EN 12413:2007/FprA1
(Amendment)Safety requirements for bonded abrasive products
Safety requirements for bonded abrasive products
Amendment:
During revision of EN 12413:1999 an editorial simplification of the table with the scope of inspection (EN 12413:1999, Table 14) had been decided (see meeting report, document CEN/TC 143/WG 2 N 132). However this simplification led to a tightening of the scope of inspection for "all other abrasive products" in EN 12413:2007, Table 7 which was not covered by the compilation of comments table (document CEN/TC 143/WG 2 N 133) and no technical reason can be seen for this tightening of requirements.
Scope of EN 12413:2007:
This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products.
This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4 of this standard.
This standard does not apply to superabrasives and coated abrasive products.
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Exigences de sécurité pour les produits abrasifs agglomérés
Varnostne zahteve za vezana brusilna sredstva
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2010
Varnostne zahteve za vezana brusilna sredstva
Safety requirements for bonded abrasive products
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Exigences de sécurité pour les produits abrasifs agglomérés
Ta slovenski standard je istoveten z: EN 12413:2007/FprA1
ICS:
25.100.70 Brusiva Abrasives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 12413:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2010
ICS 25.100.70
English Version
Safety requirements for bonded abrasive products
Exigences de sécurité pour les produits abrasifs Sicherheitsanforderungen für Schleifkörper aus
agglomérés gebundenem Schleifmittel
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 143.
This draft amendment A1, if approved, will modify the European Standard EN 12413:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12413:2007/FprA1:2010: E
worldwide for CEN national Members.
SI
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.