IEC/TC 116 - Safety of hand-held motor-operated electric tools
To prepare international safety standards for electric motor-operated hand-held tools, transportable tools and lawn and garden machinery.
Varnost električnih ročnih orodij
To prepare international safety standards for electric motor-operated hand-held tools, transportable tools and lawn and garden machinery.
General Information
- 1 (current)
- 2
- 3
- 4
- 5
IEC 62841-2-7:2024 deals with the safety of electric motor-operated hand-held spray guns for non-flammable materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-7 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-12:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete vibrators. IEC 62841-1:2014, Clause 1 is applicable, except as follows. Addition: This document applies to hand-held concrete vibrators.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is applicable, except as follows: Addition: This document applies to hand-held and backpack - garden blowers; - garden vacuums; and - garden blower/vacuums. This document does not apply to - walk-behind garden blowers, walk-behind garden vacuums and walk-behind garden blower/vacuums; - robotic garden blowers, robotic garden vacuums and robotic garden blower/vacuums; and - vacuum cleaners intended primarily for use indoors, for water suction cleaning or animal grooming. NOTE 101 Vacuum cleaners and water-suction cleaning appliances, including vacuum cleaners for animal grooming are covered by IEC 60335-2-2. NOTE 102 Vacuum cleaners for commercial use are covered by IEC 60335-2-69.
- Standard71 pagesEnglish languagesale 10% offe-Library read for1 day
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series
2021-12-14: Common mods to this prA1 are included in prAB (PR=75448)
- Amendment13 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-4-7:2022 clause 1 of IEC 62841-1:2014, is applicable, except as follows: Addition: This document applies to pedestrian controlled walk-behind lawn scarifiers and lawn aerators which are designed for regenerating lawns by combing out materials such as grass, thatch and moss or cutting vertically into the lawn face using
metallic tines; and/or
rigid non-metallic tines which rotate about a horizontal axis. This document does not apply to
pedestrian controlled walk-behind lawnmowers;
towed/semi-mounted lawn scarifiers and lawn aerators;
ride-on machines;
non-powered lawn scarifiers and lawn aerators;
combustion engine powered lawn scarifiers and lawn aerators;
plug aerators (corers);
hybrid and fuel cell powered machines and associated charging systems; and
garden tractors or their attachments.
- Standard91 pagesEnglish languagesale 10% offe-Library read for1 day
2022-04-01- HD: NEXT ACTION: TB ACTION (2nd FV draft sent to production on 2022-03-25)
2020-06-16: Common mods to this prA1 are included in prAC (PR=72183)
DOW=DOR+48 months
- Amendment20 pagesEnglish languagesale 10% offe-Library read for1 day
No scope available
- Amendment43 pagesEnglish languagesale 10% offe-Library read for1 day
2020-12-14: Common mods to this EN IEC are included in prAA (PR=73229) for simultaneous circulation
D164/C043: DOW=DOR+48 months
- Amendment13 pagesEnglish languagesale 10% offe-Library read for1 day
2020-12-24: Common mods to this prA1 are included in prAB (PR=73280) for simultaneous circulation
D164/C043: DOW= dor + 48 months
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-5:2022 applies to band saws intended for cutting wood and analogous materials, plastics and metals, except magnesium. This document does not apply to transportable scroll saws and jig saws with a reciprocating blade. This document does not apply to
hand-held band saws;
non-vertical saws; and
wire saws. NOTE 101 It is planned that a document on transportable scroll saws and jig saws will be published. NOTE 102 Hand-held band saws will be covered by a future part of IEC 62841-2. NOTE 103 In Europe (EN IEC 62841-3-5), the following conditions apply: This document does not apply to stationary band saws intended to cut wood and similar materials. Stationary band saws that are intended to cut wood and similar materials are covered by EN 1807-1. This document applies to band saws having a mass of: - maximum 25 kg for tools capable of being lifted by hand by one person; - maximum 50 kg for tools capable of being lifted by hand by two persons.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard does not apply to rotary hammers, even if they can be used as a drill. This Part 2-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drill, Impact Drill, Hand-held tool, Safety
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-17:2017 applies to routers intended for cutting slots into or shaping the edge of various materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This part of IEC 62841 does not apply to jointers. Routers that are primarily used for trimming the edge of materials are also known as trimmers. Routers that are used to cut various materials through the rotary action are also known as rotary cutters. This Part 2-17 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Router, Trimmer, Hand-held tool, Safety
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-4-5:2021 This document applies to grass shears with a maximum cutting width of 200 mm designed primarily for cutting grass. This document does not apply to hedge trimmers. Hedge trimmers are covered by IEC 62841-4-2.
