CEN/TC 132/WG 7 - Sheets, strips and plates

This document specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm.
It is applicable to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip.
It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.
It applies to:
—   circles made out of hot or cold rolled circles stock by:
•   blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
•   sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
—   hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards.

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This document is applicable to:
—   circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm;
NOTE   Circles with a diameter up to 1 000 mm can be produced by blanking.
—   hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European Standards.

This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573 3. Temper designations are defined in EN 515.

This European Standard specifies the technical delivery conditions relating to armour plates in weldable aluminium alloy with a nominal thickness between 10 mm and 70 mm.
For thickness below 10 mm, other specifications may be applied.

This European Standard establishes temper designations for all forms of wrought aluminium and aluminium alloys and for continuously cast aluminium and aluminium alloys drawing stock and strip intended to be wrought.
NOTE   Some of these temper designations may be subject of patent or patent applications and their listing herein is not to be construed in any way as the granting of a license under such patent right.
Additional temper designations, conforming to this standard, may be standardized with CEN/TC 132 and AECMA/5 provided:
-   the temper is used or is available for use by more than one user;
-   mechanical property limits are defined;
-   the characteristics of the temper are significantly different from those of all other tempers which have the same sequence of basic treatments and for which designations already have been assigned for the same alloy and product;
-   the following are also defined if characteristics other than mechanical properties are considered significant:
a)   test methods and limits for the characteristics; or
b)   the specific practices used to produce the temper.

This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where different or additional requirements are formulated and the appropriate alloys and tempers are selected: see Annex A. Most of these special European Standards refer to provisions of this document.
The selection of the relevant special European Standards is under the responsibility of the purchaser.
Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue strength, surface appearance and welding properties, the user should consult the supplier and consider the relevant special European Standard, as applicable.

This Technical Report presents the characteristics of reference dies and reference castings, to be used for evaluating the mechanical potential (in terms of Ultimate Tensile Strength, Yield Strength and Elongation) which can be expected by Al-Si based alloys, cast by high pressure, low pressure and gravity (permanent mould) processes. These properties are measured on separately cast test specimens produced with state-of-the-art knowledge on die design, process management and alloy treatments correctly applied to minimize defects and imperfections.

This Technical Report specifies the classification of the defects and imperfections may be present in cast products manufactured by high pressure, low pressure and gravity die casting of aluminium alloys.

This European Standard specifies the technical conditions for inspection and delivery, the mechanical properties and
electrical conductivity of wrought aluminium sheet, strip and plate for electrotechnical applications such as bus bars
and other conductors, products requiring a certain minimum electrical conductivity.
It applies to products with a thickness over 0,20 mm up to and including 150 mm.

This document specifies the technical conditions of inspection and delivery, the mechanical properties, the tolerances on dimensions and form of rolled semi-finished aluminium alloy products intended for tanks for the storage and transportation of dangerous goods, in particular of gasoline and other liquid hydrocarbons.
It applies to hot or cold-rolled strip, sheet and plate with a thickness from 3,0 mm and up to and including 12,0 mm used as a wall material.
NOTE   Compliance with the present document does not ensure compliance with national or international regulations. The user of the document is responsible for checking that the material he orders or sells complies with all applicable regulations. Depending on the chemical and physical properties of the dangerous good to be transported or stored, it can be necessary to agree on additional properties or inspection conditions in order to comply with applying regulations.

This document specifies the codification of some standardized semifinished wrought products for use in ordering information.
NOTE   Codification is usually required for technical drawings.
It does not apply to castings, cast forging stock, rolling ingots, extrusion billets and ingots for remelting.

This document specifies the technical conditions of inspection and delivery, the mechanical properties, the tolerances on dimensions and form of rolled semi-finished aluminium alloy products intended for floor plating, e.g. in vehicle construction, shipbuilding and metallic structures with a raised pattern on one side and a smooth surface on the other side.
It applies to sheets, strips and plates from 1,2 mm up to 20 mm in thickness and up to and including 2 500 mm in width, and to sheets and plates up to 14 000 mm in length.

