M/132 - CPD: Circultation fixtures, ..

This European Standard covers the design of devices that are provided in structures, with the aim of modifying their response to the seismic action. It specifies functional requirements and general design rules for the seismic situation, material characteristics, manufacturing and testing requirements, as well as evaluation of conformity, installation and maintenance requirements. This European Standard covers the types of devices and combinations thereof as defined in 3.4.
NOTE   Additional information concerning the scope of this European Standard is given in Annex A.

This European Standard covers the design of devices that are provided in structures, with the aim of modifying their response to the seismic action. It specifies functional requirements and general design rules of the devices for the seismic and non-seismic design situations, material characteristics, manufacturing and testing requirements, as well as assessment and verification of constancy of performance, installation and maintenance requirements. This European Standard covers the types of devices and combinations thereof as defined in 3.4.
NOTE   Additional information concerning the scope of this European Standard is given in Annex A.

This document applies to calcium sulphate binders and composite binders made of calcium sulphate used for the manufacture of floor screeds for interior use in buildings. It also includes requirements for factory made mixtures made of calcium sulphate used for the manufacture of floor screeds which are given in EN 13813. This document does not cover the application of floor screeds. Floor screeds made with products covered by this document may contribute to thermal and sound insulation and fire protection of the floor.

This document applies to calcium sulphate binders and composite binders made of calcium sulphate used for the manufacture of floor screeds for interior use in buildings. It also includes requirements for factory made mixtures made of calcium sulphate used for the manufacture of floor screeds which are given in EN 13813. This document does not cover the application of floor screeds. Floor screeds made with products covered by this document may contribute to thermal and sound insulation and fire protection of the floor.

This European Standard applies to caustic magnesia and magnesium chloride used for the manufacture of magne-site screed material and magnesite floor screeds as specified in EN 13813 and describes test methods by means of which the fulfilment of the requirements in EN 14016-1 can be checked.

This European Standard specifies requirements for caustic magnesia and magnesium chloride, which will be used for magnesite screed material and magnesite screeds as specified in EN 13813.

This European Standard applies to caustic magnesia and magnesium chloride used for the manufacture of magne-site screed material and magnesite floor screeds as specified in EN 13813 and describes test methods by means of which the fulfilment of the requirements in EN 14016-1 can be checked.

This European Standard specifies requirements for caustic magnesia and magnesium chloride, which will be used for magnesite screed material and magnesite screeds as specified in EN 13813.

This European standard specifies a method for determining the flexural and compressive strength of moulded mortar specimens made from cementitious screed-, calcium sulfate screed-, magnesite screed- and synthetic resin material.

This European Standard specifies a method for determining the bond strength between a screed and a standard substrate and specifies a method for determining the tensile strength at the surface of specimens made from cementitious screed-, calcium sulfate, screed-, magnesia screed- and synthetic resin screed material. The method is also suitable for floor screeds for determining the tensile strength at the surface of the floor screed or for determining the bond strength between a bonded floor screed and a base.

This European standard specifies a method for determining the surface hardness of moulded mortar specimens made from magnesite screed material or from cementitious screed-, calcium sulfate screed-, and synthetic resin screed material with fine aggregates (

Migrated from Progress Sheet (TC Comment) (2000-07-10): WIs 006-015 are the result of the splitting of WI 002 (TC Res 25/1998)(CC980806)

It defines for fresh screed material the performance related to working time, consistency, pH value and for hardened screed material, compressive strength, flexural strength, wear resistance, surface hardness, resistance to uindentation, resistance to rolling wheel, shrinkage and swelling, modulus of elasticity and bond strength. It provides for the evaluation of conformity of the product to this draft European standard. The marking requirements for products covered by this draft European standard are included. This standard covers screed materials as defined in prEN 13318.

This European Standard specifies a method for determining the wear resistance of test specimens made from cementitious- or synthetic resin screed material or optionally for other screed materials. The method is also suitable for floor screeds.