- Standard73 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-14:2017 applies to transportable drain cleaners. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Drain cleaners are also known as pipe cleaners. This standard does not apply to hand-held drain cleaners. Hand-held drain cleaners are covered by IEC 62841-2-21. This standard does not apply to high pressure cleaners to clean drains. High pressure cleaners are covered by IEC 60335-2-79. This standard does not apply to machines that use a solid rod to clean drains This Part 3-14 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-4-3:2020 This document applies to the design of pedestrian controlled walk-behind - cylinder lawnmowers; and - rotary lawnmowers equipped with - metallic cutting means; and/or - rigid non-metallic cutting means; and/or - non-metallic cutting means with one or more cutting elements pivotally mounted on a generally circular drive unit, where these cutting elements rely on centrifugal force to achieve cutting, and have a kinetic energy for each single cutting element of greater than 10 J. This document does not apply to - robotic lawnmowers; - remote-controlled lawnmowers; - flail mowers or flail-type attachments; - scissors type lawnmowers; - grassland mowers; - sickle bar mowers; - towed/semi-mounted grass-cutting machines; - scrub-clearing machines; - lawn trimmers and lawn edge trimmers; - lawn edgers; - grass trimmers; - brush cutters; - brush saws; - agricultural mowers; - trailing seat/sulky units; - ride-on machines; - non-powered lawnmowers; - combustion engine powered lawnmowers; - hybrid and fuel cell powered machines and associated charging systems; and - garden tractors or their attachments. Robotic lawnmowers are covered by IEC 60335-2-107, and will be covered by a future part of IEC 62841.
- Standard116 pagesEnglish languagesale 10% offe-Library read for1 day
No scope available
- Amendment11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-3:2020: applies to hand-held grinders, disc-type polishers and disc-type sanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity. This standard does not apply to dedicated cut-off machines. This standard does not apply to orbital polishers and orbital sanders. This standard does not apply to die grinders. This Part 2-3 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard70 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-7:2020 This document applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to transportable wall saws that are intended to be left unattended while performing an operation. This document does not apply to transportable wall saws that employ hydraulic systems. This document does not apply to hand-held cut-off machines.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-13:2017 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. This Part 3-13 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drills, Hand-held tool, Safety
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-10:2017 applies to mixers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Mixers are not considered to be tools with a liquid system. This standard does not apply to drills and impact drills, even if they can be used as a mixer This Part 2-10 is to be used in conjunction with the first edition of IEC 62841-1:2014 . The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Mixer, Hand-held tool, Safety
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-6:2020 Tools covered by this document include percussion hammers and rotary hammers, including rotary hammers with the capability to rotate only with the percussion system disengaged (drill only mode). The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to drills and impact drills. This document does not apply to tools that are designed exclusively for driving fasteners, such as palm nailers.
- Standard60 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-9:2020 is available as IEC 62841-3-9:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62841-3-9:2020 applies to transportable mitre saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 410 mm, which hereinafter might simply be referred to as saw or tool. This International Standard does not apply to mitre saws intended to cut other metals, such as magnesium, steel and iron. This document does not apply to mitre saws with an automatic feeding device. Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3. This document does not apply to saws designed for use with abrasive wheels. Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10. This document does not apply to tools combining the function of a mitre saw with the function of a table saw. Transportable tools combining the function of a mitre saw with the function of a table saw are covered by by a future part of IEC 62841-3. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Clause 1: Scope: increase of the maximum saw blade diameter to 410 mm; - Corrigendum 1 and Corrigendum 2 of the first edition have been incorporated in this second edition. This Part 3-9 is to be used in conjunction with the IEC 62841-1:2014. Key words: Hand-Held Tools, Transportable Mitre Saw
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-06 JF: the Annex ZZ which had been approved by the BT is not the most recent one -> need to submit the correct Annex ZZ to the BT. The BT document under preparation.
2019-11-05 JF: Through the BT decision D163/C100, the BT approved the revised Annex ZZ of the standard. Standard under publlication.
