EN 485-3:1993
(Main)Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on shape and dimensions for hot-rolled products
Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on shape and dimensions for hot-rolled products
This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by hot-rolling, for general engineering applications. It applies to products with a thickness from 2,5 mm up to and including 200 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated embossed, etc. sheet and strip or to special applications such as aerospace which are dealt with in separate European standards.
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 3: Grenzabmaße und Formtoleranzen für warmgewalzte Erzeugnisse
Dieser Teil der EN 485-3 legt die Grenzabmasse und Formtoleranzen für warmgewalzte Bänder, Bleche und Platten aus Aluminium und Aluminiumlegierungen fest, die für allgemeine Verwendungen bestimmt sind. Er gilt nicht für Vorwalzbänder, nicht für Spezialerzeugnisse, wie z.B. geprägte oder rollgeformte Bänder und Bleche, und nicht für Erzeugnisse, die für Spezialanwendungen, wie beispielsweise Luft- und Raumfahrt eingesetzt werden. Diese werden in gesonderten Europäischen Normen abgehandelt. Die zugehörigen technischen Lieferbedungenen sind in der EN 485-1 festgelegt.
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 3: Tolérances sur forme et dimensions des produits laminés à chaud
La présente partie de la norme EN 485 spécifie les tolérances sur forme et dimensions des tôles, bandes et tôles épaisses en aluminium et alliages corroyés obtenues par laminage à chaud, pour usages généraux. Elle s'applique aux produits d'épaisseur comprise entre 2,5 mm et 200 mm inclus. Elle ne s'applique pas aux demi-produit laminés, livrés en bobine, desinté à être relaminés (ébauches) ni aux produits spéciaux tels que tôles et bandes ondulées, gravées, etc., ni aux applications spéciales telles que la construction aéronautique qui font l'objet de normes européennes particulières.
Aluminij in aluminijeve zlitine - Pločevine, trakovi in plošče - 3. del: Tolerance oblik in odstopki mer toplo valjanih izdelkov
General Information
- Status
- Withdrawn
- Publication Date
- 14-Oct-1993
- Withdrawal Date
- 18-Mar-2003
- Technical Committee
- CEN/TC 132 - Aluminium and aluminium alloys
- Drafting Committee
- CEN/TC 132/WG 7 - Sheets, strips and plates
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 19-Mar-2003
- Completion Date
- 19-Mar-2003
- Directive
- 97/23/EC - Pressure equipment
Relations
- Effective Date
- 22-Dec-2008
- Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
Element Materials Technology
Materials testing and product certification.
Inštitut za kovinske materiale in tehnologije
Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.
Sponsored listings
Frequently Asked Questions
EN 485-3:1993 is a standard published by the European Committee for Standardization (CEN). Its full title is "Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on shape and dimensions for hot-rolled products". This standard covers: This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by hot-rolling, for general engineering applications. It applies to products with a thickness from 2,5 mm up to and including 200 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated embossed, etc. sheet and strip or to special applications such as aerospace which are dealt with in separate European standards.
This part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by hot-rolling, for general engineering applications. It applies to products with a thickness from 2,5 mm up to and including 200 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated embossed, etc. sheet and strip or to special applications such as aerospace which are dealt with in separate European standards.
EN 485-3:1993 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 485-3:1993 has the following relationships with other standards: It is inter standard links to EN 485-3:2003, EN 1252-1:1998. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 485-3:1993 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 485-3:1993 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-1998
$OXPLQLMLQDOXPLQLMHYH]OLWLQH3ORþHYLQHWUDNRYLLQSORãþHGHO 7ROHUDQFHREOLN
LQRGVWRSNLPHUWRSORYDOMDQLKL]GHONRY
Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on shape
and dimensions for hot-rolled products
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 3:
Grenzabmaße und Formtoleranzen für warmgewalzte Erzeugnisse
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 3:
Tolérances sur forme et dimensions des produits laminés a chaud
Ta slovenski standard je istoveten z: EN 485-3:1993
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
-----------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...