d
Figure 6 shows the environment that is used to determine the self-inductance L′ of the Secondary
s
Coil. The primary Shielding shown in Figure 6 consists of material PC44 from TDK Corp. The
primary Shielding has a square shape with a side of 50 mm and a thickness of 1 mm. The center of
the Secondary Coil and the center of the primary Shielding shall be aligned. The distance from the
Receiver Interface Surface to the primary Shielding is d = 3.4 mm. Shielding on top of the
z
Secondary Coil is present only if the Receiver design includes such Shielding. Other Power Receiver
Product components that influence the inductance of the Secondary Coil shall be present as well
when determining the resonant frequencies. The excitation signal that is used to determine L and
s
L′ shall have an amplitude of 1 V RMS and a frequency of 100 kHz.
s
Figure 6. Characterization of resonant frequencies
Interface
Surface Secondary Coil Shielding (optional)
Mobile
Device
Spacer
d
z
Primary shielding
 ,(&‹,(&
3.2 Rectification circuit
The rectification circuit shall use full-wave rectification to convert the AC waveform to a DC power
level.
3.3 Sensing circuits
The Power Receiver shall monitor the DC voltage V directly at the output of the rectification circuit.
r
3.4 Communications modulator
The Power Receiver shall have the means to modulate the Primary Cell current and Primary Cell
voltage as defined in QiSpecification, CommunicationsPhysicalLayer. This version of the
Specification leaves the specific loading method as a design choice to the Power Receiver. Typical
methods include modulation of a resistive load on the DC side of the Power Receiver and modulation
of a capacitive load on the AC side of the Power Receiver.
3.5 Communications demodulator
For the Extended Power Profile, the Power Receiver shall have the means to demodulate frequency-
shift keying (FSK) data from the Power Signal frequency as defined in QiSpecification,
CommunicationsPhysicalLayer. This Specification leaves the specific method up to the designer of
the Power Receiver.
3.6 Output disconnect
The Power Receiver shall have the means to disconnect its output from the subsystems connected
thereto. If the Power Receiver has disconnected its output, it shall ensure that it still draws a
sufficient amount of power from the Power Transmitter, such that Power Receiver to Power
Transmitter communications remain possible (see QiSpecification, CommunicationsPhysical
Layer).
The Power Receiver shall keep its output disconnected until it reaches the powertransfer phase for
the first time after a Digital Ping (see the QiSpecification, CommunicationsProtocol). Subsequently,
the Power Receiver may operate the output disconnect switch any time while the Power
Transmitter applies a Power Signal.
NOTE: The Power Receiver may experience a voltage peak when operating the output disconnect switch
(and changing between maximum and near-zero power dissipation).
Note that the dual resonant circuit as depicted in Figure 5 (in Section 3.1) does not prohibit
implementation of the communications modulator directly at the Secondary Coil.

,(&‹,(& 
3.7 Shielding
An important consideration for a Power Receiver designer is the impact of the Power Transmitter’s
magnetic field on the Power Receiver Product. Stray magnetic fields could interact with the Power
Receiver Product and potentially cause its intended functionality to deteriorate or cause its
temperature to increase due to the power dissipation of generated eddy currents.
It is recommended to limit the impact of magnetic fields by means of Shielding on the top face of
the Secondary Coil (see the QiSpecification,Mechanical,Thermal,andUserInterface for a diagram
of the secondary coil assembly). This Shielding should consist of material that has parameters
similar to the materials listed in the QiSpecification. The Shielding should cover the Secondary Coil
completely. Additional Shielding beyond the outer diameter of the Secondary Coil might be
necessary depending upon the impact of stray magnetic fields.

 ,(&‹,(&
4 Power Receiver design guidelines (informative)
4.1 Large-signal resonance check
In the course of designing a Power Receiver, it should be verified that the resonance frequencyf of
s
the dual resonant circuit remains within the tolerance range defined in Section 3.1, Dualresonant
circuit, under large-signal conditions. The test defined in this section serves this purpose.
Step 1. Connect an RF power source to the assembly of Secondary Coil, Shielding and other
components that influence the inductance of the Secondary Coil and series resonant capacitance C ;
s
see Figure 7. The presence of the parallel capacitance C is optional.
d
Figure 7. Large signal secondary resonance test
L
s
Vin
I
in
V
out
C
s
C
d
Step 2. Position the assembly and an appropriate spacer on primary Shielding material, as shown
in Figure 5 (in Section 3.1).
Step 3. Measure the input voltage V as a function of the frequency of the RF power source in the
in
range of 90…110 kHz, while maintaining the input current I at a constant level, preferably at about
in
twice the maximum value intended in the final product.
Step 4. Verify that the frequency at which the measured V is at a minimum, occurs within the
in
specified tolerance range of the resonance frequency f .
s
,(&‹,(& 
4.2 Power Receiver coil design
The mutual inductance M of a Secondary Coil, in combination with optional Shielding and other
Power Receiver Product components, and the Primary Coil of a Power Transmitter design A10
should satisfy the following relations:
V
o
ƒ --------- < 0.8 A , if the Primary Coil and Secondary Coil centers are aligned; and
ωM
V
o
---------
ƒ < 1 A , if the Primary Coil and Secondary Coil centers have a lateral offset of 5 ξ 2 mm.
ωM
Here V is the maximum output voltage expected from the Secondary Coil—or any other voltage
o
that the Power Receiver designer considers relevant—and ω = 2πf , with f = 100 kHz, the
frequency at which the mutual inductance (in units of 1 henry) is measured.

