CEN/TC 286/WG 1 - Design and manufacture of LPG pressure vessels
Design and manufacture of LPG pressure vessels
General Information
This document specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 l up to and including 150 l, exposed to ambient temperature.
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
This document:
— specifies minimum requirements for materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite cylinders with a water capacity from 0,5 litre up to and including 150 litres for liquefied petroleum gases (LPG) exposed to ambient temperatures, with a test pressure of at least 30 bar;
— is only applicable to cylinders which are fitted with a pressure relief valve (see 4.1.3);
— is applicable to cylinders with a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by fibres of glass, carbon or aramid (or a mixture thereof);
— is also applicable to composite cylinders without liners.
Cylinders manufactured to this document are suitable for temperatures down to −40 °C.
This document does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, the choice of material and sleeve performance are expected to be considered separately.
- Standard54 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognized by the Competent Authority.
- LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognized by the Competent Authority.
- Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognized by the Competent Authority.
- LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognized by the Competent Authority.
NOTE 1 All these types of receptacles are referred to throughout this document as “cylinders”.
This document does not specify any requirements for product, hazard or safety-phrase labelling of packaging which can be required to meet ADR or other legislative requirements.
NOTE 2 The marking of cylinders is regulated by RID/ADR which take precedence over any clause in this document. The European Directive on Transportable Pressure Equipment 2010/35/EU [8] includes additional marking requirements (π-marking). For countries that are not members of the European Union, the π marking is replaced by their relevant conformity mark.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This document does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this document, the term "road tanker" is understood to mean "fixed tanks" and "demountable tanks" as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
NOTE 4 This document is intended for LPG only; however, for other liquefied gases see EN 14025.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for the design and manufacture of static welded steel cylindrical pressure vessels, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m3 and for installation above or below ground.
- Standard69 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This document applies only to cylinders having a circular cross-section without any longitudinal joint.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l.
This European Standard applies only to cylinders having a circular cross-section.
Cylinders designed and constructed to the requirements of this European Standard may be over-moulded; additional requirements for these cylinders set out in Annex B.
- Standard50 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard53 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to temperatures of -20 °C to +65 °C. It allows alternative design and construction methods to those required in EN 1442, including coated cylinders, over-moulded cylinders and cylinders for hot air balloons.
This European Standard applies only to pressure receptacles with a circular cross-section.
This European Standard does not include the equipping of the cylinders with valves and other service equipment.
- Standard59 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to temperatures of -20 °C to +65 °C. It allows alternative design and construction methods to those required in EN 1442, including coated cylinders, over-moulded cylinders and cylinders for hot air balloons.
This European Standard applies only to pressure receptacles with a circular cross-section.
This European Standard does not include the equipping of the cylinders with valves and other service equipment.
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1 000 l for Liquefied Petroleum Gases (LPG).
Vertical and horizontal cylindrical receptacles are covered.
- Standard60 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean "fixed tanks" and "demountable tanks" as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 litres up to and including 150 litres, exposed to ambient temperature.
- Draft7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean “fixed tanks” and “demountable tanks” as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252, and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
- Draft4 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker tanks and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover tanks for tank containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean “fixed tanks” and “demountable tanks” as defined in ADR.
NOTE 2 The equipment of the tanks and the inspection and testing after assembly is covered by EN 12252, and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to the approval by the competent authority, as required by ADR.
- Draft12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 litres up to and including 150 litres, exposed to ambient temperature.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard
- specifies minimum requirements for materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite cylinders with a water capacity from 0,5 litre up to and including 150 litres for liquefied petroleum gases (LPG) exposed to ambient temperatures, with a test pressure of at least 30 bar;
- is only applicable to cylinders which are fitted with a pressure relief valve (see 4.1.3);
- is applicable to cylinders with a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by fibres of glass, carbon or aramid (or a mixture thereof);
- is also applicable to composite cylinders without liners.
Cylinders manufactured to this European Standard are suitable for temperatures down to −40 °C.
This European Standard does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, the choice of material and sleeve performance should be considered separately.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard59 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority.
- Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority.
