83.140.40 - Hoses
ICS 83.140.40 Details
Hoses
Kunststoffschlauche. Gummischlauche
Tuyaux flexibles
Gumene cevi
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 83.140.40 - Hoses
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies the requirements for two types of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa).
Both types of hose are designed for:
a) use with hydrocarbon fuels, having an aromatic hydrocarbon content not exceeding 50 % by volume and containing oxygenated compounds up to 15 %;
b) operation within the temperature range of −30 °C to +70 °C, undamaged by climatic conditions of −50 °C to 70 °C when stored in static conditions.
This document is not applicable to hoses and hose assemblies for LPG, aviation fuel systems, fuel station systems and marine applications.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for determining the leak tightness and the ease of operation and stop resistance of a valve made of thermoplastic material following an impact applied to the operating device.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for five types of compact, wire-braid-reinforced hoses and hose assemblies of nominal size from 5 to 76. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from 0 °C to +70 °C; — water at temperatures ranging from 0 °C to +70 °C. This document does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. The hose assembly maximum working pressure is governed by the lowest maximum working pressure of the components. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.
- Standard13 pagesEnglish languagesale 15% off
This document specifies design, construction, type and production testing, and marking requirements for both non-insulated cryogenic flexible hoses and insulated vacuum jacketed hoses used for the transfer of cryogenic fluids within the following range of operating conditions:
— working temperature range: from −270 °C to +65 °C;
— nominal size (DN): from 10 to 100.
End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies design, construction, type and production testing, and marking requirements for both non-insulated cryogenic flexible hoses and insulated vacuum jacketed hoses used for the transfer of cryogenic fluids within the following range of operating conditions:
— working temperature range: from −270 °C to +65 °C;
— nominal size (DN): from 10 to 100.
End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the determination of the abrasion resistance of the outer cover of rubber and plastics hoses. This test method is suitable for hoses with inside diameters from 10 mm to 38 mm. This method is not intended for predicting product abrasion life but is suitable for the comparison of like-cover material products.
- Technical specification5 pagesEnglish languagesale 15% off
This document specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies design, construction, type and production testing, and marking requirements for both non-insulated cryogenic flexible hoses and insulated vacuum jacketed hoses used for the transfer of cryogenic fluids within the following range of operating conditions: — working temperature range: from −270 °C to +65 °C; — nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards.
- Standard22 pagesEnglish languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
This document specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies three methods to determine the permeability to gas by measuring the volume of gas diffusing through a rubber or plastics hose or length of tubing used for gas applications in a specified time.
— Method 1 is for determining the permeability of the complete hose wall or length of tubing wall, excluding end fittings, to the test gas.
— Method 2 is for determining the permeability at the hose and fitting interface to the test gas.
— Method 3 is for precisely determining the permeability of the complete hose or length of tubing, including end fittings.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified:
— Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C;
— Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.
The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified:
— Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C;
— Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.
The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 2,5 MPa (25 bar) with an operating-temperature range of −40 °C to +70 °C, depending on the type and category.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from −40 °C up to and including +55 °C at a working pressure of 2,5 MPa (25 bar). It does not include specifications for end fittings and is limited to the performance of the hoses and hose assemblies.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners. The following two types of hose assembly are specified: — Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C; — Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C. The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
This document specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from −40 °C up to and including +55 °C at a working pressure of 2,5 MPa (25 bar). It does not include specifications for end fittings and is limited to the performance of the hoses and hose assemblies.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from −40 °C up to and including +55 °C at a working pressure of 2,5 MPa (25 bar). It does not include specifications for end fittings and is limited to the performance of the hoses and hose assemblies.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies requirements for rubber hoses and tubing for use in the various air and vacuum systems found on internal combustion engines. This document does not cover hoses used for direct power-brake actuation in trucks and trailers, nor for air intakes and ducting within the passenger compartment. The highest-temperature hoses are generally used for turbocharger applications. All hoses and tubing remain serviceable down to −40 °C. NOTE Although the term vacuum is generally used, in reality the application is one of reduced air pressure used for the purposes of actuation or monitoring of the various engine-system components. The air carried by the tubing or hoses can be clean and free of contaminants but can also contain oil, fuel and their vapours as contamination, due to the particular installation and application.
- Standard12 pagesEnglish languagesale 15% off
This document specifies the requirements for rubber hoses and hose assemblies used for low-pressure application of circulating gaseous Refrigerant 1234yf (tetrafluoropropene) (hereinafter referred to as R1234yf) in the air-conditioning systems of automobiles. The hoses and hose assemblies are designed in such a way as to reduce vibration transmission between the engine room and the cabin. The operational temperature range is −40 °C to +80 °C. Due to the critical relationship between the hose and coupling for this application, a requirement that the coupling to be used in service be used for testing is laid down.
- Standard29 pagesEnglish languagesale 15% off
This document specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). This document is applicable to the following types of hose: — type 1: rubber hoses for unheated water supply (maximum temperature 70 °C); — type 2: rubber hoses for heated water supply (maximum temperature 90 °C); — type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). NOTE National requirements for hose fittings and hoses conveying drinking water can apply.
