EN IEC 63296-2:2024

SLOVENSKI STANDARD
01-december-2024
Prenosna multimedijska oprema - Določanje življenjske dobe baterije - 2. del:
Naglavne in ušesne slušalke s funkcijo aktivnega dušenja hrupa (IEC 63296-
2:2023)
Portable multimedia equipment - Determination of battery duration - Part 2: Headphones
and earphones with active noisecancelling functions (IEC 63296-2:2023)
Tragbare Multimediageräte und -systeme - Bestimmung der Batterielebensdauer - Teil 2:
Kopfhörer und Ohrhörer mit aktiven Funktionen zur Geräuschunterdrückung (IEC 63296
-2:2023)
Matériel multimédia portable – Détermination de la durée des batteries – Partie 2:
Casques et écouteurs avec fonctions de réduction de bruit active (IEC 63296-2:2023)
Ta slovenski standard je istoveten z: EN IEC 63296-2:2024
ICS:
33.160.50 Pribor Accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63296-2

NORME EUROPÉENNE
EUROPÄISCHE NORM January 2024
ICS 33.160.50
English Version
Portable multimedia equipment - Determination of battery
duration - Part 2: Headphones and earphones with active noise-
cancelling functions
(IEC 63296-2:2023)
Matériel multimédia portable - Détermination de la durée Tragbare Multimediageräte und -systeme - Bestimmung der
des batteries - Partie 2: Casques et écouteurs avec Batterielebensdauer - Teil 2: Kopfhörer und Ohrhörer mit
fonctions de réduction de bruit active aktiven Funktionen zur Geräuschunterdrückung
(IEC 63296-2:2023) (IEC 63296-2:2023)
This European Standard was approved by CENELEC on 2024-01-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63296-2:2024 E

European foreword
The text of document 100/4049/FDIS, future edition 1 of IEC 63296-2, prepared by NA "NA" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 63296-2:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-10-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-01-12
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63296-2:2023 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60068-1:2013 NOTE Approved as EN 60068-1:2014 (not modified)
IEC 62087-1:2015 NOTE Approved as EN 62087-1:2016 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60268-1 - Sound system equipment. Part 1: General - -
IEC 60268-7 2010 Sound system equipment - Part 7: EN 60268-7 2011
Headphones and earphones
IEC 60268-24 2023 Sound system equipment - Part 24: EN IEC 60268-24 2024
Headphones and earphones - Active
acoustic noise cancelling characteristics
IEC 60318-4 - Electroacoustics - Simulators of human EN 60318-4 -
head and ear - Part 4: Occluded-ear
simulator for the measurement of
earphones coupled to the ear by means of
ear inserts
IEC 60318-7 - Electroacoustics - Simulators of human EN IEC 60318-7 -
head and ear - Part 7: Head and torso
simulator for the measurement of sound
sources close to the ear
IEC 63296-2 ®
Edition 1.0 2023-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Portable multimedia equipment – Determination of battery duration –

Part 2: Headphones and earphones with active noise-cancelling functions

Matériel multimédia portable – Détermination de la durée des batteries –

Partie 2: Casques et écouteurs avec fonctions de réduction de bruit active

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.160.50  ISBN 978-2-8322-7956-4

– 2 – IEC 63296-2:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Measuring method of battery duration . 8
4.1 General . 8
4.2 Test signal . 8
4.3 Ambient noise signal . 8
4.4 Standard conditions for measurement . 9
4.4.1 General conditions for measurement . 9
4.4.2 Test site . 9
4.5 Test equipment . 9
4.6 Preparation of headphones . 9
4.6.1 Battery to be measured . 9
4.6.2 Input setting. 9
4.7 Test procedure for measurement of battery duration . 10
4.7.1 Adjustment of test signal level . 10
4.7.2 Adjustment of loudness of ambient noise signal . 10
4.7.3 Measurement of battery duration . 10
5 Characteristics to be specified . 10
Annex A (informative) Verification procedure . 11
A.1 General . 11
A.2 Verification procedure . 11
Bibliography . 12

Figure 1 – Example of a battery duration measurement system . 9
Figure A.1 – Flowchart, verification procedure . 11

IEC 63296-2:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PORTABLE MULTIMEDIA EQUIPMENT –
DETERMINATION OF BATTERY DURATION –

Part 2: Headphones and earphones with
active noise-cancelling functions

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 63296-2 has been prepared by technical area 19: Environmental and energy aspects for
multimedia systems and equipment, of IEC technical committee 100: Audio, video and
multimedia systems
...