This European Standard specifies a method for determining the bond strength between a screed and a standard substrate and specifies a method for determining the tensile strength at the surface of specimens made from cementitious screed-, calcium sulfate, screed-, magnesia screed- and synthetic resin screed material. The method is also suitable for floor screeds for determining the tensile strength at the surface of the floor screed or for determining the bond strength between a bonded floor screed and a base.

This European standard specifies a method for determining the flexural and compressive strength of moulded mortar specimens made from cementitious screed-, calcium sulfate screed-, magnesite screed- and synthetic resin material.

This European standard specifies a method for determining the surface hardness of moulded mortar specimens made from magnesite screed material or from cementitious screed-, calcium sulfate screed-, and synthetic resin screed material with fine aggregates (

It defines for fresh screed material the performance related to working time, consistency, pH value and for hardened screed material, compressive strength, flexural strength, wear resistance, surface hardness, resistance to uindentation, resistance to rolling wheel, shrinkage and swelling, modulus of elasticity and bond strength. It provides for the evaluation of conformity of the product to this draft European standard. The marking requirements for products covered by this draft European standard are included. This standard covers screed materials as defined in prEN 13318.

This document applies to binders made of calcium sulphate used for the manufacture of floor screeds for interior use in buildings. It also includes requirements for factory made mixtures made of calcium sulphate used for the manufacture of floor screeds which are given in EN 13813. This document does not cover the application of floor screeds. Floor screeds made with products covered by this document can contribute to thermal and sound insulation and fire protection of the floor.

This standard specifies the initial performance requirements and laboratory test methods for solar powered, hardwired and communicating active road studs intended for use as permanent and temporary road marking materials.

This European Standard specifies requirements for the following types of screed material as defined in EN 13318:
-   Cementitious;
-   Calcium sulphate;
-   Magnesite;
-   Mastic asphalt;
-   Synthehic resin.
All types of screed material may be used for internal applications.
Cementitious screed material may be used for both internal and external applications.
This European Standard specifies the performance for fresh and hardened screed materials.
The floor screed materials could be monolayer or multilayer.
This European Standard specifies the assessment and verification of the constancy of performance and the classification and designation of screed materials.
This European Standard does not provide criteria or recommendations for the design and installation of screed materials.

This European Standard specifies the requirements for laboratory tests (production control) and qualification procedures for the following drop on materials used in road markings.
These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface.
The requirements taken into consideration in this standard are :
- glass beads : granulometry, refractive index of the glass, chemical resistance, quality, surface treatments ;
- antiskid aggregates : granulometry, chemical characteristics, friability, colour ;
- mixtures of glass beads and antiskid aggregates; and the requirements for both components.

This standard specifies the initial performance requirements and laboratory test methods for solar powered, hardwired and communicating active road studs intended for use as permanent and temporary road marking materials.

This document applies to binders made of calcium sulphate used for the manufacture of floor screeds for interior use in buildings. This document does not cover the application of floor screeds. Floor screeds made with products covered by this document can contribute to thermal and sound insulation and fire protection of the floor.
This document specifies binders where the principal active constituent is calcium sulphate.
Factory made mixtures are covered by EN 13813 and are therefore not part of this document.

This document specifies requirements for the following types of screed material as defined in EN 13318:
-   cementitious;
-   calcium sulfate;
-   magnesite;
-   mastic asphalt;
-   synthetic resin.
All types of screed material can be used for internal applications. However, cementitious screed materials can also be used for internal and external applications.
This document specifies the properties for fresh and hardened screed materials.
The floor screed materials could be installed as monolayer or multilayer products.
This document specifies designation of the screed materials as well as designation and classification of their characteristics. Furthermore, it also specifies the assessment and verification of constancy of performance, marking and labelling of the screed materials.
This document does not provide criteria or recommendations for the design and installation of screed materials.

This European Standard specifies the requirements for laboratory tests (production control) and qualification procedures for the following drop on materials used in road markings.
These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface.
The requirements taken into consideration in this standard are :
- glass beads : granulometry, refractive index of the glass, chemical resistance, quality, surface treatments ;
- antiskid aggregates : granulometry, chemical characteristics, friability, colour ;
- mixtures of glass beads and antiskid aggregates; and the requirements for both components.