NOTE 1 All these types of receptacles are referred to throughout this standard as "cylinders".
This European Standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements.
NOTE 2 The marking of cylinders is regulated by RID/ADR which take precedence over any clause in this European Standard. The European Directive on Transportable Pressure Equipment 2010/35/EU [9] includes additional marking requirements (-marking).
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean fixed tanks and demountable tanks as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
NOTE 4 This standard is intended for LPG only; however for other liquefied gases see EN 14025.
- Standard66 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design and manufacture of static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m³ and for installation above or below ground.
- Standard + National Annex and/or Foreword66 pagesForeword and/or annex in Slovenian language, body of the standard in English languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section without any longitudinal joint.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
CEN/TC mistake: correction to Formula (D.11)
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean "fixed tanks" and "demountable tanks" as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 litres up to and including 150 litres, exposed to ambient temperature.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to ambient temperatures. It allows alternative design and construction methods to those required in EN 1442.
This European Standard applies only to cylinders with a circular cross-section.
All pressures are gauge unless otherwise stated.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean "fixed tanks" and "demountable tanks" as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
- Standard62 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite cylinders with a water capacity from 0,5 litre up to and including 150 litres for liquefied petroleum gases (LPG) exposed to ambient temperatures, with a test pressure of 30 bar.
This standard is only applicable to cylinders which are fitted with a pressure relief valve (see 4.1.3).
NOTE 1 Cylinders made to this standard are suitable for the temperature range of -40 °C to 50 °C.
This standard is applicable to cylinders with a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by fibres of glass, carbon or aramid (or a mixture thereof).
This standard is also applicable to composite cylinders without liners.
NOTE 2 This standard does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, the choice of material and sleeve performance should be considered separately.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Modification to NOTE Figure F.1
CMC - Modification to E.3 (editorial error)
- Corrigendum2 pagesEnglish and German languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1 000 l for Liquefied Petroleum Gases (LPG).
Vertical and horizontal cylindrical receptacles are covered.
- Standard56 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker tanks and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover tanks for tank containers.
NOTE 1 In the context of this standard the term "road tanker" is understood to mean fixed tanks and demountable tanks as defined in ADR.
NOTE 2 The equipment of the tanks and the inspection and testing after assembly is covered by EN 12252, and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to the approval by the competent authority, as required by ADR.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority.
- Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority.
NOTE All these types of receptacles are referred to throughout this standard as "cylinders".
This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for certain aspects concerning material, design, construction and workmanship, procedure and test at manufacture of transportable refillable welded aluminium LIQUEFIED PETROLEUM GAS cylinders of water capacity from 0,5 l up to and including 150 l exposed to ambient temperatures, and having a single piece with welded cap design as shown in figure 3.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker tanks and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover tanks for ISO type containers.
- Standard61 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
¾ Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority.
LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority.
Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority.
LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority.
NOTE All these types of receptacles are referred to throughout this standard as “cylinders”.
This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
Address/consider technical issues raised during the resolution CEN/TC 286 C05/2001 by France and Belgium.
- Amendment8 pagesEnglish languagesale 10% offe-Library read for1 day
Address/consider technical issues raised during the formal vote process particularly by France and Belgium.
- Amendment12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design and manufacture of static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m³ and for installation underground.
- Standard55 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for the design and manufacture of static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m3 and for installation above ground.
- Standard52 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements concerning material, design, construction and workmanship, procedure and test at manufacture of transportable refillable brazed steel liquefied petroleum gas (LPG) cylinders of water capacity from 0,5 l up to and including 15 l. The limit of 15 l is related to manufacturing process available.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker tanks and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This standard does not cover tanks for ISO type containers.
- Standard59 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to ambient temperatures. It allows alternative design and construction methods to those required in EN 1442.
This European Standard applies only to cylinders with a circular cross-section.
All pressures are gauge unless otherwise stated.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
To amend annex A to align it with the current regulations
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements concerning material, design, construction and workmanship, procedure and test at manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders of water capacity from 0,5 l up to and including 150 l exposed to ambient temperatures.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day