- Standard13 pagesEnglish languagesale 15% off
This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose made out of rubber or thermoplastic elastomer (TPE).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar.
This document is not applicable to multi chamber fuel dispensing hoses.
NOTE As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 is carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.
1 bar = 0,1 MPa.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides a scheme for the assessment of conformity of RFC products for the rehabilitation of existing pipelines, in accordance with the applicable parts of ISO 11296, ISO 11297 and ISO 11298, and intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It applies to cured-in-place pipe (CIPP) products only. It applies to non-pressure pipe liners, and to independent (fully structural, class A) and interactive (semi-structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline.
NOTE In order to help the reader, summary tables of overall scheme requirements are provided in Annex E.
- Technical specification39 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides a scheme for the assessment of conformity of PVC-U products and assemblies for the rehabilitation of existing pipelines, in accordance with the applicable parts of ISO 11296 and intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, summary tables of overall scheme requirements are provided in Annex C.
- Technical specification30 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines terms used in the hose industry.
Recommended terminology for electrical conductivity and resistance of rubber and plastics hoses and hose assemblies can be found in ISO 8031:2020, Annex A.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies requirements for five types of textile-reinforced hydraulic hoses and hose assemblies of nominal size from 5 to 100.
They are suitable for use with:
— oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +100 °C;
— water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +70 °C;
— water at temperatures ranging from 0 °C to +70 °C.
This document does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesEnglish languagesale 15% off
This document specifies requirements for standard-weight polytetrafluoroethylene (PTFE) hose assemblies for use in aircraft hydraulic systems at temperatures between –55 °C and +204 °C and at a nominal pressure up to 21 000 kPa (210 bar). The hose assemblies are also suitable for use within the same temperature and pressure limitations in aircraft pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated.
- Standard17 pagesEnglish languagesale 15% off
This document specifies requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aircraft hydraulic systems at temperatures between –55 °C and +204 °C and at a nominal pressure up to 28 000 kPa (280 bar). The hose assemblies are also suitable for use within the same temperature and pressure limitations in aircraft pneumatic systems where some gaseous diffusion through the wall of the PTFE liner may be tolerated.
- Standard17 pagesEnglish languagesale 15% off
This document specifies a method for the determination of the volumetric expansion of rubber or plastics hoses under hydrostatic pressure.
This document does not specify the dimensions of the test piece and the test pressure(s) as each of which is specified in the appropriate specification.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge.
NOTE All pressures are expressed in megapascals and in bar (1 MPa = 10 bar).
Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8).
Type A (rubber) hoses are intended for use at a minimum temperature of −20 °C and Type B (thermoplastics) hoses are intended for use at a minimum temperature of −10 °C.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore sizes from 25 mm to 300 mm, working pressures from 0,4 MPa (4 bar) to 1,4 MPa (14 bar) and working temperatures from −30 °C to 150 °C, according to type. Type 1 hoses are suitable for vapour applications. Types 2 to 4 hoses are suitable for liquid applications. NOTE 1 See Annex A concerning the selection of the material for the inner wall of layers and any polymeric coating of the internal wire helix related to the chemical(s) to be conveyed by the hoses and/or hose assemblies. NOTE 2 It is intended that the manufacturer be consulted where a polymeric coated internal wire is being considered for use with low conductivity hydrocarbons or chemicals. This document does not apply to hoses and hose assemblies for: — aircraft refuelling (see ISO 1825); — fuel dispensing (see ISO 5772); — oil burners (see ISO 6806); — liquefied petroleum gas and liquefied natural gas (see ISO 27127); — fire fighting (see ISO 14557); — offshore liquefied natural gas (see EN 1474-2); — refrigeration circuits.
- Standard23 pagesEnglish languagesale 15% off
This document specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore. — Class A hose is for use onshore. — Class B hose is for use offshore. This document is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from −196 °C to +45 °C, according to class. NOTE Offshore liquefied natural gas (LNG) hose assemblies are also specified in EN 1474-2. EN 1474-2 does not only specify offshore use, but also ship to shore and other LNG transfer applications.
- Standard20 pagesEnglish languagesale 15% off
This document specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air braking systems (see ISO 7628), fuel lines (see ISO 13775-2), and high-pressure hydraulic systems. This document is intended especially for use by original equipment manufacturers (OEMs).
- Standard13 pagesEnglish languagesale 15% off
This document specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 1,0 MPa (10 bar). Both groups of hoses are designed for a) use with hydrocarbon fuels having an aromatic-hydrocarbon content not exceeding 50 % by volume and containing up to 15 % of oxygenated compounds, and b) operation within the temperature range of −30 °C to +70 °C, undamaged by climatic conditions of −50 °C to +70 °C when stored in static conditions. NOTE Hoses for use at temperatures lower than −30 °C can be the subject of discussion between manufacturer and end user. This document is not applicable to hoses and hose assemblies for LPG systems, aviation fuel systems, fuel station systems or marine applications.
- Standard14 pagesEnglish languagesale 15% off
This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6605:2017 specifies uniform test methods for evaluating the performance of hoses and hose assemblies (hoses and attached hose fittings) used in hydraulic fluid power systems.
