EN 60745-2-22:2011

SLOVENSKI STANDARD
01-september-2011
(OHNWULþQDURþQDRURGMD9DUQRVWGHO3RVHEQH]DKWHYH]DUH]DOQLNH
Hand-held motor-operated electric tools - Safety - Part 2-22: Particular requirements for
cut-off machines
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-22: Besondere
Anforderungen für Trennschleifmaschinen
Outils électroportatifs à moteur - Sécurité - Partie 2-22: Règles particulières pour les
tronçonneuses à disques
Ta slovenski standard je istoveten z: EN 60745-2-22:2011
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60745-2-22
NORME EUROPÉENNE
June 2011
EUROPÄISCHE NORM
ICS 25.140.20
English version
Hand-held motor-operated electric tools -
Safety -
Part 2-22: Particular requirements for cut-off machines
(IEC 60745-2-22:2011, modified)

Outils électroportatifs à moteur -  Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-22: Règles particulières pour les Sicherheit -
tronçonneuses à disques Teil 2-22: Besondere Anforderungen für
(CEI 60745-2-22:2011, modifiée) Trennschleifmaschinen
(IEC 60745-2-22:2011, modifiziert)

This European Standard was approved by CENELEC on 2011-04-18. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-22:2011 E
Foreword
The text of document 116/57/FDIS, future edition 1 of IEC 60745-2-22, prepared by IEC TC 116, Safety of
hand-held motor-operated electric tools, was submitted to the IEC-CENELEC parallel vote.
A draft amendment, prepared by the Technical Committee CENELEC TC 116, Safety of motor-operated
electric tools, was submitted to the formal vote.
The combined texts were approved by CENELEC as EN 60745-2-22 on 2011-04-18.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2012-04-18
– latest date by which the national standards conflicting
(dow) 2014-04-18
with the EN have to be withdrawn
This European Standard is divided into two parts
Part 1: General requirements which are common to most hand-held electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of this
standard;
Part 2: Requirements for particular types of tools which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
This draft European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of EC Directive
2006/42/EC. See Annex ZZ.
Compliance with the clauses of Part 1 together with this Part 2-22 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EC Directives can be applicable to the products falling within
the scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.
This Part 2-22 is to be used in conjunction with EN 60745-1:2009. When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
Subclauses and figures which are additional to those in Part 1 are numbered starting from 101; additional
annexes are lettered AA, BB, etc.
Subclauses, tables and figures which are additional to those in IEC 60745-2-22 are prefixed “Z”.
Annexes ZA and ZZ have been added by CENELEC.
NOTE In this standard, the following print types are used:
- Requirements: in roman type;
- Test specification: in italic type;
- Notes: in smaller roman type.

- 3 - EN 60745-2-22:2011
Endorsement notice
The text of the International Standard IEC 60745-2-22:2011 was approved by CENELEC as a European
Standard with agreed common modifications as given below.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60745-2-3 NOTE  Harmonized as EN 60745-2-3.
IEC 60745-2-5 NOTE  Harmonized as EN 60745-2-5.
COMMON MODIFICATIONS
2 Normative references
Add the following normative reference:
EN 1339:2003, Concrete paving flags - Requirements and test methods
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable except as follows:
6.1.2.4 Modification:
Cut-off machines are held and used as specified in 6.1.2.5 and described in Table Z101. The concrete
block, its support and the tool shall be so oriented that the geometric centre of the tool is 1 m above the
reflecting plane (dimension “y” in Figure Z102). The centre of the concrete block shall be located under
the top microphone.
6.1.2.5 Modification:
Cut-off machines are tested under load observing the conditions shown in Table Z101.