This European standard covers the design of devices that are provided in structures with the aim of modifying their response to the seismic action. It specifies functional requirements and general design rules in the seismic situation, material characteristics, manufacturing and testing requirements, as well as acceptance, installation and maintenance criteria.
This European standard covers the types of devices listed in table 1 (see 3.4).
NOTE   Additional information concerning the scope of this European standard is given in Annex A.

This European Standard covers the design of devices that are provided in structures, with the aim of modifying their response to the seismic action. It specifies functional requirements and general design rules for the seismic situation, material characteristics, manufacturing and testing requirements, as well as evaluation of conformity, installation and maintenance requirements. This European Standard covers the types of devices and combinations thereof as defined in 3.4.
NOTE   Additional information concerning the scope of this European Standard is given in Annex A.

This European Standard specifies a method for determining the wear resistance of moulded specimens made from cementitious screed material, primarily for hard aggregate wearing screed materials or optionally for other screed materials. The method is also suitable for specimens cut from floor screed. This method is unsuitable for synthetic resin screed materials.

This European Standard specifies a method for determining the wear resistance of moulded specimens made from cementitious screed material, primarily for hard aggregate wearing screed materials or optionally for other screed materials. The method is also suitable for specimens cut from floor screed. This method is unsuitable for synthetic resin screed materials.

This European Standard specifies the equipment and procedures for determining the water vapour transmission rate, water vapour permeance and water vapour permeability of test specimens in the steady state under different sets of specified test conditions. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials (see note 1) and for products which may contain integral skins or facings of different material(s).

This European Standard specifies the equipment and procedures for determining the water vapour transmission rate, water vapour permeance and water vapour permeability of test specimens in the steady state under different sets of specified test conditions. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials (see note 1) and for products which may contain integral skins or facings of different material(s).

TC - Modification to 3.1

This European Standard describes a test method for measuring the indentation of mastic asphalt when it is penetrated at a given temperature, load and for a fixed time period by a standardised cylindrical indentor pin with a circular flat-ended base. This European Standard applies to mastic asphalt with aggregates of maximum nominal size less or equal to 16 mm.

The indentation test serves to determine the depth of indentation, and thus to test the behaviour of mastic asphalt, rolled and other such asphalts, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. Mastic asphalt as described in prEN ((WI 00227009)-6) for road construction, in prEN ((CEN/TC 303WICCCC)-2) for floor screeds and in prEN (WI 31407) for waterproofing in building and engineering constructions can be tested following the test method prescribed hereafter. The maximum nominal size of the aggregates in the mix is up to and including 16 mm.

TC - Modification to 3.1

The indentation test serves to determine the depth of indentation, and thus to test the behaviour of mastic asphalt, rolled and other such asphalts, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. Mastic asphalt as described in prEN ((WI 00227009)-6) for road construction, in prEN ((CEN/TC 303WICCCC)-2) for floor screeds and in prEN (WI 31407) for waterproofing in building and engineering constructions can be tested following the test method prescribed hereafter. The maximum nominal size of the aggregates in the mix is up to and including 16 mm.

This European Standard describes a test method for measuring the indentation of mastic asphalt when it is penetrated at a given temperature, load and for a fixed time period by a standardised cylindrical indentor pin with a circular flat-ended base. This European Standard applies to mastic asphalt with aggregates of maximum nominal size less or equal to 16 mm.

This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface. The requirements taken into consideration in this standard are: - glass beads: granulometry, refractive index of the glass, chemical resistance, quality, surface treatments; - antiskid aggregates: granulometry, chemical characteristics, friability, colours.

This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface. The requirements taken into consideration in this standard are: - glass beads: granulometry, refractive index of the glass, chemical resistance, quality, surface treatments; - antiskid aggregates: granulometry, chemical characteristics, friability, colours.

This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, coldplastics and any other marking product applied in a liquid state, immediately after application to the road surface.

This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, coldplastics and any other marking product applied in a liquid state, immediately after application to the road surface.