M/536 - Radio equipment

Identical adoption of future IEC/IEEE 63195-1 into EN IEC/IEEE 63195-1.

Identical adoption of future IEC/IEEE 63195-2 into EN IEC/IEEE 63195-2

IEC 63404:2024 defines radiocommunication related requirements for equipment intended to integrate a radiocommunication device. It includes the initial integration and update of a the radiocommunication device, having a carrier frequency greater than 380 MHz, into new or updated host equipment with:
- The classification of integration categories;
- The EMC immunity verification using a capability profile approach;
- The verification of the unwanted emission level of the radio transceiver.

2021-09-24: This prAA includes common mods to EN 60730-1:2016/A2 (PR=67139)

IEC 61851-24:2023, together with IEC 61851-23, applies to digital communication between a DC EV supply equipment and an electric road vehicle (EV) for control of conductive DC power transfer, with a rated supply voltage up to 1 000 V AC or up to 1 500 V DC and a rated output voltage up to 1 500 V DC.
This document also applies to digital communication between the DC EV charging/discharging station and the EV for system A, as specified in Annex A.
The EV charging mode is mode 4, according to IEC 61851-23.
Annex A, Annex B, and Annex C give descriptions of digital communications for control of DC charging specific to DC EV charging systems A, B and C as defined in IEC 61851-23.
This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Annex A and Annex B have been updated in line with IEC 61851-23:2023 and relevant standards.

The contents of the Interpretation sheet 1 (2025-04), applying to the English version only, have been included in this copy.

IEC 63404:2024 defines radiocommunication related requirements for equipment intended to integrate a radiocommunication device. It includes the initial integration and update of a the radiocommunication device, having a carrier frequency greater than 380 MHz, into new or updated host equipment with: - The classification of integration categories; - The EMC immunity verification using a capability profile approach; - The verification of the unwanted emission level of the radio transceiver.

NEW!IEC 60335-2-102:2017 is available as IEC 60335-2-102:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60335-2-102:2017 deals with the safety of gas, oil and solid-fuel burning appliances having electrical connections, for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard covers the electrical safety and some other safety aspects of these appliances. All safety aspects are covered when the appliance also complies with the relevant standard for the fuel-burning appliance. If the appliance incorporates electric heating sources, safety aspects concerning these electric sources are covered when the appliance also complies with  the relevant part 2 of IEC 60335. Examples of appliances within the scope of this standard are
– central heating boilers;
– commercial catering equipment;
– cooking appliances;
– laundry and cleaning appliances;
– room heaters;
– warm air heaters;
– water heaters.
Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. This standard deals with the reasonably foreseeable hazards presented by appliances that are encountered by all persons. However, in general, it does not take into account  
– persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
Attention is drawn to the fact that
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary;
This standard does not apply to
– appliances intended exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). This second edition cancels and replaces the first edition published in 2004 including its Amendment 1 (2008) and its Amendment 2 (2012). This edition constitutes constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a spillage test is introduced for appliances that have a flat surface on which a cup may be placed (15.101); terms and definitions were renumbered and some notes have been converted to normative text or deleted (19.11.2, 22.103). This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2-102 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of IEC 60335-1:2010, its Amendment 1:2013 and its Amendment 2:2016. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of

2021-09-24: This prAA includes common mods to EN 60730-1:2016/A2 (PR=67139)

IEC 60703-1:2022 applies to automatic electrical controls for use in, on, or in association with equipment for household appliance and similar use. This document applies to - the inherent safety of automatic electrical controls, and - functional safety of automatic electrical controls and safety related systems, - controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system, - the operating values, operating times, and operating sequences where such are associated with equipment safety. This document specifies the requirements for construction, operation and testing of automatic electrical controls used in, on, or in association with an equipment.

2022-02-21: This prAA covers common mods to prEN IEC 62368-1 - PR=74334

IEC 62368-1:2023 is available as IEC 62368-1:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 62368-1:2023 is a product safety standard that classifies energy sources, prescribes safeguards against those energy sources, and provides guidance on the application of, and requirements for, those safeguards. The prescribed safeguards are intended to reduce the likelihood of pain, injury and, in the case of fire, property damage. The objective of the introduction is to help designers to understand the underlying principles of safety in order to design safe equipment. These principles are informative and not an alternative to the detailed requirements of this document.