Table Z101 — Operating conditions for cut-off machines
Material and set up Concrete slab with minimum dimensions of 400 mm x 600 mm and a thickness of
(50 ± 5) mm according to EN 1339. The concrete slab shall be stored under dry
conditions for at least 28 days and have the following specifications in accordance
with the following clauses of EN 1339:
Class 3 (5.3.3.2), Class 4 (5.3.4.2), Class 70 (5.3.6.2).
The concrete slab is rigidly fixed on a supporting concrete block with the minimum
dimensions of 800 mm x 500 mm x 200 mm e.g. by means of clamps.
At the beginning of the test the end of the concrete slab shall project 200 mm from
the concrete block and shall be readjusted at least after each series of tests.
Unless the machine is intended for operation with water supply, the dust shall be
collected during operation using a vacuum system. This shall be in place and fitted
correctly. The hose for dust extraction shall be connected and have adequate length
to eliminate the influence of the noise and vibration from the vacuum system on the
tool measurements.
See Figures Z102 and Z103.
Orientation Cutting the concrete slab across the 400 mm width with the entire surface of the
guide plate or all guide rollers being in contact with the concrete slab.
The cut shall not be less than 20 mm from the edge of the slab.
Tool bit/settings New wheel(s) as specified for cutting concrete. If the tool is intended to be used with
more than one wheel, then maximum number of wheels shall be fitted and set to the
maximum width of cut.
Speed setting devices, if any, shall be adjusted to the setting specified for cutting-off
concrete.
The depth gauge, if any, shall be adjusted to a cutting depth equal to the thickness
of the slab(s) plus 40 mm.
If no depth gauge is provided, the cut shall be made with a cutting depth of the
slab(s) plus approximately 10 mm to 40 mm.
If the maximum cutting depth of the cut-off machine is less than the values above,
the test is conducted at maximum cutting depth.
Feed force The forces applied to the tool shall be sufficient to obtain rated input/current ± 10 %
during cutting, applying approximately equal forces to both handles.
If either the input/current above cannot be achieved or the test cycle is less than 5 s,
the test shall be conducted on two slabs stacked together.
Excessive grip forces shall be avoided.
Test cycle One cut across the 400 mm width of the concrete slab.
Measurement starts when the wheel enters the concrete slab and finishes when the
wheel leaves the slab.
- 5 - EN 60745-2-22:2011
6.2 Vibration
6.2.4.2 Location of the measurement
Addition:
Figure Z101 shows the positions on the handles of different types of cut-off machines.
6.2.6.3 Operating conditions
Modification:
Cut-off machines intended to cut materials such as concrete, brick and masonry are tested under load
observing the conditions shown in Table Z101. The top of the slab shall have a distance to the ground of
maximum 450 mm (dimension “x” in Figure Z102).
6.2.7.2 Declaration of the vibration emission value
Addition:
The vibration emission value a of the handle with the highest emission and the uncertainty K shall be
h
declared.
8 Marking and instructions
8.12.2 a) Add the following items:
Z101) Instruction on the correct use of the dust collection system unless the machine is intended for
operation with a liquid system
Z102) Instruction to wear a dust mask unless the machine is intended for operation with a liquid system
Z103) Instruction to always wear hearing protection
21 Construction
Add the following new subclause:
21.Z1 Addition:
Cut-off machines not intended to be operated with a liquid system are considered to be tools where a
considerable amount of dust is produced.

Add the following new figures:

Figure Z101 - Positions of transducers for various kinds of cut-off-machines

- 7 - EN 60745-2-22:2011
Dimensions in mm
Key
1 cut-off machine
2 workpiece (concrete slab)
3 hose for dust extraction
4 supporting concrete block
Figure Z102 - Test set up (side view)
Dimensions in mm
Key
1 supporting concrete block
2 workpiece (concrete slab)
3 cut-off machine
4 line of cut
Figure Z103 - Test set up (top view)

Add the following annexes.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

Addition:
Publication Year Title EN/HD Year

EN 1339 2003 Concrete paving flags - - -
Requirements and test methods
ISO 603-15 1999 Bonded abrasive products - Dimensions - - -
Part 15: Grinding wheels for cutting-off on
stationary or mobile cutting-off machines

ISO 603-16 1999 Bonded abrasive produtcs - Dimensions - - -
Part 16: Grinding wheels for cutting-off on
hand held power tools
- 9 - EN 60745-2-22:2011
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential requirements
of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
IEC 60745-2-22 ®
Edition 1.0 2011-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Hand-held motor-operated electric tools – Safety –
Part 2-22: Particular requirements for cut-off machines

Outils électroportatifs à moteur – Sécurité –
Partie 2-22: Règles particulières pour les tronçonneuses à disques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX T
ICS 25.140.20 ISBN 978-2-88912-394-0

– 2 – 60745-2-22 © IEC:2011
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 7
5 General conditions for the tests . 8
6 Void. 8
7 Classification . 8
8 Marking and instructions .
...