IEC 63241-1:2023 specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This document applies to those tools with and without a dust extraction unit where dust such as mineral dust containing silica or wood dust is expected.

  • Standard
    29 pages
    English and French language
    sale 15% off

IEC 63241-2-6:2023 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure – Particular requirements for hand-held hammers.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

  • Standard
    20 pages
    English and French language
    sale 15% off

IEC 62841-4-7:2022 clause 1 of IEC 62841-1:2014, is applicable, except as follows: Addition: This document applies to pedestrian controlled walk-behind lawn scarifiers and lawn aerators which are designed for regenerating lawns by combing out materials such as grass, thatch and moss or cutting vertically into the lawn face using  metallic tines; and/or rigid non-metallic tines  which rotate about a horizontal axis. This document does not apply to  pedestrian controlled walk-behind lawnmowers; towed/semi-mounted lawn scarifiers and lawn aerators; ride-on machines; non-powered lawn scarifiers and lawn aerators; combustion engine powered lawn scarifiers and lawn aerators; plug aerators (corers); hybrid and fuel cell powered machines and associated charging systems; and garden tractors or their attachments.

  • Standard
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62841-4-7:2022 clause 1 of IEC 62841-1:2014, is applicable, except as follows:
Addition:
This document applies to pedestrian controlled walk-behind lawn scarifiers and lawn aerators which are designed for regenerating lawns by combing out materials such as grass, thatch and moss or cutting vertically into the lawn face using
metallic tines; and/or
rigid non-metallic tines
which rotate about a horizontal axis.
This document does not apply to
pedestrian controlled walk-behind lawnmowers;
towed/semi-mounted lawn scarifiers and lawn aerators;
ride-on machines;
non-powered lawn scarifiers and lawn aerators;
combustion engine powered lawn scarifiers and lawn aerators;
plug aerators (corers);
hybrid and fuel cell powered machines and associated charging systems; and
garden tractors or their attachments.
The contents of the corrigendum of May 2023 have been included in this copy.

  • Standard
    187 pages
    English and French language
    sale 15% off

This document specifies the principal dimensions of slip joint pliers, designated as No. 206 in ISO 5742, and the test values, in order to verify their aptitude to function in conformity with ISO 5744. The general technical requirements are given in ISO 5743. The slip joint pliers illustrated in this document are examples only and are not intended to affect the manufacturer's design.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
  • Draft
    2 pages
    English language
    sale 15% off

This document specifies the general technical requirements to be met by pliers and nippers. It does not specify insulating or antistatic characteristics of handle coatings. Plastic coatings or plastic sleeves are intended for gripping comfort only. This document is only applicable to pliers for which ISO standards exist.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Draft
    5 pages
    English language
    sale 15% off

This document specifies the principal dimensions of engineer's and Lineman's pliers and the test values for the pliers in order to verify their aptitude to function in conformity with ISO 5744. General technical requirements are given in ISO 5743. The engineer's and Lineman's pliers illustrated in this document are examples only and are not intended to affect the manufacturer's design.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Draft
    6 pages
    English language
    sale 15% off

This document specifies the principal dimensions of multiple slip joint pliers. It also specifies test values for the pliers to verify their aptitude to function in conformity with ISO 5744. General technical requirements are given in ISO 5743. The multiple slip joint pliers illustrated in this document are only examples and are not intended to affect the manufacturer's design.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected.
This part of EN 50632 sets particular requirements for transportable mitre saws.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 62841 applies to hand-held hammers.
Tools covered by this document include percussion hammers and rotary hammers,
including rotary hammers with the capability to rotate only with the percussion system
disengaged (drill only mode).
This document does not apply to drills and impact drills.
NOTE 101 Drills and impact drills are covered by IEC 62841-2-1.
This document does not apply to tools that are designed exclusively for driving fasteners,
such as palm nailers.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2019-07-05: to be launched to the enquiry together with pr = 70011 (SV)
2019-07-05: Represents common mods. to EN 62841-2-6 (PR=70011)

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the dimensions and technical requirements for ratcheting wrenches used in assembly or disassembly of hexagonal and double hexagonal fasteners. NOTE The wrenches covered by this document are the ones identified in ISO 1703 under reference No.1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 and 1 1 02 19 0, 1 1 02 20 0. NOTE The wrenches according to this document are not intended for uses with impact stress of the wrench.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Draft
    11 pages
    English language
    sale 15% off

