ISO 10639:2004/Amd 1:2011

INTERNATIONAL ISO
STANDARD 10639
First edition
2004-02-01
AMENDMENT 1
2011-03-01


Plastics piping systems for pressure and
non-pressure water supply — Glass-
reinforced thermosetting plastics (GRP)
systems based on unsaturated polyester
(UP) resin
AMENDMENT 1
Systèmes de canalisation en matières plastiques pour l'alimentation en
eau avec ou sans pression — Systèmes en plastiques
thermodurcissables renforcés de verre (PRV) à base de résine de
polyester non saturé (UP)
AMENDEMENT 1




Reference number
ISO 10639:2004/Amd.1:2011(E)
©
ISO 2011

---------------------- Page: 1 ----------------------
ISO 10639:2004/Amd.1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10639:2004/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 10639:2004 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings
and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all
applications.

© ISO 2011 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 10639:2004/Amd.1:2011(E)
Plastics piping systems for pressure and non-pressure water
supply — Glass-reinforced thermosetting plastics (GRP)
systems based on unsaturated polyester (UP) resin
AMENDMENT 1
Page 1, Scope
Add the following Note after the first paragraph and renumber other note as Note 2:
NOTE 1 For the purpose of this International Standard, the term polyester resin also includes vinyl-ester resins.
Pages 2 and 3, Normative references
Correct the following dated Normative references into undated references:
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 7432, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the
design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
ISO 7511, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test
methods to prove the leaktightness of the wall under short-term internal pressure
ISO 8483, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test method to prove the
design of bolted flange joints
ISO 8513, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of
longitudinal tensile properties
ISO 8521, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods
for the determination of apparent initial circumferential tensile strength
ISO 8533, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the
design of cemented or wrapped joint
ISO 8639, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness
of flexible joints
ISO 10928, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings —
Methods for regression analysis and their use
Page 16, 4.5.1
Add the following paragraph after the first paragraph:
For routine quality control testing, any measurements shall be taken at the prevailing temperature or, if the
manufacturer requires, at the temperature specified in this clause.
© ISO 2011 – All rights reserved 1

...