EN 13236:2010/FprA1
(Amendment)Safety requirements for superabrasive products
Safety requirements for superabrasive products
This European Standard is applicable to the following superabrasive products: precision superabrasive grinding and cutting-off wheels, non-precision cutting-off wheels, diamond wires, mounted points and other superabrasive products for non-precision grinding. It also applies to reconditioned superabrasive cutting-off wheels.
This European Standard specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the superabrasive products.
This European Standard contains also procedures and tests for verification of the compliance with the requirements as well as safety information for use which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4.
This European Standard does not apply to bonded abrasive products, coated abrasive products, rotating dressing tools, truers nor any non-rotating superabrasive products.
Sicherheitsanforderungen für Schleifwerkzeuge mit Diamant oder Bornitrid
Prescriptions de sécurité pour les produits superabrasifs
Varnostne zahteve za superabrazive - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2015
Varnostne zahteve za superabrazive
Safety requirements for superabrasive products
Sicherheitsanforderungen für Schleifwerkzeuge mit Diamant oder Bornitrid
Prescriptions de sécurité pour les produits superabrasifs
Ta slovenski standard je istoveten z: EN 13236:2010/FprA1
ICS:
25.100.70 Brusiva Abrasives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 13236:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
July 2015
ICS 25.100.70
English Version
Safety requirements for superabrasive products
Prescriptions de sécurité pour les produits superabrasifs Sicherheitsanforderungen für Schleifwerkzeuge mit
Diamant oder Bornitrid
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 143.
This draft amendment A1, if approved, will modify the European Standard EN 13236:2010. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13236:2010/FprA1:2015 E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Modification to Clause 1, Scope .4
2 Addition of Subclause 5.3.7, Tensioning of non-precision cutting-off wheels .4
3 Addition of Subclause 5.3.8, Limitation of sides abrasives and/or superabrasives coating .4
4 Addition of Subclause 6.5, Verification of tensioning of non-precision cutting-off wheels .4
---------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.