This document specifies the technical conditions for inspection and delivery, mechanical properties, dimensional tolerances and other requirements for rolled products made from wrought aluminium and wrought aluminium alloys with thicknesses from 0,150 mm to 0,500 mm for manufacturing rigid cans, closures, lids and tabs.

This document specifies a European designation system of wrought aluminium and aluminium alloys, based on an international designation system, and the procedure to obtain such international designation.
It is in accordance with the "Recommendation" dated December 15, 1970, as revised in March 2002, for an International Designation System for Wrought Aluminum and Wrought Aluminum Alloys issued by the Aluminum Association, Washington DC 20006, USA.
This standard applies to wrought products and to ingots intended to be wrought.

This European Standard specifies additional requirements on the chemical composition of aluminium and aluminium alloys intended for the manufacture of packaging and packaging components, as well as related specific technical conditions of inspection and delivery. The scope of this standard is fully defined by the final application.
NOTE   Some of the products listed in the present standard can be subject to patent or patent applications, and their listing herein does not in any way imply the granting of a licence under such patent right.
CEN/TC 132 affirms it is policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.

This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by hot-rolling, for general engineering applications. It applies to products with a thickness from 2,5 mm up to and including 400 mm. It does not apply to semi-finished rolled produits in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, ect., sheet and strip or to special applications such as aerospace which are dealt with in separate European Standards.

This part of EN 12482 specifies the particular requirements for wrought aluminium and aluminium alloys in the form of hot rolled strip. The thickness range covered is from 2,0 mm to 12 mm.  It does not apply to hot-rolled strip which are not rerolled such as strip for general engineering or special applications.

This part of prEN 12482 specifies the particular requirements for wrought aluminium and aluminium alloys in the form of hot rolled strip. The thickness range covered is over 0,20 mm to 4 mm. It does not apply to cold rolled strip which are not rerolled such as strip for general engineering or special applications.

This standard specifies the method for determining the ear height of sheet and strip of nominal thicknesses from 0,08 mm to 6 mm after deep drawing.

This Part of EN 573 specifies a code of designation applicable to aluminium and aluminium alloys as specified in the relevant European Standards. It is a descriptive code based primarily on chemical symbols. The designations in accordance with this Part of EN 573 are intended primarily as a supplement to the four figure designation described in EN 573-1. This standard applies to wrought products and to ingots intended to be wrought.

This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheets, strips and plates obtained by cold-rolling, for general engineering applications. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, etc. sheets and strips or to special applications such as aerospace, can stock, etc. which are dealt with in separate European standards. Technical conditions for inspection and delivery of those products are specified in EN 485-1.

This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3. Temper designations are defined in EN 515.

This European Standard specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm.
It applies to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip.
It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.
It applies to:
-   Circles made out of hot or cold rolled circles stock by:
-   Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
-   Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
-   Hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards.

This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This standard is applicable to:
-   Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm.
NOTE   Circles with a diameter up to 1 000 mm can be produced by blanking.
-   Hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This European Standard is not applicable to slugs for impact extrusions which are dealt with in other European Standards.

This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573 3. Temper designations are defined in EN 515.

This European Standard establishes temper designation for all forms of wrought aluminium and aluminium alloys and to continuously cast aluminium alloy drawing stock and strip intended to be wrought.

This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where different or additional requirements are formulated and the appropriate alloys and tempers are selected: see Annex A. Most of these special European Standards refer to provisions of this document.
The selection of the relevant special European Standards is under the responsibility of the purchaser.
Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue strength, surface appearance and welding properties, the user should consult the supplier and consider the relevant special European Standard, as applicable.

This European standard specifies particular requirements applicable to wrought aluminium and aluminium alloys intended for the production of pressure equipment.

This European Standard specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm.
It applies to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process, either in the final width or slit afterwards, and to sheet obtained from such strip.
It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

This standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensil applications. This standard is applicable to: - circles made out of hot or cold-rolled circle stock, with a thickness from 0,2 mm up to and including 12 mmand with a diameter from 100 mm up to and including 1 600 mm. Note: Circles witha diameter up to 1 000 mm may be produced by blanking. - hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.

This standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.It applies to: 1) circles made out of hot or cold-rolled circle stock by: - blanking: thickness 0,2 mm up to and including 12 mm and with a diameter up to 1000 mm; - sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3500 mm. 2) hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3500 mm.