 ,(&‹,(&
5 Power Transmitter construction
5.1 Power Transmitter reference designs
The QiSpecification includes a set of Power Transmitter reference designs that were developed,
tested, and certified by member companies of the Wireless Power Consortium.
5.2 Power transfer control
This version of the Specification, defines a specific method, which the Power Transmitter shall use
to control its Primary Cell current towards the new Primary Cell current (see QiSpecification,
CommunicationsProtocol for a description of the power transfer phases). This method is based on
a discrete proportional-integral-differential (PID) algorithm as illustrated in Figure 8.
Figure 8. PID control algorithm
Control error
message
ሺ ሻ
݆ ,݅
ሺ݆ሻ ܲ 
ܿ
ሺ݆െ1ሻ ሺ ሻ
݆ ,݅
ܭή݁ 
ݐ ήቈ1+ ቉
p
a
ሺ݆ሻ
ݐ

d
ሺ݆ ,݅ሻ
+ +
ሺ ሻ
݆ ,݅ ܲܫܦ 
ሺ݆ ,݅ሻ ሺ݆ ,݅ሻ
ሺ݆ ,݅െ1ሻ ܫ 
ሺ݆ ,݅െ1ሻ
݁ ݒ 
ܫ +
 ݒ െ
Power
ȭ ȭ
ሺ݆ ,݅ሻ
ሺ݆ ,݅ሻ
ܭή݁ ήݐ 
i inner    ܵήܲܫܦ  Conversion Unit
+ v
-
+
ሺ݆ ,݅ሻ
ݐ 
a
ሺ ሻ
݆ ,݅െ1 ሺ݆ ,݅െ1ሻ
ܫ  ݒ 

ሺ ሻ
ሺ ሻ ሺ ሻ ݆ ,݅
݆ ,݅ ݆ ,݅െ1
ܦ
݁ െ݁
ܭ ή
d
ݐ
inner
ሺ݆ ,݅െ1ሻ
ݐ 

a
ሺ ሻ
݆ ,݅െ1
݁

ሺ ሻ
݆െ1
ݐ 

a
Transmitter
,(&‹,(& 
To execute this algorithm, the Power Transmitter shall execute the steps listed below, in the order
of appearance. In the definitions of these steps, the index j = 1, 2, 3, … labels the sequence of Control
Error Packets, which the Power Transmitter receives.
th
ƒ Upon receipt of the j Control Error Packet, the Power Transmitter shall calculate the new
()j
Primary Cell current t as
d
()j
()j ()j – 1 c
t = t ⋅ 1 + ---------
d a
()j – 1
where t represents the actual Primary Cell current—reached in response to the previous
a
(j) th
Control Error Packet—and c represents the Control Error Value contained in the j Control Error
()0
Packet. Note that t represents the Primary Cell current at the start of the powertransferphase.
a
(j)
ƒ If the Control Error Value c is non-zero, the Power Transmitter shall adjust its Primary Cell
current during a time window t . For this purpose, the Power Transmitter shall execute a
active
loop comprising of the steps listed below. The index i = 1, 2, 3, … i labels the iterations of this
max
loop.
à The Power Transmitter shall calculate the difference between the new Primary Cell and
the actual Primary Cell current as the error
()ji, ()j ()ji, – 1
e = t – t
d a
()ji, – 1
where t represents the Primary Cell current determined in iteration i Ϋ 1 of the
a
()j, 0
loop. Note that t represents the actual Primary Cell current at the start of the loop.
a
à The Transmitter shall calculate the proportional, integral, and derivative terms (in any
order):
()ji, ()ji,
P = K ⋅ e
p
()ji, ()ji, – 1 ()ji,
I = I + K⋅⋅e t
i inner
()ji, ()ji, – 1
()ji, e – e
D = K ⋅ ---------------------------------
d
t
inner
where K is the proportional gain, K is the integral gain, K is the derivative gain, and t
p i d inner
is the time required to execute a single iteration of the loop. In addition, the integral term
(j,0) (j,0) (j,i)
I = 0, and the error e = 0. The Power Transmitter shall limit the integral term I
such that it remains within the range ΫM … Ϊ M —if necessary, the Power Transmitter
I I
(j,i)
shall replace the calculated integral term I with the appropriate boundary value.

 ,(&‹,(&
à The Power Transmitter shall calculate the sum of the proportional, integral, and derivative
terms:
()ji, ()ji, ()ji, ()ji,
PID = P ++I D .
(j,i)
In this calculation, the
...