IEC 62368-1:2023 is available as IEC 62368-1:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62368-1:2023 is a product safety standard that classifies energy sources, prescribes safeguards against those energy sources, and provides guidance on the application of, and requirements for, those safeguards. The prescribed safeguards are intended to reduce the likelihood of pain, injury and, in the case of fire, property damage. The objective of the introduction is to help designers to understand the underlying principles of safety in order to design safe equipment. These principles are informative and not an alternative to the detailed requirements of this document.

2022-02-21: This prAA covers common mods to prEN IEC 62368-1 - PR=74334

The contents of the Interpretation sheet 1 (2025-04), applying to the English version only, have been included in this copy.

This European Standard deals with the safety of electrical appliances for household environment and commercial purposes, their rated voltage being not more than 250 V for single-phase and 480 V for others.

This European Standard deals with the safety of electrical appliances for household environment and commercial purposes, their rated voltage being not more than 250 V for single-phase and 480 V for others.

NEW!IEC 60335-2-86:2018 is available as IEC 60335-2-86:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60335-2-86:2018 deals with the safety of electric fishing machines by means of which water may be electrified for the purpose of catching fish or for providing barriers to all animals living in water. The rated voltage of electric fishing machines is not more than 250 V for single phase machines and 480 V for other machines, except that the rated voltage of electric fishing machines for permanent connection to fixed wiring is not more than 1 000 V. Electric fishing machines are appliances for scientific and commercial use. Additional requirements for boat mounted electric fishing machines are given in Annex AA. This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2005) and its Amendment 2 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- aligns the text with IEC 60335-1, Ed 5, and its Amendments 1 and 2;
- some notes have been converted to normative text (22.102, 22.113, 26.106);
- requirements for battery-operated electric fishing machines have been moved to Annex S.

This European Standard deals with the safety of electrical appliances for household environment and commercial purposes, their rated voltage being not more than 250 V for single-phase and 480 V for others.

This European Standard deals with the safety of electrical appliances for household environment and commercial purposes, their rated voltage being not more than 250 V for single-phase and 480 V for others.

NEW!IEC 60335-2-86:2018 is available as IEC 60335-2-86:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-86:2018 deals with the safety of electric fishing machines by means of which water may be electrified for the purpose of catching fish or for providing barriers to all animals living in water. The rated voltage of electric fishing machines is not more than 250 V for single phase machines and 480 V for other machines, except that the rated voltage of electric fishing machines for permanent connection to fixed wiring is not more than 1 000 V. Electric fishing machines are appliances for scientific and commercial use. Additional requirements for boat mounted electric fishing machines are given in Annex AA. This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2005) and its Amendment 2 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - aligns the text with IEC 60335-1, Ed 5, and its Amendments 1 and 2; - some notes have been converted to normative text (22.102, 22.113, 26.106); - requirements for battery-operated electric fishing machines have been moved to Annex S.

This product standard applies to wireless communication devices used in close proximity to the human ear (e.g. mobile phones, wireless headsets). The applicable frequency range is from 300 MHz to 6 GHz.
The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields.
For devices used next to the body or in front of the face the applicable product standard is EN 50566:2017.
For low power devices the applicable product standard is EN 50663:2017.

This product standard applies to wireless communication devices used at distances up to and including 200 mm from the human body, i.e. when held in the hand or in front of the face, mounted on the body, combined with other transmitting or non-transmitting devices or accessories (e.g. belt-clip, camera or Bluetooth add-on), or integrated into garments. The applicable frequency range is from 30 MHz to 6 GHz.
The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields.
For devices used next to the ear the applicable product standard is EN 50360:2017 [1].
For low power devices the applicable product standard is EN 50663:2017 [2].

This product standard applies to wireless communication devices used in close proximity to the human ear (e.g. mobile phones, wireless headsets). The applicable frequency range is from 300 MHz to 6 GHz. The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields. For devices used next to the body or in front of the face the applicable product standard is EN 50566:2017. For low power devices the applicable product standard is EN 50663:2017.