NEXT ACTION: CCMC ACTION BY 2019-08-30: submission of the revised Annex ZZ for the BT approval.
Compliant assessment of the Annex ZA received.
2019-05-08 JF: HAS Consultants confirmed that the request for assessment will be accepted but asked to issue a new request by CCMC. CCMC made a new request. The indicative deadline to receive it: 2019-06-12
2019-04-19 JF: EC clarified that HAS Consutlants will carry out the assessment of the corrected Annex ZZ. NEXT ACTION: HAS CONSULTANT ASSESSMENT EXPECTED BY 2019-05-23.
2019-01-30 Assessment request rejected by HAS Consultants on the grounds that it is a second requset at this stage. CCMC asked the EC to clarify.
2019-
- Amendment9 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-8:2016 applies to hand-held shears and nibblers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Keywords: Shear, Nibbler, Hand-held tool, Transportable tool This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-4-1:2017 applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. This standard does not apply to chain saws for tree service as defined in ISO 11681-2; or pole-mounted pruners. Pole-mounted pruners will be covered by a future part of IEC 62841. The chain saws covered by this standard are designed only to be operated with the right hand on the rear handle and the left hand on the front handle. This Part 4-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard68 pagesEnglish languagesale 10% offe-Library read for1 day
Next steps: the formal vote of the European Amendment
2019-08-08 JF: The Annex ZZ was delivered after the Enquiry started. The need to adapt the Annex ZZ.
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-11:2015 applies to applies to reciprocating saws such as jig saws and sabre saws.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-11 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: reciprocating saw, jig saw, sabre saw, hand-held tool, transportable tool
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-10:2015(E) applies to transportable cut-off machines intended to cut materials such as metals, concrete and masonry and to be fitted with one abrasive bonded reinforced wheel of Type 41, or diamond cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm and with a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the maximum wheel diameter and a wheel diameter range of 250 mm to 410 mm. This standard does not apply to: - transportable mitre saws; - transportable tile saws or transportable metal saws. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. This publication is to be read in conjunction with IEC 62841-1:2014. Key words: Hand-held tools, Transportable tools, Cut-off machines
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-14:2015(E) applies to hand-held planners the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-14 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Planner, Hand held, Cutting head
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-9:2015 applies to hand-held tappers and threaders. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Tapper, Threader, Internal Screw Threads, External Screw Threads This publication is to be read in conjunction with
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-2:2014 deals with the safety of electric motor-operated or magnetically driven hand-held screwdrivers and impact wrenches. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-2 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Hand-held, Screwdriver, Impact wrench
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-1:2014 applies to transportable table saws with: - a toothed single blade; or - stacked blades that cut a single groove or slot; or - a moulding head cutter intended for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter between 105 mm and 315 mm, which hereinafter may simply be referred to as saw or tool. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This standard does not apply to table saws intended to cut other metals, such as magnesium, steel and iron. This standard does not apply to table saws with an automatic feeding device. This standard does not apply to saws designed for use with abrasive wheels. This standard does not apply to table saws with more than one spindle such as for a scoring blade. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Table Saw, Transportable This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard55 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-5:2014 applies to hand-held circular saws. This standard does not apply to saws designed for use with abrasive wheels. Saws designed for use with abrasive wheels as cut-off machines are covered by IEC 62841-2-22. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Saw, Circular, Cutting, This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard46 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-6:2014 applies to transportable diamond drills, intended to be connected to a liquid system. The liquid system may include liquid from a pipe or container. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This Part 3-6 is to be used in conjunction with IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Diamond drill, Drill unit, Drill stand
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-4:2014 applies to hand-held sanders and polishers with the exception of disc-type tools covered by IEC 62841-2-3. Tools covered by this standard include but are not limited to belt sanders, drum sanders or polishers, reciprocating sanders or polishers, orbital sanders or polishers and random orbit sanders or polishers. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Sander, Polisher, Belt, Drum Orbital, Reciprocating, Random Orbit This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-4-2:2017 applies to hand-held hedge trimmers which are designed for use by one operator for trimming hedges and bushes, including extended-reach hedge trimmers with a maximum length of 3,5 m. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard is not applicable to hedge trimmers with a rotating blade. This standard is not applicable to scissors type grass shears. This Part 4-2 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Hedge trimmer, Hand-held tool, Safety
