EN IEC 60938-2:2021
(Main)Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification on power line chokes
Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification on power line chokes
This part of IEC 60938 applies to fixed inductors designed for electromagnetic interference suppression, which will be connected to an AC mains or other supply with a nominal voltage not exceeding 1 000 V AC RMS or 1 500 V DC with a nominal frequency not exceeding 400 Hz. This sectional specification is restricted to fixed inductors for which safety tests are appropriate. This implies that inductors specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Annex A is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. The object of this document is to prescribe standard requirements for safety tests, preferred ratings and characteristics, to select from IEC 60938-1 the appropriate methods of test and to give general performance requirements for suppression inductors.
Drosseln zur Unterdrückung elektromagnetischer Störungen – Teil 2: Rahmenspezifikation zu Netzdrosseln
Inductances fixes d'antiparasitage - Partie 2: Spécification intermédiaire sur les bobines d’arrêt pour ligne électrique
L'IEC 60938-2:2021 s'applique à des inductances fixes conçues pour s’opposer aux perturbations électromagnétiques, qui sont connectées à un réseau d’alimentation à courant alternatif ou à une autre source d’alimentation dont la tension nominale ne dépasse pas 1 000 V (valeur eff.) en courant alternatif ou 1 500 V en courant continu avec une fréquence nominale qui ne dépasse pas 400 Hz. La présente spécification intermédiaire se limite à des inductances fixes pour lesquelles des essais de sécurité sont souhaitables. Cela signifie que les inductances décrites conformément à la présente spécification sont, soit reliées à l'alimentation secteur, lorsque la conformité aux essais obligatoires de l’Annexe A est nécessaire, soit utilisées en d'autres positions du circuit pour lesquelles la spécification applicable à l'équipement indique que certains ou l'ensemble de ces essais de sécurité sont exigés. Le présent document a pour objet de prescrire des exigences normalisées d'essais de sécurité ainsi que des valeurs assignées et caractéristiques préférentielles, qui permettent de choisir à partir de l’IEC 60938-1 les méthodes d'essai appropriées et de fournir des exigences générales de performance applicables aux inductances d'antiparasitage. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente. - le programme d’essai pour les essais de performance a été supprimé; les essais de sécurité obligatoires et les essais de performance facultatifs sont énumérés dans un seul programme d’essai à l’Annexe B; - les exigences relatives aux bobines d’arrêt à thyristor ont été supprimées; - les exigences relatives aux matériaux sont alignées sur les normes IEC 60939-3 et UL 60939-3; - les bobines d’arrêt à courant alternatif d’une tension jusqu’à 1 000 V et les bobines d’arrêt à courant continu d’une tension jusqu’à 1 500 V sont désormais incluses dans le Domaine d’application.
Fiksne dušilke za dušenje elektromagnetnega motenja - 2. del: Področna specifikacija za električne dušilke (IEC 60938-2:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2021
Nadomešča:
SIST EN 60938-2:2002
SIST EN 60938-2:2002/A1:2007
Fiksne dušilke za dušenje elektromagnetnega motenja - 2. del: Področna
specifikacija za električne dušilke (IEC 60938-2:2021)
Fixed inductors for electromagnetic interference suppression - Part 2: Sectional
specification on power line chokes (IEC 60938-2:2021)
Drosseln zur Unterdrückung elektromagnetischer Störungen – Teil 2:
Rahmenspezifikation zu Netzdrosseln (IEC 60938-2:2021)
Inductances fixes d'antiparasitage - Partie 2: Spécification intermédiaire sur les bobines
d’arrêt pour ligne électrique (IEC 60938-2:2021)
Ta slovenski standard je istoveten z: EN IEC 60938-2:2021
ICS:
29.180 Transformatorji. Dušilke Transformers. Reactors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60938-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2021
ICS 29.100.10; 31.020 Supersedes EN 60938-2:1999 and all of its amendments
and corrigenda (if any)
English Version
Fixed inductors for electromagnetic interference suppression -
Part 2: Sectional specification on power line chokes
(IEC 60938-2:2021)
Inductances fixes d'antiparasitage - Partie 2: Spécification Drosseln zur Unterdrückung elektromagnetischer
intermédiaire sur les bobines d'arrêt pour ligne électrique Störungen - Teil 2: Rahmenspezifikation zu Netzdrosseln
(IEC 60938-2:2021) (IEC 60938-2:2021)
This European Standard was approved by CENELEC on 2021-08-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60938-2:2021 E
European foreword
The text of document 40/2846/FDIS, future edition 3 of IEC 60938-2, prepared by IEC/TC 40
“Capacitors and resistors for electronic equipment” was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60938-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–05–24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–08–24
document have to be withdrawn
This document supersedes EN 60938-2:1999 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60938-2:2021 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60063 NOTE Harmonized as EN 60063