This document specifies safety requirements for radio-integrated lighting equipment.
NOTE 1 Examples for lighting equipment are light sources, lamps, luminaires and controlgear for light sources.
NOTE 2 With the radio equipment integrated into the lighting equipment, the lighting equipment itself becomes radio
equipment which is subject to the provisions of the RED.

This document specifies safety requirements for radio-integrated lighting equipment. NOTE 1 Examples for lighting equipment are light sources, lamps, luminaires and controlgear for light sources. NOTE 2 With the radio equipment integrated into the lighting equipment, the lighting equipment itself becomes radio equipment which is subject to the provisions of the RED.

This clause of Part 1 is completely replaced by the following:
This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons.
This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF.
Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices.
This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls).
The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed:
- intentionally by a person via an actuating member, a key, a card, etc., via a sensing
surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal;
- by physical means, for example, light, temperature, humidity, time, wind velocity, presence
of people;
- by any other influence.
This document also applies to electronic control devices which include integrated radio receivers and transmitters.
This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices.
Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670.
This document is not intended to cover devices falling within the scope of IEC 60730 (all parts).
Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of −5 °C.
NOTE 1 For lower temperatures, see Annex E.
Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices.
In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required.
This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1.
Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA.
Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC.
Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE.
NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.

To give requirements and tests for electronic control devices, a general term to cover electronic switches, HBES/BACS switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC.
This Part of IEC 60669 also applies to electronic control devices which include integrated radio receivers and transmitters.

IEC 60335-2-71:2018 deals with the safety of all kinds of electrical heating appliances used for livestock rearing and breeding, such as: heat-radiating appliances, electrical sitting-hens, incubators, chicken breeding units and heating plates for animals, the rated voltage of the appliances being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard applies to heating appliances used for livestock rearing and breeding that include an electrical motor. This standard does not apply to: - appliances designed exclusively for industrial purposes; - appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); - heating units embedded in the floor; - flexible sheet heating elements for room heating (IEC 60335-2-96); - room heaters (IEC 60335-2-30). This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2007) and its Amendment 2 (2012). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - two paragraphs are deleted (Introduction); - normative references updated (Clause 2); - colour required for symbols (7.6); - some notes converted to normative text (19.2, 21.101, 22.104).

NEXT ACTION: PUBLICATION EXPECTED BY 2020-04

Identical adoption of future IEC/IEEE 63195-1 into EN IEC/IEEE 63195-1.

Identical adoption of future IEC/IEEE 63195-2 into EN IEC/IEEE 63195-2

2021-10-25: temporary removed link  GPSD until feedback from EC
2019-10-01: BT decision D163/015.: decouple from OJEU citation process
2019-09-02 NEXT STEP: BT consultation on 1 Oct. 2019
2019-09-02: doc for BT meeting 1 Oct asking to decouple + no HAS assessment needed
2019-08-06 text for FV submitted, asking to decouple from OJEU
2019-05-24 TC 108X+CCMC+EC+HAS Cons comments resolution meeting
2019-03-15 - GEM - issues with ENQ text for PR= 67625 - way forward proposed to TC (incl. WS with EC)
2019-03-01 GEM:  HAS assessment challenged
2018-11-09 - GEM - project is extremely important and urgent  for industry. The standard needs to be 'harmonized', it is imperative to get to a positive assessment prior to launching ENQ. --> See GEM before starting any action
2018-07-09 - GEM - Common modifications to prEN 62368-1 (PR = 67625)..
Synchronyze enquiry with enquiry for  adoption of  IEC 62368-1 Ed.3 (PR=67625).
HAS Consultant assessment of main + amdt required - assessment to b

2020-12-01: no xml because common mod
2019-10-29: D164/C050: Amendment to add Annex ZZ to EN 55032:2015 & enable citation in OJEU
2021: CLC legacy converted by DCLab NISOSTS

