EN IEC 60512-1:2018

SLOVENSKI STANDARD
01-februar-2018
1DGRPHãþD
SIST EN 60512-1:2002
.RQHNWRUML]DHOHNWULþQRLQHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO
6SORãQDVSHFLILNDFLMD,(&
Connectors for electrical and electronic equipment - Tests and measurements - Part 1:
Generic specification (IEC 60512-1:2018)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 1:
Allgemeines (IEC 60512-1:2018)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 1: Généralités
(IEC 60512-1:2018)
Ta slovenski standard je istoveten z: EN IEC 60512-1:2018
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60512-1

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2018
ICS 31.220.10 Supersedes EN 60512-1:2001
English Version
Connectors for electrical and electronic equipment - Tests and
measurements - Part 1: Generic specification
(IEC 60512-1:2018)
Connecteurs pour équipements électroniques et Steckverbinder für elektrische und elektronische
électroniques - Essais et mesures - Partie 1: Spécification Einrichtungen - Mess- und Prüfverfahren - Teil 1:
générique(IEC 60512-1:2018) Allgemeines(IEC 60512-1:2018)
This European Standard was approved by CENELEC on 2018-11-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60512-1:2018 E

European foreword
The text of document 48B/2667/FDIS, future edition 5 of IEC 60512-1, prepared by SC 48B "Electrical
connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical and electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-08-26
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-11-26
document have to be withdrawn
This document supersedes EN 60512-1:2001.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60512-1:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61984:2008 NOTE Harmonized as EN 61984:2009 (not modified)
ISO/IEC 17025 NOTE Harmonized as EN ISO/IEC 17025

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 2013 Environmental testing - Part 1: General and EN 60068-1 2014
guidance
IEC 60352-1 1997 Solderless connections - Part 1: Wrapped EN 60352-1 1997
connections - General requirements, test methods
and practical guidance
IEC 60352-2 2006 Solderless connections - Part 2: Crimped EN 60352-2 2006
connections - General requirements, test methods
and practical guidance
IEC 60352-3 1993 Solderless connections - Part 3: Solderless EN 60352-3 1994
accessible insulation displacement connections -
General requirements, test methods and practical
guidance
IEC 60352-4 1994 Solderless connections - Part 4: Solderless non- EN 60352-4 1994
accessible insulation displacement connections -
General requirements, test methods and practical
guidance
IEC 60352-5 2012 Solderless connections - Part 5: Press-in EN 60352-5 2012
connections - General requirements, test methods
and practical guidance
IEC 60352-6 1997 Solderless connections - Part 6: Insulation piercing EN 60352-6 1997
connections - General requirements, test methods
and practical guidance
IEC 60352-7 2002 Solderless connections - Part 7: Spring clamp EN 60352-7 2002
connections - General requirements, test methods
and practical guidance
IEC 60352-8 2011 Solderless connections - Part 8: Compression mount EN 60352-8 2011
connections - General requirements, test methods
and practical guidance
IEC 60512-1-100 -  Connectors for electronic equipment - Tests and - -
measurements - Part 1-100: General - Applicable
publications
IEC 60512-1-101 -  Connectors for electronic equipment - Tests and - -
measurements - Part 1-101: Blank detail
specification
IEC 61076-1 -  Connectors for electronic equipment - Product EN 61076-1 -
requirements - Part 1: Generic specification

IEC 60512-1 ®
Edition 5.0 2018-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment – Tests and measurements –

Part 1: Generic specification
Connecteurs pour équipements électriques et électroniques –

Essais et mesures –
Partie 1: Spécification générique

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-6075-3

– 2 – IEC 60512-1:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 6
4 Numbering of tests and measurements specification . 9
5 Preparation for test (description and instructions) . 10
5.1 Test apparatus . 10
5.1.1 Test equipment, fixture and gauge . 10
5.1.2 Calibration . 10
5.2 Preparation of specimens . 11
5.3 Wiring . 11
5.4 Mounting of specimen . 11
6 Test (description and instructions). 11
6.1 Tests and measurements . 11
6.2 Test sequences . 12
6.3 Combined tests . 12
6.4 Dimensional measurements . 12
6.5 Alternative test methods . 12
7 Requirements . 12
8 Documentation . 12
Bibliography . 14

IEC 60512-1:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60512-1 has been prepared by subcommittee 48B: Electrical
connectors, of IEC technical committee 48: Electrical connectors and mechanical structures
for electrical and electronic equipment.
This fifth edition cancels and replaces the fourth edition, published in 2001. It constitutes a
technical revision.
This edition includes the following main technical changes with respect to the previous edition:
– in Clause 3, only terms relating to the testing are define
...