This document specifies a method for determining the apparent axial long-term modulus of pipes subject to beam bending deflection between vertically supported end-couplers, which allow rotation of the pipe relative to the couplers. In conjunction with ISO 10928, this document expresses the results of the test as an apparent axial long-term modulus for use in the calculation of mid-span beam deflection and end rotation of GRP pipes as specified in ISO/TS 10986. Test conditions and requirements ar...view more

    • sale 15% off
    • Standard
      7 pages
      English language
    • sale 15% off
    • Draft
      7 pages
      English language

This document specifies methods of test for joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals, for buried and above-ground glass-reinforced thermosetting plastics (GRP) piping systems. It covers methods of testing for leaktightness and resistance to damage of the joint only, when subjected to specified combinations of angular movement, compression (deformation) perpendicular to the pipe axis and internal pressure. It assumes that the joint will be...view more

    • sale 15% off
    • Standard
      15 pages
      English language
    • sale 15% off
    • Draft
      15 pages
      English language

This document specifies a method for testing the ability of glass-reinforced thermosetting plastics (GRP) pipes to withstand specified levels of initial ring deflection without displaying surface damage and/or structural failure.

    • sale 15% off
    • Standard
      7 pages
      English language
    • sale 15% off
    • Draft
      7 pages
      English language

This document specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittings in a deflected condition for nominal sizes DNÂ 100 and larger. In conjunction with ISOÂ 10928, this document provides a method for evaluating the effect of a chemical environment on the interior of a pipe or fitting after a specified period of time. Test conditions and requirements are specified in the referring International Standard. ISOÂ 23856...view more

    • sale 15% off
    • Standard
      9 pages
      English language
    • sale 15% off
    • Draft
      9 pages
      English language

This document specifies six test methods for the determination of the initial circumferential tensile wall strength per unit of length of glass-reinforced thermosetting plastics (GRP) pipes. NOTE Another commonly used term for "circumferential tensile strength" is "hoop tensile strength" and the two expressions can be used interchangeably. The burst test (method A) is suitable for all types and sizes of pipes. It is considered the reference method. However, all the methods in this document have ...view more

    • sale 15% off
    • Standard
      20 pages
      English language
    • sale 15% off
    • Draft
      20 pages
      English language

This document specifies methods of test for bolted flange joints for buried and above-ground glass-reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to bolted flange joints intended to be used in buried or above-ground applica...view more

    • sale 15% off
    • Standard
      17 pages
      English language

This document specifies methods of test for cemented or wrapped joints for buried and above ground glass-reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to cemented or wrapped joints intended to be used in buried or above-gr...view more

    • sale 15% off
    • Standard
      15 pages
      English language

This document specifies methods for determining the initial ring stiffness of glass-reinforced thermosetting plastics (GRP) pipes. Two methods are given (constant load and constant deflection), and within the specified deflection limits, each is equally valid and can be used for any diameter.

    • sale 15% off
    • Standard
      8 pages
      English language

This document specifies methods of test for joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals, for buried and above ground glass-reinforced thermosetting plastics (GRP) piping systems. It covers methods of test for leaktightness and resistance to damage of the joint only, when subjected to specified combinations of angular movement, compression (deformation) perpendicular to the pipe axis and internal pressure. It assumes that the joint will be ex...view more

    • sale 15% off
    • Standard
      12 pages
      English language

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of drainage and sewerage with or without pressure. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations. NOTE 1 For the purpose of this document, the term polyester r...view more

    • sale 15% off
    • Standard
      59 pages
      English language

This document specifies a method for determining by extrapolation the long-term ultimate ring bending strain and the calculation of the long-term ultimate relative ring deflection of glass-reinforced thermosetting plastics (GRP) pipes, under wet conditions. Two methods of loading are given, one using plates the other beam bars.

    • sale 15% off
    • Standard
      10 pages
      English language

This document specifies methods for determining the ring creep properties for glass-reinforced thermosetting plastics (GRP) pipes. Properties include the creep factor and the long-term specific creep stiffness. Testing is performed under either wet (total immersion in water) or dry conditions. Dry creep testing is typically performed for the assessment and control of raw material consistency. Wet creep testing is typically undertaken to determine the long-term creep performance in simulated use ...view more

    • sale 15% off
    • Standard
      9 pages
      English language

ISO 10639:2017 specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply with or without pressure, including, but not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. ISO 10639:2017 is applicable to GRP UP piping systems, with flexible or rigi...view more

    • sale 15% off
    • Standard
      57 pages
      English language

ISO/TS 12512:2017 specifies a method for determining the initial specific ring stiffness of pipes having a nominal size of DN 2000 or larger, using segment test pieces cut from a glass-reinforced thermosetting plastics (GRP) pipe.

