Cable management systems - Cable ties for electrical installations

IEC 62275:2018 specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations. This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) consideration of adhesive fixing devices, b) revised and updated normative references, c) modified definitions for metallic and composite cable ties, d) new definitions, e) improvement of test procedures, f) new figures for typical arrangement of test assembly for fixing devices and for integral fixing devices.

Kabelführungssysteme - Kabelbinder für elektrische Installationen

Systèmes de câblage - Colliers pour installations électriques

L'IEC 62275:2018 spécifie les exigences pour les colliers métalliques, non métalliques et composites ainsi que pour leurs accessoires de fixation associés, utilisés pour l'aménagement et le soutien des systèmes de câblage dans les installations électriques. Cette troisième édition annule et remplace la deuxième édition parue en 2013. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) la prise en compte des accessoires de fixation adhésifs, b) des révisions et mises à jour des références normatives, c) la modification des définitions relatives aux colliers métalliques et composites, d) de nouvelles définitions, e) l'amélioration des procédures d'essai, f) de nouvelles figures avec des configurations types de l'assemblage d'essai pour les accessoires de fixation et les accessoires de fixation intégrés.

Sistemi za urejanje pokabljenja - Kabelske vezice za električne inštalacije (IEC 62275:2018)

Ta standard podaja zahteve za kovinske in nekovinske kabelske vezice ter za vezice iz kompozitnih materialov in povezana pritrdila, ki se uporabljajo za urejanje in podporo ožičenja pri električnih inštalacijah. Kabelske vezice in povezana pritrdila so lahko primerna za drugo uporabo, pri čemer je treba za takšno uporabo upoštevati dodatne zahteve. Ta dokument ne vsebuje zahtev za oceno morebitnih električnih izolativnih lastnosti kabelske vezice ali mehanske zaščite kablov, ki jo zagotavlja kabelska vezica. Ta dokument vsebuje zahteve za mehanske vmesnike prilepljenega pritrdila na trdno površino. Ne obravnava mehanskega obnašanja trdne površine kot take. Ta dokument ne obravnava mehanskega vmesnika za pritrdilo, na primer pritrdilnega vijaka, razen lepila za trdno površino.

General Information

Status
Published
Publication Date
28-Nov-2019
Withdrawal Date
28-Nov-2022
Current Stage
6060 - Document made available - Publishing
Start Date
29-Nov-2019
Completion Date
29-Nov-2019

Relations

Buy Standard

Standard
EN IEC 62275:2020
English language
45 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2020
Nadomešča:
SIST EN 62275:2015
Sistemi za urejanje pokabljenja - Kabelske vezice za električne inštalacije (IEC
62275:2018)
Cable management systems - Cable ties for electrical installations (IEC 62275:2018)
Kabelführungssysteme - Kabelbinder für elektrische Installationen (IEC 62275:2018)
Systèmes de câblage - Colliers pour installations électriques (IEC 62275:2018)
Ta slovenski standard je istoveten z: EN IEC 62275:2019
ICS:
29.120.99 Druga električna dodatna Other electrical accessories
oprema
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62275

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 29.120.10; 29.120.99 Supersedes EN 62275:2015 and all of its amendments
and corrigenda (if any)
English Version
Cable management systems - Cable ties for electrical
installations
(IEC 62275:2018)
Systèmes de câblage - Colliers pour installations Kabelführungssysteme - Kabelbinder für elektrische
électriques Installationen
(IEC 62275:2018) (IEC 62275:2018)
This European Standard was approved by CENELEC on 2018-09-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62275:2019 E
European foreword
The text of document 23A/851A/FDIS, future edition 3 of IEC 62275, prepared by SC 23A "Cable
management systems" of IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62275:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-05-29
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-11-29
document have to be withdrawn
This document supersedes EN 62275:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 62275:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 62275:2013 NOTE Harmonized as EN 62275:2015