- Standard94 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-12:2017 applies to transportable threading machines. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 3-12 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Threading Machine, Hand-held tool, Safety
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-1:2014 deals with the safety of electric motor-operated or magnetically driven: - hand-held tools (IEC 62841-2); - transportable tools (IEC 62841-3); - lawn and garden machinery (IEC 62841-4). The above listed categories are hereinafter referred to as 'tools' or 'machines'. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Tools with electric heating elements are within the scope of this standard. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard is scheduled to cancel and replace the fourth edition of IEC 60745-1, published in 2006, the first edition of IEC 61029-1, published in 1990, and the fifth edition of IEC 60335-1, published in 2010, only with respect to requirements concerning lawn and garden machinery. The latter publications remain valid until they are withdrawn. This standard constitutes a technical revision. This edition includes the following significant technical changes with respect to the fourth edition of IEC 60745-1: - requirements in various clauses introduced or modified in order to include the requirements for transportable tools and lawn and garden machinery (formerly covered by IEC 61029-1 and IEC 60335-1); - leakage current test and electric strength test moved from former Clauses 13 and 15 to Annexes C and D; - former Clauses 29, 30 and 31 renumbered to become Clauses 6, 13 and 15; - requirements for electronic safety critical functions added to Clause 18; - requirements for switches revised and moved from Annex I to Clause 23; - clarifications in respect to soft materials (elastomers) added to Clauses 9, 19 and 13; - test finger in Figure 1 of IEC 60745-1 and test probe in Figure 2 of IEC 60745-1 replaced by references to basic IEC standards; - requirements for Li-Ion battery systems added to Annexes K and L and Annex M was removed. Key words: Tools, Electric-Motor-Operated, Hand held, Transportable, Lawn and Garden
- Standard186 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-2-21:2017 applies to hand-held drain cleaners (drain cleaners are also known as pipe cleaners) the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard does not apply to transportable drain cleaners. This standard does not apply to machines that use a solid rod to clean drains. This Part 2-21 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is replaced by the following: This European Standard specifies safety requirements and their verification for the design and construction of robotic battery powered electrical rotary lawnmowers and their peripherals with the rated voltage of the battery being not more than 75 V d.c. charged by mains electrical and/or alternative energies, e.g. solar power. This European Standard does not apply to non-robotic machines such as lawn trimmers, lawn edge trimmers, lawn edgers, ride-on lawnmowers or pedestrian controlled lawnmowers. This European Standard is not applicable to EMC and environmental hazards (except noise). This European Standard does not apply to internal combustion engine(s), hybrid and fuel cell powered machines and associated charging systems. This European Standard deals with all the significant hazards presented by battery powered robotic lawnmowers and their peripherals when they are used as intended and under conditions of misuse which are reasonably foreseeable. This European Standard is not applicable to machines, which are manufactured before the date of publication of this document by CENELEC. NOTE This European Standard does not apply to battery chargers (EN 60335-2-29:2004).
- Standard72 pagesEnglish languagesale 10% offe-Library read for1 day
Replacement: This European Standard specifies the safety requirements and their verification for the design and construction of hand-held mains-operated electrical garden vacuums, and garden blower/vacuums with or without shredding means and garden blowers, hereinafter referred to as machine(s), for use at and around the home or for similar purposes, their rated voltage being not more than 250 V single phase. This European Standard does not apply to: - machines powered by combustion engines; NOTE 1 Combustion engine driven machines are covered by EN 15503. - machines driven by an external power source; - machines powered from a 3 phase supply; - vacuum cleaners intended primarily for use indoors, for water suction cleaning or animal grooming; NOTE 2 EN 60335-2-2 deals with this type of machine. - walk-behind, hand-guided (support-wheeled) and ride-on machines; - combination of a mains driven and/or battery powered blowers and vacuums with internal combustion engines (hybrid); - back-pack powered blowers and back-pack powered vacuums. EMC and environmental aspects, except noise, have not been considered in this standard. This European Standard deals with all the significant hazards presented by hand-held mains-operated electrical garden vacuums, garden blower/vacuums with or without shredding means and garden blowers when they are used as intended and under conditions of misuse which are reasonably foreseeable. This European Standard is not applicable to machines, which are manufactured before the date of publication of this document by CENELEC.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is replaced by the following. This European Standard specifies safety requirements and their verification for the design and construction of electric powered hand-held scissors type grass shears with a maximum cutting width of 200 mm designed primarily for cutting grass, their rated voltage being not more than 250 V for a.c. or 75 V d.c. In this European Standard the term “machine” means “electric powered scissors type grass shear”. This European Standard does not apply to hedge trimmers as covered by EN 60745–2–15. Requirements for chargers are covered by EN 60335-2-29:2004. Requirements for batteries are covered by EN 62133:2003. EMC and environmental aspects except for noise have not been considered in this European Standard. This European Standard deals with all the significant hazards presented by hand-held scissors type grass shears when they are used as intended and under conditions of misuse which are reasonably foreseeable.