    • sale 15% off
    • Technical specification
      20 pages
      English language

ISO 7510:2017 specifies a method for the determination of constituent materials of a test sample cut from a glass-reinforced plastics (GRP) component intended for use in a piping system. It includes determination of resin, glass, aggregate and filler contents. It is also applicable to the determination of the type and arrangement of the reinforcements. If used to determine the amounts of constituent materials in layered constructions it may be necessary to separate the laminate layers by cutting...view more

    • sale 15% off
    • Standard
      5 pages
      English language

ISO 16611:2017 specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage without pressure including culverts. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. ISO 16611:2017 i...view more

    • sale 15% off
    • Standard
      25 pages
      English language

ISO/TS 20656-1:2017 describes how partial factors for buried GRP pipes are developed, and are primarily intended to define the necessary safety measures for GRP pipes that meet the requirements of ISO 10639, ISO 10467 and ISO 25780, and EN 1796 and EN 14364. The same methodology can be utilised for other pipe product standards, although other parameters would apply.

    • sale 15% off
    • Technical specification
      24 pages
      English language

ISO 10928:2016 specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with the test methods and referring standards for glass-reinforced thermosetting plastics (GRP) pipes or fittings for the analysis of properties as a function of time. However, it can be used for the analysis of other data. Depending upon the nature of the data, two methods are specified. The extrapolation...view more

    • sale 15% off
    • Standard
      47 pages
      English language
    • sale 15% off
    • Standard
      47 pages
      English language

ISO 8639:2016 specifies test methods for flexible non-thrust resistant socket-and-spigot joints with elastomeric sealing elements for buried and above ground glass-reinforced thermosetting plastics (GRP) pipeline applications. It covers methods of test for the leaktightness and resistance to damage of the joint only, when subject to specified combinations of longitudinal extension (draw), angular movement (angular deflection), compression (deformation) perpendicular to the pipe axis and internal...view more

    • sale 15% off
    • Standard
      9 pages
      English language
    • sale 15% off
    • Standard
      9 pages
      English language

ISO 8513:2016 specifies two test methods for determining the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes. The properties which can be determined are - the longitudinal tensile strength, and - the percentage ultimate elongation. Method A uses, for the test piece(s), a longitudinal strip cut from a pipe. Method B uses a specified length of the full cross-section of the pipe. Method A is applicable to pipes with a nominal size of DN 50 or greater with circ...view more

    • sale 15% off
    • Standard
      11 pages
      English language

ISO 18851:2015 specifies methods of test for fittings of any form, i.e. bends, branches, tapers, intended to be used in plastics piping systems for pressure and non-pressure drainage and sewerage or water supply made of glass-reinforced thermosetting plastics (GRP). It is applicable to fittings, in order to test their structural design, but is not applicable to connecting joint systems. It assumes that the fitting either is or is not intended to be subject to the effects of hydrostatic end thrus...view more

    • sale 15% off
    • Standard
      7 pages
      English language

ISO 7509:2015 specifies a method for determining the time-to-failure of glass-reinforced thermosetting plastics (GRP) pipes under internal hydrostatic pressure at a specified temperature. The external environment can be air or water. NOTE For other internal or external environments, the referring standard is to specify any additional requirement.

    • sale 15% off
    • Standard
      7 pages
      English language

ISO 10952:2014 specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittings in a deflected condition for nominal sizes DN 100 and larger. In conjunction with ISO 10928, ISO 10952:2014 provides a method for evaluating the effect of a chemical environment on the interior of a pipe or fitting after a specified period of time. Test conditions and requirements are specified in the referring International Standard. ISO 10467 ...view more

    • sale 15% off
    • Standard
      8 pages
      English language

ISO 25780:2011 specifies the properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for water supply, irrigation, drainage or sewerage systems with or without pressure. ISO 25780:2011 is applicable to GRP-UP piping systems, with flexible joints, intended to be installed using jacking techniques. It specifies the characteristics of pipes made from GRP-UP, with or without aggregates or fillers and also sp...view more

    • sale 15% off
    • Standard
      51 pages
      English language

ISO 18672-1:2009 specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking for pipes and fittings made from polyester resin concrete (PRC), intended to be used within a drain or sewer system operating without pressure. It applies to products for use in buried installations to be installed by open-trench techniques or pipe jacking. It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross...view more

    • sale 15% off
    • Standard
      68 pages
      English language

ISO 10465-3:2007 gives supplementary information on parameters and application limits for the underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP). It is particularly relevant when using an ATV-A 127 type design system. Explanations for the long-term safety factors incorporated into the GRP system standards based on simplified probabilistic methods are provided in an annex.

    • sale 15% off
    • Technical report
      63 pages
      English language

ISO/TR 10465-2:2007 presents a comparison of the ATV and AWWA methods for static calculations on underground GRP pipe installations. It is intended that this comparison will encourage the use of both procedures for GRP pipes conforming to International Standards. It is not the intent of ISO/TR 10465-2 to cover all the details of the two methods. Some aspects are, of necessity, very complex, and for a full understanding the original documents need to be studied in detail. Rather, the intention is...view more

    • sale 15% off
    • Technical report
      36 pages
      English language

ISO/TS 10465-1:2007 describes the procedures for underground installation of flexible glass-reinforced thermosetting resin (GRP) pipes. It refers generally to GRP pipes as specified in the system standards ISO 10467 and ISO 10639, but it can also be used as a guide for the installation of other GRP pipes. It does not include jacking, relining or above-ground installations; nor does it cover health and safety or environmental conditions, these being addressed in national regulations at the place ...view more

    • sale 15% off
    • Technical specification
      45 pages
      English language
    • sale 15% off
    • Draft
      60 pages
      English language
    • sale 15% off
    • Draft
      60 pages
      English language
    • sale 15% off
    • Draft
      62 pages
      French language
    • sale 15% off
    • Draft
      61 pages
      French language

ISO 15306:2003 specifies a method for determining the resistance of glass-reinforced thermosetting plastics (GRP) pipes to cyclic internal pressure. Whilst the standard refers to pipes, the procedure described can also be applied to fittings.