2020-01-06 JF: the Annex ZZ which had been approved by  the BT is not the most recent one -> need to submit the correct Annex ZZ to the BT. The BT document under preparation.
2019-11-05 JF: Through the BT decision D163/C100, the BT approved the revised Annex ZZ of the standard. Standard under publlication.
NEXT ACTION: CCMC ACTION BY 2019-08-30: submission of the revised Annex ZZ for the BT approval.
Compliant assessment of the Annex ZA received.
2019-05-08 JF: HAS Consultants confirmed that the request for assessment will be accepted but asked to  issue a new request by CCMC. CCMC made a new request. The indicative deadline to receive it: 2019-06-12
2019-04-19 JF: EC clarified that HAS Consutlants will carry out the assessment of the corrected Annex ZZ. NEXT ACTION: HAS CONSULTANT ASSESSMENT EXPECTED BY 2019-05-23.
2019-01-30 Assessment request rejected by HAS Consultants on the grounds that it is a second requset at this stage. CCMC asked the EC to clarify.
2019-

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62841-2-11:2015 applies to applies to reciprocating saws such as jig saws and sabre saws.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-11 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: reciprocating saw, jig saw, sabre saw, hand-held tool, transportable tool

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is applicable to driving parts of hand-operated square drive socket wrenches. NOTE The driving parts covered by this document are the ones identified in ISO 1703:2018 under reference No. 6 1 00 01 0 and 6 1 00 01 1, 6 1 00 03 0, 6 1 00 04 0, 6 1 00 05 0 and 6 1 00 05 1, 6 1 00 06 0 and 6 1 00 06 1, 6 1 00 09 0 as well as 6 1 00 10 0 and 6 1 00 10 1. It specifies: a) the overall dimensions; b) the minimum Rockwell hardness value for their driving squares; c) the method of torque testing; d) the minimum torsional strength values; e) the designation; f) the marking.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

This document applies to attachments for hand-operated square drive socket wrenches. NOTE 1 The attachments for hand-operated square drive socket wrenches covered by this standard are the ones identified in ISO 1703:2018 under reference No. 5 1 00 03 0, 5 1 00 04 0, 5 1 00 04 1 and 5 1 00 05 0. It specifies a) the overall dimensions; b) the minimum Rockwell hardness value for their driving squares; c) the method of torque testing; d) the minimum torsional strength values; e) the designation; and f) the marking. NOTE 2 For the specification of square adaptors with a hexagon or cylindrical flat drive, for power socket wrenches, see ISO 3317.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

ISO 6787:2018 specifies the dimensions of adjustable wrenches and the admissible clearance of the adjustable jaw. It also specifies test conditions to test the suitability of tool performance.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 6789-2:2017 specifies the method for the calibration of hand torque tools and describes the method of calculation of measurement uncertainties for the calibration.
ISO 6789-2:2017 specifies the minimum requirements for the calibration of the torque measurement device where the relative measurement uncertainty interval, W´md, is not already provided by a traceable calibration certificate.
ISO 6789 is applicable for the step by step (static) and continuous (quasi-static) calibration of torque measurement devices, the torque of which is defined by measuring of the elastic form change of a deformable body or a measured variable which is in proportion to the torque.
ISO 6789-2:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II).
NOTE          Hand torque tools covered by this document are the ones identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 6789-1:2017 specifies the conformance testing and marking requirements for hand torque tools used for controlled tightening of screws and nuts. It also specifies the minimum requirements for declaration of conformance for hand torque tools.
ISO 6789-1:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II).
NOTE          Hand torque tools covered by this document are those identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added.
ISO 6789-1:2017 does not specify requirements of calibration certificates for hand torque tools. These are described in ISO 6789‑2.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 10103:2018 specifies the overall length and the maximum head thickness for double-headed box wrenches, flat (Form B) and offset (Form A). NOTE The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference numbers 1 1 02 03 0 and 1 1 02 04 0. ISO 10103:2018 covers technical specifications for the test torque of these products. All other technical specifications are given in ISO 1711‑1.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

ISO 10104:2018 specifies the overall length and the maximum head thickness for double-headed box wrenches, deep offset (Form B) and modified offset (Form A). NOTE The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference numbers 1 1 02 06 0 and 1 1 02 05 0. ISO 10104:2018 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑1:2016, series A.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 10102:2018 specifies the overall length and the maximum head thickness for double-headed open-ended engineers' wrenches. NOTE The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference No. 1 1 01 02 0. ISO 10102:2018 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑1:2016, series C.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