Specific tests and performance criteria for evaluating hoses and hose assemblies used in hydraulic applications are in accordance with the requirements of the respective product (hoses or hose fitting) specifications.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document establishes the requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. These hoses can also be used manually to supply unpressurized water to the pump or for water discharge. NOTE All pressures are expressed in megapascals and in bar (1 MPa = 10 bar). Additional requirements are specified for hose assemblies, that is, hoses with couplings already fitted, where this is carried out by the hose manufacturer (see Clause 8). Type A (rubber) hoses are intended for use at a minimum temperature of −20 °C and Type B (thermoplastics) hoses are intended for use at a minimum temperature of −10 °C.
- Standard18 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This document describes the specific functional requirements for polyamide (PA) pipelines in addition to the general functional requirements of EN 12007-1 for:
a) a maximum operating pressure (MOP) up to and including 16 bar;
b) an operating temperature between −20 °C and +40 °C.
This document covers one type of pipe:
- PA pipes single layer solid wall.
This document specifies common basic principles for gas infrastructure.
NOTE 1 Users of this document are aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
NOTE 2 In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
CEN/TR 13737 (all parts) give:
- clarification of all legislations/regulations applicable in a member state;
- if appropriate, more restrictive national requirements;
- a national contact point for the latest information.
- Technical specification26 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for three types of textile-reinforced thermoplastics hoses and hose assemblies of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements.
They are suitable for use with:
— oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +93 °C;
— water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from 0 °C to +60 °C
— water at temperatures ranging from 0 °C to +60 °C.
This document does not include any requirements for end fittings. It is limited to the performance of hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for two types of hose assemblies (Types D and SD) and four grades based on electrical properties with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous chemical substances, hereinafter termed the "chemicals conveyed".
The hose assemblies are intended for use with chemicals conveyed in the temperature range of -20 °C to +65 °C at a working pressure ≤ 10 bar1.
NOTE 1 This document sets out requirements for these hose assemblies to ensure that users are not exposed to danger from fire or explosion and that the environment is protected against contamination or damage.
NOTE 2 Other temperatures and working pressures than those given above can be agreed with the manufacturer, provided that the marking on the hose (see 14.1) states this and the requirements of Table 5 and all the other requirements are met.
NOTE 3 Other diameters than those given in this document can be agreed with the manufacturer.
NOTE 4 This document also provides guidance on the storage of hose assemblies (Clause 15).
NOTE 5 The attention of users is drawn to Annex F concerning the selection of lining material related to the chemical(s) to be conveyed by the hoses and/or hose assemblies.
This document does not apply to hose assemblies for:
- aircraft refuelling (EN ISO 1825);
- fuel dispensing (EN 1360);
- oil burners (EN ISO 6806);
- refrigerant circuits;
- fuel truck delivery (EN 1761);
- liquid petroleum gases (LPG) (EN 1762, EN 16436-2);
- fire-fighting (EN ISO 14557);
- oil suction and discharge (EN 1765);
- rotary drilling (EN ISO 6807);
- fuel dispensing with vapour recovery systems (EN 13483);
- anhydrous ammonia (EN ISO 5771).
This document does not apply to multilayer hose assemblies (EN 13765 and EN 13766).
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 2,5 MPa (25 bar) within the temperature range −30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C.
- Standard12 pagesEnglish languagesale 15% off
This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.
- Standard7 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
This document provides a scheme for the assessment of conformity of PE products and assemblies for the rehabilitation of existing pipelines, in accordance with the applicable parts of ISO 11296, ISO 11297, ISO 11298, ISO 11299 and ISO 21225, and intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, summary tables of overall scheme requirements are provided in Annex E.
- Technical specification54 pagesEnglish languagesale 10% offe-Library read for1 day
2017-08-31 - BTC 110/2017 - BT approve publication of EN ISO with modified Annex ZA & Foreword
2017-08-08 - Cannot allocate for publication due to negative assessment from Consultant.
CEN/BT C082/2011: DOW = DAV + 36 months
- Amendment11 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides specification and testing requirements for high pressure flexible hose assemblies intended to be connected to gas cylinders, bundles of cylinders or trailers (battery vehicles), and MEGCs for use when filling and emptying gas at production sites and also for customer use. This document applies to flexible hose assemblies with rated pressures up to 1 000 bar for use in the temperature range of −40 °C to +65 °C.
This document is not applicable to:
— rubber and plastics flexible hose assemblies for welding, cutting and related processes up to 45 MPa (450 bar) for customer use (see ISO 14113);
— high pressure flexible hose assemblies for use with medical gas systems for customer use (see ISO 21969);
— low pressure hose assemblies for use with medical gases for customer use (see ISO 5359);
— rubber and thermoplastic low pressure hose assemblies for welding, cutting and related processes for customer use (see ISO 3821 or ISO 12170);
— flexible hose assemblies for cryogenic applications (see ISO 21012);
— flexible hose assemblies for liquid petroleum gas (LPG).
NOTE Flexible hose assembly designs which pass the type test approval described in this document can have a lower ratio of burst pressure to rated pressure than stated in other standards.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day