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-6 2007 Environmental testing - Part 2-6: Tests - EN 60068-2-6 2008
Test Fc: Vibration (sinusoidal)
IEC 60216-4-1 2006 Electrical insulating materials - Thermal EN 60216-4-1 2006
endurance properties - Part 4-1: Ageing
ovens - Single-chamber ovens
IEC 60695-11-5 2016 Fire hazard testing - Part 11-5: Test flames EN 60695-11-5 2017
- Needle-flame test method - Apparatus,
confirmatory test arrangement and
guidance
ISO 4892-2 2013 Plastics - Methods of exposure to EN ISO 4892-2 2013
laboratory light sources - Part 2: Xenon-arc
lamps
ISO 9227 2017 Corrosion tests in artificial atmospheres - EN ISO 9227 2017
Salt spray tests
Annex ZZ
(informative)
Relationship between this European Standard and the safety objectives of
Directive 2014/35/EU [2014 OJ L96] aimed to be covered
This European Standard has been prepared under a Commission’s standardization request relating
to harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary
means of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of
the Council of 26 February 2014 on the harmonization of the laws of the Member States relating to
the making available on the market of electrical equipment designed for use within certain voltage
limits [2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits
of the scope of this standard, a presumption of conformity with the corresponding safety objectives
of that Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard
and Annex I of Directive 2014/35/EU [2014 OJ L96]
Safety objectives of Clause(s) / sub-clause(s) Remarks / Notes
Directive 2014/35/EU of this EN
(1)(a) Clause 7
(1)(b) Clauses 5 and 7
(1)(c) Clauses 1, 2, 3, 4 and 6
See also 2c), 3a), 3b) and 3c)
below
(2)(a) Not applicable.
Cable ties do not carry any
current, so there is no danger by
direct contact.
Cable ties are not in contact
with live parts, so there is no
danger by indirect contact
(2)(b) Not applicable
Cable ties do not carry any
current and they cannot produce
heat, arcs or radiation.
(2)(c) Clauses 8, 9 and 10 Emissions, production and/or
use of hazardous substances
not covered in this standard (but
covered in other
regulations/standards, e.g.
RoHS)
(2)(d) Not applicable.
Cable ties do not carry any
current, and therefore insulation
is not required
(3)(a) Clause 9
(3)(b) Clauses 9, 10 and 11
(3)(c) Clause 11.1
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of
this standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope
of this standard.
IEC 62275 ®
Edition 3.0 2018-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Cable management systems – Cable ties for electrical installations

Systèmes de câblage – Colliers pour installations électriques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.10; 29.120.99 ISBN 978-2-8322-5924-5

– 2 – IEC 62275:2018 © IEC 2018
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 8
5 General notes on tests . 8
6 Classification . 13
6.1 According to material . 13
6.1.1 Metallic component . 13
6.1.2 Non-metallic component . 13
6.1.3 Composite component . 13
6.2 According to loop tensile strength for cable ties and mechanical strength for
fixing devices . 13
6.2.1 Loop tensile strength for cable ties . 13
6.2.2 Type 1 – Retains at least 50 % of declared loop tensile strength for
cable ties and mechanical strength for fixing devices after test
conditions . 13
6.2.3 Type 2 – Retains 100 % declared loop tensile strength for cable ties
and mechanical strength for fixing devices after test conditions . 13
6.2.4 According to loop tensile strength and mechanical strength of integral
assemblies . 13
6.3 According to temperature . 14
6.3.1 According to maximum operating temperature for application given in
Table 4 . 14
6.3.2 According to minimum operating temperature for application given in
Table 5 . 14
6.3.3 According to minimum temperature during installation as declared by
the manufacturer . 14
6.4 According to contribution to fire for non-metallic and composite cable ties
and integral assemblies only . 14
6.4.1 Flame propagating . 14
6.4.2 Non-flame propagating . 14
6.5 According to environmental influences . 15
6.5.1 According to resistance to ultraviolet light for non-metallic and
composite components . 15
6.5.2 According to resistance to corrosion for metallic and composite
components . 15
7 Marking and documentation . 15
8 Construction . 17
9 Mechanical properties. 18
9.1 Requirements . 18
9.2 Installation test . 18
9.3 Minimum installation temperature test for cable ties . 18
9.4 Minimum operating temperature test for cable ties . 19
9.5 Loop tensile strength test for cable ties classified according to 6.2.2 . 21
9.5.1 As-received condition . 21
9.5.2 After heat ageing . 21
9.5.3 After temperature cycling .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.