This part of IEC 62841 applies to mixers. Mixers are not considered to be tools with a liquid
system.
This standard does not apply to drills and impact drills, even if they can be used as a mixer.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 2725-1:2017 specifies dimensions, the designation, and the marking of hand-operated square drive sockets with operating end and having a hexagonal or double hexagonal form in accordance with ISO 1174‑1. NOTE Hand-operated square drive sockets covered by this document are the ones identified in ISO 1703 under reference numbers 2 1 02 01 0. ISO 2725-1:2017 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑1.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

ISO 13778:2017 specifies requirements of single-head engineer's wrenches with nominal width across flats from 3,2 to 120. It specifies the maximum outside dimensions of heads and gives the test torque values. The "lower torque application" designation is in accordance with the smaller head dimensions. NOTE The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference Nos. 1 1 01 01 0 and 1 1 01 01 1.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

This document specifies the conformance testing and marking requirements for hand torque tools used
for controlled tightening of screws and nuts. It also specifies the minimum requirements for declaration
of conformance for hand torque tools.
This document applies to hand torque tools which are classified as indicating torque tools (Type I) and
setting torque tools (Type II).
NOTE Hand torque tools covered by this document are those identified in ISO 1703:2005 by reference
numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently
under revision. In the next edition, torque tools will be moved to an own clause, and with this change the
reference numbers will also change and additional reference numbers will be added.
This document does not specify requirements of calibration certificates for hand torque tools. These
are described in ISO 6789-2.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the method for the calibration of hand torque tools and describes the method
of calculation of measurement uncertainties for the calibration.
This document specifies the minimum requirements for the calibration of the torque measurement
device where the relative measurement uncertainty interval, W´md, is not already provided by a
traceable calibration certificate.
ISO 6789 is applicable for the step by step (static) and continuous (quasi-static) calibration of torque
measurement devices, the torque of which is defined by measuring of the elastic form change of a
deformable body or a measured variable which is in proportion to the torque.
This document applies to hand torque tools which are classified as indicating torque tools (Type I) and
setting torque tools (Type II).
NOTE Hand torque tools covered by this document are the ones identified in ISO 1703:2005 by reference
numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently
under revision. In the next edition, torque tools will be moved to an own clause, and with this change the
reference numbers will also change and additional reference numbers will be added.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 6789-2:2017 specifies the method for the calibration of hand torque tools and describes the method of calculation of measurement uncertainties for the calibration. ISO 6789-2:2017 specifies the minimum requirements for the calibration of the torque measurement device where the relative measurement uncertainty interval, W´md, is not already provided by a traceable calibration certificate. ISO 6789 is applicable for the step by step (static) and continuous (quasi-static) calibration of torque measurement devices, the torque of which is defined by measuring of the elastic form change of a deformable body or a measured variable which is in proportion to the torque. ISO 6789-2:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II). NOTE Hand torque tools covered by this document are the ones identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added.

  • Standard
    41 pages
    English language
    sale 15% off
  • Standard
    43 pages
    French language
    sale 15% off

ISO 6789-1:2017 specifies the conformance testing and marking requirements for hand torque tools used for controlled tightening of screws and nuts. It also specifies the minimum requirements for declaration of conformance for hand torque tools. ISO 6789-1:2017 applies to hand torque tools which are classified as indicating torque tools (Type I) and setting torque tools (Type II). NOTE Hand torque tools covered by this document are those identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1 and 6 1 00 12 0, 6 1 00 12 1 and 6 1 00 14 0, 6 1 00 15 0. ISO 1703 is currently under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added. ISO 6789-1:2017 does not specify requirements of calibration certificates for hand torque tools. These are described in ISO 6789‑2.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    24 pages
    French language
    sale 15% off

ISO 3318:2016 specifies the maximum outside head dimensions for open-ended wrenches, box wrenches and combination wrenches. NOTE 1 The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference nos. 1 1 01 02 0, 1 1 01 05 0, 1 1 01 06 0, 1 1 02 03 0, 1 1 02 04 0, 1 1 02 05 0, 1 1 02 06 0, 1 1 02 01 0, 1 1 02 02 0 and 1 1 02 08 0. NOTE 2 Box wrenches can also be designated as ring wrenches. ISO 3318:2016 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑1.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 1085:2016 specifies the size pairing of double-ended wrenches with unequal nominal widths across flats. NOTE The wrenches covered by this document are those identified in ISO 1703:2005 under reference nos. 1 1 01 02 0, 1 1 02 03 0, 1 1 02 04 0, 1 1 02 05 0, 1 1 02 06 0, 1 1 02 08 0.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