IEC 60068-2-1 NOTE Harmonized as EN 60068-2-1
IEC 60068-2-2 NOTE Harmonized as EN 60068-2-2
IEC 60068-2-6 NOTE Harmonized as EN 60068-2-6
IEC 60068-2-20 NOTE Harmonized as EN IEC 60068-2-20
IEC 60068-2-27 NOTE Harmonized as EN 60068-2-27
IEC 60068-2-30 NOTE Harmonized as EN 60068-2-30
IEC 60068-2-58 NOTE Harmonized as EN 60068-2-58
IEC 60068-2-78 NOTE Harmonized as EN 60068-2-78
IEC 60938-2-1 NOTE Harmonized as EN 60938-2-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60027 series Letters symbols to be used in electrical - -
technology
IEC 60050 series International Electrotechnical Vocabulary - -
(IEV)
IEC 60060-1 - High-voltage test techniques - Part 1: EN 60060-1 -
General definitions and test requirements
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60068-2-13 - Environmental testing - Part 2–13: Tests - EN IEC 60068-2-13 -
Test M: Low air pressure
IEC 60068-2-14 - Environmental testing - Part 2–14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-17 - Basic environmental testing procedures - EN 60068-2-17 -
Part 2–17: Tests - Test Q: Sealing
IEC 60068-2-21 - Environmental testing - Part 2–21: Tests - - -
Test U: Robustness of terminations and
integral mounting devices
IEC 60068-2-45 - Basic environmental testing procedures - EN 60068-2-45 -
Part 2–45: Tests - Test XA and guidance:
Immersion in cleaning solvents
IEC 60317-0-7 - Specifications for particular types of EN 60317-0-7 -
winding wires - Part 0–7: General
requirements - Fully insulated (FIW) zero-
defect enamelled round copper wire
IEC 60317-56 - Specifications for particular types of EN 60317-56 -
winding wires – Part 56: Solderable fully
insulated (FIW) zero-defect polyurethane
enamelled round copper wire, class 180
IEC 60335-1 - Household and similar electrical appliances - -
- Safety - Part 1: General requirements
IEC 60617 - Graphical symbols for diagrams - -
IEC 60664-1 - Insulation coordination for equipment EN IEC 60664-1 -
within low-voltage supply systems - Part 1:
Principles, requirements and tests
IEC 60695-2-11 - Fire hazard testing - Part 2–11: EN 60695-2-11 -
Glowing/hot-wire based test methods -
Glow-wire flammability test method for end
products (GWEPT)
IEC 60695-2-12 - Fire hazard testing - Part 2–12: EN 60695-2-12 -
Glowing/hot-wire based test methods -
Glow-wire flammability index (GWFI) test
method for materials
IEC 60695-2-13 - Fire hazard testing - Part 2–13: EN 60695-2-13 -
Glowing/hot-wire based test methods -
Glow-wire ignition temperature (GWIT) test
method for materials
IEC 60695-10-2 - Fire hazard testing - Part 10–2: Abnormal EN 60695-10-2 -
heat - Ball pressure test method
IEC 60695-11-10 - Fire hazard testing - Part 11–10: Test EN 60695-11-10 -
flames - 50 W horizontal and vertical flame
test methods
IEC 60695-11-20 - Fire hazard testing - Part 11–20: Test EN 60695-11-20 -
flames - 500 W flame test method
IEC 60851-5 - Winding wires - Test methods - Part 5: EN 60851-5 -
Electrical properties
IEC 60938-1 2021 Fixed inductors for electromagnetic EN IEC 60938-1 2021
interference suppression - Part 1: Generic
specification
IEC 60938-2-2 - Fixed inductors for electromagnetic EN 60938-2-2 -
interference suppression - Part 2–2: Blank
detail specification - Inductors for which
safety tests are required (only)
CISPR 17 - Methods of measurement of the EN 55017 -
suppression characteristics of passive
EMC filtering devices
ISO 80000-6 - Quantities and units - Part 6:
Electromagnetism
IEC 60938-2 ®
Edition 3.0 2021-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed inductors for electromagnetic interference suppression –
Part 2: Sectional specification on power line chokes
Inductances fixes d’antiparasitage –
Partie 2: Spécification intermédiaire sur les bobines d’arrêt pour ligne électrique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.100.10; 31.020 ISBN 978-2-8322-1002-2
– 2 – IEC 60938-2:2021 © IEC 2021
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General requirements . 9
4.1 General . 9
4.2 Preferred values of ratings and characteristics . 9
4.2.1 Climatic categories . 9
4.2.2 Nominal inductance and tolerance . 9
4.2.3 Rated voltage U . 9
R
4.2.4 Rated temperature T . 9
r
4.2.5 Rated current I . 10
r
4.3 Information to be given in a detail specification . 10
4.3.1 General . 10
4.3.2 Outline drawing and dimensions . 10
4.3.3 Mounting . 11
4.3.4 Ratings and characteristics . 11
4.4 Insulated inductors for power line applications . 11
4.5 Marking . 11
5 Safety tests for approval . 12
5.1 General . 12
5.1.1 Approval on the basis of the fixed sample size procedures . 12
5.1.2 Structurally similar inductors . 12
5.1.3 Sampling . 13
5.2 Standard atmospheric conditions . 13
5.3 Visual examination . 13
5.3.1 Dimensions (gauging) . 13
5.3.2 Dimensions (detail) . 13
5.4 Insulation resistance . 14
5.5 Voltage test . 14
5.6 Inductance . 15
5.7 Line resistance . 15
5.8 Insertion loss (optional) . 15
5.9 Temperature rise (applies to inductors with a mass > 5 g only) . 15
5.9.1 General . 15
5.9.2 Test method . 15
5.9.3 Requirements . 16
5.10 Impulse voltage (applies to inductors with more than one winding only) . 16
5.10.1 Test conditions .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.