EN 10272:2016
(Main)Stainless steel bars for pressure purposes
Stainless steel bars for pressure purposes
This document specifies the technical delivery conditions for hot and cold formed stainless steel bars for the construction of pressure equipment supplied in accordance with one of the process routes and surface finishes listed in Table 5.
The general technical delivery conditions in EN 10021 also apply.
NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.
Stäbe aus nichtrostendem Stahl für Druckbehälter
Diese Europäische Norm legt die technischen Lieferbedingungen für warm und kaltgeformte Stäbe aus nichtrostenden Stählen für Druckbehälter nach einer der in Tabelle 6 angegebenen Ausführungsarten und Oberflächenbeschaffenheiten fest.
Zusätzlich gelten die allgemeinen technischen Lieferbedingungen nach EN 10021.
ANMERKUNG Nach Veröffentlichung dieser Norm im EU Amtsblatt (OJEU) unter der Richtlinie 2014/68/EU ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 2014/68/EU auf die technischen Daten von Werkstoffen in dieser Europäischen Norm beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den ESR der Richtlinie 2014/68/EU entsprochen wird.
Barres en acier inoxydable pour appareils à pression
Le présente document spécifie les conditions techniques de livraison des barres en acier inoxydable formées à chaud et à froid destinées à la construction des appareils à pression, livrées conformément à l'une des gammes de fabrication et à l'un des états de surface énumérés au Tableau 5.
Les conditions générales techniques de livraison spécifiées par la norme EN 10021 s’appliquent également.
NOTE Dès lors que la présente Norme européenne est citée dans le Journal Officiel de l’Union européenne (JO) en lien avec la Directive 97/23/CE, la présomption de conformité avec les exigences essentielles de sécurité de la Directive 97/23/CE se limite aux données techniques relatives aux matériaux spécifiées dans la présente Norme européenne et ne suppose pas l’adéquation des matériaux avec un appareil en particulier. Par conséquent, il doit être procédé à l’évaluation des données techniques spécifiées dans la présente norme de matériaux par rapport aux exigences relatives à la conception de cet équipement spécifique, afin de vérifier que les exigences essentielles de sécurité de la Directive 97/23/CE sont satisfaites.
Nerjavne jeklene palice za tlačne posode
Ta dokument določa tehnične pogoje dobave za vroče ali hladno oblikovane nerjavne jeklene palice za konstrukcijo tlačne opreme, dobavljene v skladu z eno od procesnih poti in površinskih obdelav, navedenih v preglednici 5.
Uporabljajo se tudi splošni tehnični dobavni pogoji iz standarda EN 10021.
OPOMBA: Ko bo ta evropski standard objavljen v Uradnem listu Evropske unije (OJEU) v okviru Direktive 97/23/ES, bodo zagotovila o skladnosti z osnovnimi varnostnimi zahtevami (ESR) Direktive 97/23/ES omejena na tehnične podatke o materialih, navedene v tem evropskem standardu, standard pa ne bo zagotavljal ustreznosti materiala za določen element opreme. Zato bo potrebno oceniti tehnične podatke, podane v tem standardu za materiale, glede na zahteve zasnove določenega elementa opreme, da se zagotovi, da so izpolnjene osnovne varnostne zahteve Direktive 97/23/ES.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stäbe aus nichtrostendem Stahl für DruckbehälterBarres en acier inoxydable pour appareils à pressionStainless steel bars for pressure purposes77.140.60Jeklene palice in drogoviSteel bars and rods77.140.30Jekla za uporabo pod tlakomSteels for pressure purposes77.140.20Visokokakovostna jeklaStainless steelsICS:Ta slovenski standard je istoveten z:EN 10272:2016SIST EN 10272:2016en,fr,de01-oktober-2016SIST EN 10272:2016SLOVENSKI
STANDARDSIST EN 10272:20071DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10272
July 2016 ICS 77.140.30; 77.140.60 Supersedes EN 10272:2007
English Version
Stainless steel bars for pressure purposes
Barres en acier inoxydable pour appareils à pression
Stäbe aus nichtrostendem Stahl für Druckbehälter This European Standard was approved by CEN on 15 April 2016.
This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 2016-07-27.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10272:2016 E SIST EN 10272:2016
Guidelines for further treatment (including heat treatment) in fabrication . 31 Annex B (informative)
Tensile strength of austenitic-ferritic steels at elevated temperatures . 35 Annex C (informative)
Reference data of strength values for creep rupture. 36 SIST EN 10272:2016
Significant changes to the previous version EN 10272:2007 . 37 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of Directive 2014/68/EU . 38 Bibliography . 39
Outokumpu OYJ FI – 02200 Espoo, Finland for steel grades 1.4162 and 1.4662 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. CEN shall not be held responsible for identifying any or all such patent rights. CEN and CENELEC maintain online lists of patents relevant to their standards. Users are encouraged to consult the lists for the most up to date information concerning patents (ftp://ftp.cencenelec.eu/EN/IPR/Patents/IPRdeclaration.pdf).
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.