- Standard50 pagesEnglish languagesale 10% offe-Library read for1 day
Deals with the safety of pedestrian-controlled mains-operated electric lawn scarifiers and aerators. These scarifiers have rotating cutters for regenerating lawns by, for instance, combing out grass thatch and moss, or by cutting vertically into the lawn face. These scarifiers are designed primarily for home use, with a rated voltage not more than 250 V single phase. For lawnmowers, see IEC 60335-2-77; for lawn trimmers, see IEC 60335-2-91. The contents of the corrigendum of May 2003 have been included in this copy.
- Standard61 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is replaced by the following. This European Standard specifies safety requirements and their verification for the design and construction of electric powered walk-behind and hand-held lawn trimmers and lawn edge trimmers, with cutting element(s) of non metallic filament line or freely pivoting non-metallic cutter(s), with a kinetic energy of not more than 10 J each, used by a standing operator for cutting grass, their rated voltage being not more than 250 V for a.c. or 75 V d.c.. NOTE 101 The method of calculating the kinetic energy for the purposes of this standard is given in 22.103. In this European Standard, hand-held and walk-behind lawn trimmers and lawn edge trimmers are referred to collectively as machine(s). This European Standard does not apply to - scissor type or lawn trimmers and lawn edge trimmers with cutting means other than those described above; - lawn trimmers and lawn edge trimmers with collecting devices; - self-propelled lawn trimmers or lawn edge trimmers; EMC and environmental aspects, except noise, have not been considered in this European Standard. This European Standard does not apply to chargers as covered by EN 60335-2-29. This European Standard does not apply to batteries as covered by EN 62133. This European Standard deals with all the significant hazards presented by hand-held and walk-behind lawn trimmers and lawn edge trimmers when they are used as intended and under conditions of misuse which are reasonably foreseeable.
- Standard50 pagesEnglish languagesale 10% offe-Library read for1 day
2013-07-10 - Publication editing allocated to cpalagi@cencenelec.eu 2013-02-04 - UAP text to be sent to Consultant prior to UAP D144/C006: NWI approved*2013-03-22: UAP processing allocated to aclausse@cencenelec.eu
2021: CLC legacy converted by DCLab NISOSTS
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62841-3-4:2016 applies to transportable bench grinders that can be equipped with one or two accessories as follows: - type 1 grinding wheels in accordance with ISO 603-4:1999 with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm; - wire brushes with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm; - polishing wheels with a diameter not exceeding 310 mm and with a peripheral speed of any accessory between 10 m/s and 50 m/s. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Keywords: Bench Grinder, Hand-held tool, Transportable tool This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
2013-01-23 - Publication editing allocated to cpalagi@cencenelec.eu
- Amendment10 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60745-2-23:2012 applies to die grinders and small rotary tools for mounted accessories not exceeding 55 mm in diameter and mounted sanding accessories not exceeding 80 mm in diameter such as, threaded cones or plugs that are threaded on a mandrel with an unrelieved shoulder flange, mandrel mounted wheels and rotary files with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity. This part 2 is to be used in conjunction with the latest edition of IEC 60745-1 and its amendments. It was established on the basis of the fourth edition (2006) of that standard. This standard does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory. Those tools are covered by IEC 60745-2-3. Keywords: Die grinders, rotary tools, grinding, sanding.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
Applies to combined mitre-bench saws intended for cutting non-ferrous metals such as aluminium, wood or similar materials. The blade diameter does not exceed 350 mm.
- Standard65 pagesEnglish languagesale 10% offe-Library read for1 day
Applies to transportable band saws having a length of saw band not more than 2 500 mm and band wheels having a diameter of not more than 315 mm.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
- 1 (current)
- 2
- 3
- 4
- 5