EN 61029-2-11:2012

SLOVENSKI STANDARD
01-marec-2013
9DUQRVWSUHPLþQLKHOHNWULþQLKRURGLMGHO3RVHEQH]DKWHYH]DNRPELQLUDQH
NURåQHåDJH]GHORYQRPL]RLQ]D]DMHUDOQHåDJH
Safety of transportable motor-operated electric tools - Part 2-11: Particular requirements
for combined mitre and bench saws
Sicherheit transportabler motorbetriebener Elektrowerkzeuge - Teil 2-11: Besondere
Anforderungen für kombinierte Tischund Gehrungssägen
Sécurité des machines-outils électriques semi-fixes - Partie 2-11: Règles particulières
pour les scies d'établi-scies à mortaiser
Ta slovenski standard je istoveten z: EN 61029-2-11:2012
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61029-2-11
NORME EUROPÉENNE
October 2012
EUROPÄISCHE NORM
ICS 25.080.60; 25.140.20 Supersedes EN 61029-2-11:2009

English version
Safety of transportable motor-operated electric tools -
Part 2-11: Particular requirements for combined mitre and bench saws
(IEC 61029-2-11:2001, modified)

Sécurité des machines-outils Sicherheit transportabler
électriques semi-fixes - motorbetriebener Elektrowerkzeuge -
Partie 2-11: Règles particulières pour Teil 2-11: Besondere Anforderungen für
les scies d'établi-scies à mortaiser kombinierte Tisch- und Gehrungssägen
(CEI 61029-2-11:2001, modifiée) (IEC 61029-2-11:2001, modifiziert)

This European Standard was approved by CENELEC on 2012-09-03. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
-
Ref. No. EN 61029-2-11:2012 E
Contents
Foreword . 4
1 Scope . 6
2 Definitions . 6
3 General requirement . 7
4 General notes on tests . 7
5 Rating . 7
6 Classification . 7
7 Marking and information for use . 7
8 Protection against electric shock . 9
9 Starting . 9
10 Input and current . 10
11 Heating . 10
12 Leakage current . 10
13 Environmental requirements . 10
14 Protection against ingress of foreign bodies and moisture resistance . 10
15 Insulation resistance and electric strength . 11
16 Endurance . 11
17 Abnormal operation . 11
18 Stability and mechanical hazards . 11
19 Mechanical strength . 20
20 Construction. 21
21 Internal wiring . 22
22 Components . 22
23 Supply connection and external flexible cables and cords . 22
24 Terminals for external conductors . 22
25 Provision for earthing . 22
26 Screws and connections . 22
27 Creepage distances, clearances and distance through insulation . 23
28 Resistance to heat, fire and tracking . 23
29 Resistance to rusting . 23
30 Radiation . 23
Annex A (normative) Normative references . 44
Annex ZD (informative) Dust measurement . 45
Annex ZZ (informative) Coverage of Essential Requirements of Directive 2006/42/EC . 46

– 3 – EN 61029-2-11:2012
Figures
Figure Z101 – Combined mitre and bench saw (Type “A”) . 24
Figure Z102 – Combined mitre and bench saw (Type “B”) . 25
Figure Z103 – Orientation of tool and operator. 26
Figure Z104 – Saw blade areas − Combined mitre and bench saw in mitre saw position (Type “B”) . 27
Figure Z105 – Self-closing guard − Opening angle . 28
Figure Z106 – Open guard construction . 29
Figure Z107 – Guarding of saw blade relative to mitre saw table position (Type “A” machine) . 29
Figure Z108 – Dimensions of test probe . 30
Figure Z109 – Riving knife mounted guard . 30
Figure Z110 – Top guard side walls . 31
Figure Z111 – Saw blade guard − Stability test . 32
Figure Z112 – Guarding below the bench table (Type “B” machine) . 34
Figure Z113 – Width of the slot in the table . 34
Figure Z114 – Dimensions of the bench saw table . 35
Figure Z115 – Riving knife adjustment . 36
Figure Z116 – Riving knife testing − Strength of riving knife mounting . 37
Figure Z117 – Riving knife testing − Resiliency of riving knife . 38
Figure Z118 – Two position rip fence . 39
Figure Z119 – Distance between fence and saw blade in mitre saw mode . 40
Figure Z120 – Flange characteristics . 41
Figure Z121 – Examples of push stick and push block handle . 42
Figure Z122 – Saw with workpiece support in mitre saw mode . 43

Tables
Table Z101 – Noise test conditions for combined mitre and bench saws . 10
Table ZD.101 – Conditions for dust measurement . 45

Foreword
This document (EN 61029-2-11:2012) consists of the text of IEC 61029-2-11:2001 prepared by
IEC/SC 61F (transformed into IEC TC 116 "Safety of hand-held motor-operated electric tools"), together
with the common modifications prepared by CLC/TC 116 "Safety of motor-operated electric tools".
The following dates are fixed:
(dop) 2013-09-03
• latest date by which the document has to be
implemented at national level
by publication of an identical
national standard or by endorsement
(dow) 2015-09-03
• latest date by which the national standards
conflicting with the
document have to be withdrawn
This document supersedes EN 61029-2-11:2009.
EN 61029-2-11:2009:
– introduction of 'linked action'
– rewording of some clauses;
– improvement and clarification of Clause 18.
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all
such patent rights.
This European Standard is divided into two parts:
Part 1 General requirements, which are common to most transportable motor, operated tools (for the
purpose of this European Standard referred to simply as tools) which could come within the scope
of this European Standard.
Part 2 Requirements for particular types of tool which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
Compliance with the relevant clauses of Part 1 together with a relevant Part 2 of this European Standard
provides one means of conforming to the specified essential requirements of the Directive.
This European Standard follows the overall requirements of EN ISO 12100.
For noise and vibration, this European Standard covers the requirements for their measurement, the
provisions of information arising from these measurements and the provision of information about the
Personal Protective Equipment required. Specific requirements for the reduction of the risk arising from
noise and vibration through the design of the tool are not given as this reflects the current state of art.
Other requirements arising from other EU Directives can be applicable to the products
Warning:
falling within the scope of this European Standard.

– 5 – EN 61029-2-11:2012
CEN has prepared standards for industrial machines, which may extend to transportable machines.
Although CEN and CENELEC have where appropriate used common solutions to provide uniform levels
of protection, persons using this European Standard should check the scope of both this and CEN
standards to ensure that a correct standard is used.
This Part 2-11 is to be used in conjunction with EN 61029-1:2009. This Part 2-11 supplements or modifies
the corresponding clauses of EN 61029-1, so as to convert it into the European Standard: “Particular
requirements for combined mitre and bench saws”.
Where a particular subclause of Part 1 is not mentioned in this Part 2-11, that subclause applies as far as
reasonable. Where this Part 2-11 states "addition" "modification" or "replacement", the relevant text of
Part 1 is to be adapted accordingly.
Clauses, subclauses, notes, tables and figures which are additional to those in Part 1 are numbered
starting from 101.
Clauses, subclauses, notes, tables and figures which are additional to tho
...