    • sale 15% off
    • Standard
      5 pages
      English language

This International Standard specifies two test methods, designated method A and method B, for checking the leaktightness of glass-reinforced thermosetting plastics (GRP) pipes and fittings under short-term internal pressure. Method A is a hydraulic test applicable to a pipe under uniaxial stress. Method B is a pneumatic test applicable to fittings. NOTE Test methods for the leaktightness of joints or for the resistance of the pipe to long-term hydrostatic pressure are covered by other standards.

    • sale 15% off
    • Standard
      4 pages
      English language

ISO 8513:2014 specifies three test methods for determining the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes. The properties which can be determined are: the longitudinal tensile strength and the percentage ultimate elongation. Method A uses, for the test piece(s), a longitudinal strip cut from a pipe. Method B uses a specified length of the full cross-section of the pipe. Method C uses a notched plate cut from a pipe wall section. Method A is applicable ...view more

    • sale 15% off
    • Standard
      16 pages
      English language
    • sale 15% off
    • Standard
      3 pages
      English language
    • sale 15% off
    • Standard
      2 pages
      English language
    • sale 15% off
    • Standard
      5 pages
      English language
    • sale 15% off
    • Standard
      2 pages
      English language
    • sale 15% off
    • Standard
      4 pages
      English language
    • sale 15% off
    • Standard
      1 page
      English language
    • sale 15% off
    • Standard
      1 page
      English language
    • sale 15% off
    • Standard
      1 page
      English language

ISO 10928:2009 specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with the test methods and referring standards for glass-reinforced thermosetting plastics (GRP) pipes or fittings for the analysis of properties as a function of time. However, it can be used for the analysis of other data. Depending upon the nature of the data, two methods are specified. The extrapolation...view more

    • sale 15% off
    • Standard
      51 pages
      English language

ISO 8521:2009 specifies six test methods for the determination of the initial circumferential tensile wall strength per unit of length of glass-reinforced thermosetting plastics (GRP) pipes. NOTE Another commonly used term for “circumferential tensile strength” is “hoop tensile strength” and the two expressions can be used interchangeably. The burst test (method A) is suitable for all types and sizes of pipes. It is considered the reference method. However, all the methods in ISO 8521:2009 have ...view more

    • sale 15% off
    • Standard
      18 pages
      English language

ISO 10952:2008 specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittings in a deflected condition for nominal sizes DN 100 and larger. In conjunction with ISO 10928, ISO 10952:2008 provides a method for evaluating the effect of a chemical environment on the interior of a pipe or fitting after a specified period of time. Test conditions and requirements are specified in the referring standards such as ISO 10467.

    • sale 15% off
    • Standard
      9 pages
      English language

ISO 10467:2004 specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for drainage or sewerage with or without pressure, as well as the properties of the system itself. It is applicable to GRP-UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in buried installations. It is applicable to pipes, fittings and their joints of no...view more

    • sale 15% off
    • Standard
      75 pages
      English language

ISO 10639:2004 specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for water supply with or without pressure, as well as the properties of the system itself. It is applicable to GRP-UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in buried installations. It is applicable to pipes, fittings and their joints of nominal si...view more

    • sale 15% off
    • Standard
      72 pages
      English language

ISO 14828:2003 specifies a method for determining both the long-term specific ring relaxation stiffness and the wet relaxation factor for glass-reinforced thermosetting plastics (GRP) pipes.

    • sale 15% off
    • Standard
      10 pages
      English language

ISO 8533:2003 specifies methods of test for cemented or wrapped joints for plastics piping systems made of glass-reinforced thermosetting plastics (GRP) for buried and non-buried pipelines. This standard is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests are applicable to cemented or wrapped joints intended to be used in either buried or non-buried...view more

    • sale 15% off
    • Standard
      9 pages
      English language

ISO 10468:2003 specifies a method for determining both the long-term specific ring creep stiffness and the wet creep factor for glass-reinforced thermosetting plastics (GRP) pipes.

    • sale 15% off
    • Standard
      10 pages
      English language

ISO 10471:2003 specifies a method for determining by extrapolation the long-term ultimate bending strain and the calculation of the long-term ultimate relative ring deflection of glass-reinforced thermosetting plastics (GRP) pipes, under wet conditions. Two methods of loading are given, one using plates the other beam bars. Either method may be used for measurements of relative vertical deflection up to 28 %. When it is expected that this level is going to be exceeded then the procedure is limit...view more

    • sale 15% off
    • Standard
      10 pages
      English language