IEC 60745-2-23:2012 applies to die grinders and small rotary tools for mounted accessories not exceeding 55 mm in diameter and mounted sanding accessories not exceeding 80 mm in diameter such as, threaded cones or plugs that are threaded on a mandrel with an unrelieved shoulder flange, mandrel mounted wheels and rotary files with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity. This part 2 is to be used in conjunction with the latest edition of IEC 60745-1 and its amendments. It was established on the basis of the fourth edition (2006) of that standard. This standard does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory. Those tools are covered by IEC 60745-2-3. Keywords: Die grinders, rotary tools, grinding, sanding.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62841-2-11:2015 applies to applies to reciprocating saws such as jig saws and sabre saws.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
This publication is to be read in conjunction with IEC 62841-1:2014.

  • Standard
    44 pages
    English and French language
    sale 15% off

ISO 3317:2015 prescribes the technical specifications for square drive adaptor hexagon or cylindrical flat inserts for power socket wrenches. It applies to square drive adaptor with hexagon drive or with cylindrical flat end drive as defined in ISO 1173, and to driving squares for power socket wrenches as defined in ISO 1174‑2. Square drive adaptors with hexagon drive for power socket wrenches are listed under number 5 2 00 02 0 in ISO 1703.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    French language
    sale 15% off

ISO 7738:2015 specifies the overall length and the maximum head thickness of combination wrenches, offset (Form A) and offset (Form B). NOTE Combination wrenches are listed in ISO 1703, under designation 1 1 01 05 0 (Form A) and designation 1 1 01 06 0 (Form B).

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 2936:2014 specifies the dimensions, the method of test, the designation, and the marking of hexagon socket screw keys. It also specifies the minimum values of Rockwell hardness that are to be met. Its specifications apply for tightening of hexagon socket screws for property class less than or equal to 12,9 as defined in ISO 898‑1 and for tightening of socket set screws as defined in ISO 898‑5.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off

IEC 60745-2-23:2012 applies to die grinders and small rotary tools for mounted accessories not exceeding 55 mm in diameter and mounted sanding accessories not exceeding 80 mm in diameter such as, threaded cones or plugs that are threaded on a mandrel with an unrelieved shoulder flange, mandrel mounted wheels and rotary files with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity. This part 2 is to be used in conjunction with the latest edition of IEC 60745-1 and its amendments. It was established on the basis of the fourth edition (2006) of that standard. This standard does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory. Those tools are covered by IEC 60745-2-3. Keywords: Die grinders, rotary tools, grinding, sanding.
This publication is to be read in conjunction with IEC 60745-1:2006.

  • Standard
    33 pages
    English and French language
    sale 15% off

Specifies requirements, limiting dimensions and operating forces for hand crimping tools with removable and interchangeable dies, sizes A to G, Q to T, V and W, for the termination of cables to radio frequency connectors. For tool style references see 5.1 and table 1.

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 1174-1:2011 specifies the dimensions, separation force and designation of driving squares for hand socket tools.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

IEC 60745-2-5:2010 deals with the safety of hand-held motor-operated or magnetically driven electric tools, specific requirements for all types of circular saws. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c. tools. This standard does not apply to saws used with abrasive wheels. The principal changes in this edition as compared with the fourth edition are as follows:
- clause 17 introduction of endurance tests in practical use for the guards of all types of saws;
- clause 19 clarifications and editorial improvements in respect to the guarding;
- annex M editorial improvements.
This publication is to be read in conjunction with  IEC 60745-1:2006.

  • Standard
    100 pages
    English and French language
    sale 15% off

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven wrenches, nutrunners and screwdrivers used for tightening and loosening threaded fasteners. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine when operating at a specified load. The method has been tested for fastening tasks only. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to hand-held machines (see Clause 5), driven pneumatically or by other means, with impact or impulse action, of shut-off, ratchet or stall type, and of all designs - straight, pistol-grip, angle or bow handle. It covers machines with 6,3 mm to 40 mm (1/4 in to 11/2 in) male or female drive output shafts, as well as other geometries. It is not applicable to nutrunners designed to be used only in torque reaction arms.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Applies to sanders with the exception of all types of disc-type sanders, which are covered by IEC 60745-2-3. Tools covered include but are not limited to belt sanders, reciprocating sanders or polishers, orbital sanders or polishers, and random orbit sanders or polishers.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the properties of double-hex sockets for aerospace use.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the properties of the following types of double end box wrenches: double head flat, double head offset and double end modified offset.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day