NEW!IEC 60335-2-102:2017 is available as IEC 60335-2-102:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-102:2017 deals with the safety of gas, oil and solid-fuel burning appliances having electrical connections, for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard covers the electrical safety and some other safety aspects of these appliances. All safety aspects are covered when the appliance also complies with the relevant standard for the fuel-burning appliance. If the appliance incorporates electric heating sources, safety aspects concerning these electric sources are covered when the appliance also complies with the relevant part 2 of IEC 60335. Examples of appliances within the scope of this standard are – central heating boilers; – commercial catering equipment; – cooking appliances; – laundry and cleaning appliances; – room heaters; – warm air heaters; – water heaters. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. This standard deals with the reasonably foreseeable hazards presented by appliances that are encountered by all persons. However, in general, it does not take into account – persons (including children) whose • physical, sensory or mental capabilities; or • lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; – children playing with the appliance. Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). This second edition cancels and replaces the first edition published in 2004 including its Amendment 1 (2008) and its Amendment 2 (2012). This edition constitutes constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a spillage test is introduced for appliances that have a flat surface on which a cup may be placed (15.101); terms and definitions were renumbered and some notes have been converted to normative text or deleted (19.11.2, 22.103). This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2-102 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of IEC 60335-1:2010, its Amendment 1:2013 and its Amendment 2:2016. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of

This part of IEC 60974 specifies safety and construction requirements for TORCHES used for arc welding and allied processes. This document is applicable to MANUAL, MECHANICALLY GUIDED, AIR-COOLED, LIQUID-COOLED, MOTORIZED, SPOOL-ON and FUME EXTRACTION TORCHES. In this document, a TORCH consists of the TORCH BODY, the CABLE-HOSE ASSEMBLY and other components. This document is also applicable to a CABLE-HOSE ASSEMBLY connected between a power source and ancillary equipment. This document is not applicable to electrode holders for manual metal arc welding or air-arc cutting/gouging. NOTE 1 Typical allied processes are electric arc cutting and arc spraying. NOTE 2 Other components are listed in Table A.1. NOTE 3 In this document, all procedures and requirements are the same for "TORCHES" and "GUNS". For convenience, the term "TORCH" is used in the following text.

2018-11-10 AAP: Waiting for assessment from LVD consultant.

NEW!IEC 61000-3-11:2017 is available as IEC 61000-3-11:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61000-3-11:2017 is concerned with the emission of voltage changes, voltage fluctuations and flicker produced by equipment and impressed on the public low-voltage supply system. It specifies the limits of voltage changes produced by equipment tested under specified conditions. This edition includes the following significant technical changes with respect to the previous edition: a) addition of a new Annex A which explains the limitations and effectiveness of IEC 61000‑3-11 regarding the connection of multiple items of similar equipment at the same location in the supply network.

2022-04-07: This EN has no DOW.
NEXT ACTION: TC ACTION by 2022-06-01
2021-12-16: DOW removed from A1 further to  D170/C058. Mother EN has no DOW (justification in foreword)
2021-09-24: prAA including common mods to this A2 will be presented soon to BT
NEXT ACTION: TC ACTION by 2021-12-01
2020-08-19: NEXT ACTION BY TC: to deliver Annexes for FV assessment.

IEC 61000-6-4:2018 is also available as IEC 61000-6-4:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
\r\n
\r\nIEC 61000-6-4:2018 for emission requirements applies to electrical and electronic equipment intended for use within the environment existing at industrial (see 3.1.12) locations. This document does not apply to equipment that fall within the scope of IEC 61000-6-3. The environments encompassed by this document cover both indoor and outdoor locations. Emission requirements in the frequency range 9 kHz to 400 GHz are covered in this document and have been selected to provide an adequate level of protection of radio reception in the defined electromagnetic environment. No measurement needs to be performed at frequencies where no requirement is specified. These requirements are considered essential to provide an adequate level of protection to radio services. Not all disturbance phenomena have been included for testing purposes but only those considered relevant for the equipment intended to operate within the environments included within this document. Requirements are specified for each port considered. This generic EMC emission standard is to be used where no applicable product or product-family EMC emission standard is available. This third edition cancels and replaces the second edition published in 2006 and Amendment 1:2010 This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
\r\na) possible future requirements on DC ports;
\r\nb) possible future radiated polarity specific emission limits within a FAR;
\r\nc) the definition of which average detector is used for emission measurements at frequencies above 1GHz and that results using a peak detector are acceptable for all measurements;
\r\nd) the definition of different EUT test arrangements.
\r\nKeywords: emission standard for industrial environments