This European Standard specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3.
Temper designations are defined in Annex B, in compliance with the provisions of EN 515.

This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications. It also includes provision for ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
It does not directly apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special applications such as aerospace, can stock, finstock, etc. which are dealt with in separate European Standards.
NOTE   Most of these specific standards refer for some provisions to the present standard.

This European Standard specifies the technical conditions of inspection and delivery, the mechanical properties, and electrical conductivity of wrought aluminium sheet, strip and plate for electrotechnical applications such as bus bars and other conductors, products requiring a certain minimum electrical conductivity.

This European Standard specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3.
Temper designations are defined in Annex B, in compliance with the provisions of EN 515.

This document specifies the technical conditions of inspection and delivery, the mechanical properties, the tolerances on dimensions and form of rolled semi-finished aluminium alloy products intended for tanks for the storage and transportation of dangerous goods, in particular of gasoline and other liquid hydrocarbons.
It applies to hot or cold-rolled strip, sheet and plate with a thickness from 3,0 mm and up to and including 12,0 mm used as a wall material.
NOTE 1   Compliance with the present document does not ensure compliance with national or international regulations. The user of the document is responsible for checking that the material he orders or sells complies with all applicable regulations. Depending on the chemical and physical properties of the dangerous good to be transported or stored, it can be necessary to agree on additional properties or inspection conditions in order to comply with applying regulations.

This standard specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy sheet, strip and plate for general engineering applications.  It applies to products with a thickness over 0,20 mm up to and including 200 mm.  It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special applicatios such as aerospace , can stock, finstock, etc. which are dealt with in separate European Standards.

This European Standard gives the forms of products which are currently available for wrought aluminium and aluminium alloys, for each major field of application.
It applies to aluminium and aluminium alloys with the chemical compositions specified in EN 573-3.
NOTE   Some of the products listed in the present standard can be subject to patent or patent applications, and their listing herein does not in any way imply the granting of a licence under such patent right.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.
It uses the four-figure numerical and the alternative chemical symbol based alloy designation systems specified respectively in EN 573-1 and EN 573-2.

This European Standard specifies the chemical composition limits of wrought aluminium and aluminium alloys.
The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Association, Washington DC 20006, USA, for the corresponding alloys.
NOTE   Some of the products listed in the present standard can be subject to patent or patent applications, and their listing herein should not be construed in any way as the granting of a licence under such patent rights.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on a standardised product under reasonable and not discriminatory conditions, then this product shall be excluded from the corresponding standard.

This European standard specifies the technical conditions for inspection and delivery, mechanical properties, dimensional tolerances and other requirements for wrought aluminium and aluminium alloy sheets, strips and plates, rolled flat with a raised pattern on one side and a smooth surface on the other side. It applies to sheets, strips and plates 1,2 mm to 20 mm in thickness and up to 2500 mm in width, and to sheets and plates up to 12500 mm in length.

This part of EN 485 specifies the mechanical properties of wrought aluminium and aluminium alloy sheet, strip and plate for general engineering applications. It applies to flat rolled products. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, etc., sheets and strips or to special applications such as aerospace, can stock, finstock, etc., which are dealt with in separate EN standards.

This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 2,0 mm but thicknesses up to 3,0 mm are also available.  It applies to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process, either in the final width or slit afterwards, and to sheet obtained from such strip.   It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

This part of EN 485 specifies the mechanical properties of wrought aluminium and aluminium alloy sheets, strips and plates for general engineering applications.   It applies to flat rolled products.   It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, etc. sheets and strips or to special applications such as aerospace, can stock, finstock, etc. which are dealt with in separate EN standards.  The systems for designating these materials are described in EN 573-1 and EN 573-2. Their chemical composition limits are given in EN 573-3.  Mechanical property limits are specified for all Class A alloys, as defined in EN 573-4.  Temper designations are defined in EN 515.

This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by hot-rolling, for general engineering applications. It applies to products with a thickness from 2,5 mm up to and including 200 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated embossed, etc. sheet and strip or to special applications such as aerospace which are dealt with in separate European standards.