SIST EN 10021:2007

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Allgemeine technische Lieferbedingungen für StahlerzeugnisseConditions générales techniques de livraison des produits en acierGeneral technical delivery conditions for steel products77.140.01Železni in jekleni izdelki na splošnoIron and steel products in generalICS:Ta slovenski standard je istoveten z:EN 10021:2006SIST EN 10021:2007en01-marec-2007SIST EN 10021:2007SLOVENSKI
STANDARDSIST EN 10021:19961DGRPHãþD



SIST EN 10021:2007



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10021December 2006ICS 77.140.01Supersedes EN 10021:1993
English VersionGeneral technical delivery conditions for steel productsConditions générales techniques de livraison des produitsen acierAllgemeine technische Lieferbedingungen fürStahlerzeugnisseThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10021:2006: ESIST EN 10021:2007



EN 10021:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Information to be supplied by the purchaser.6 5 Manufacturing process.6 6 Supply by an intermediary.6 7 Requirements.7 7.1 General.7 7.2 Chemical composition.7 7.3 Mechanical properties.7 7.4 Surface and internal quality.7 7.4.1 General.7 7.4.2 Detection of discontinuities.7 7.4.3 Removal of discontinuities.7 7.4.4 Repairs by welding.8 8 Inspection.8 8.1 Type of inspection documents and type of inspection.8 8.2 Non-specific inspection.8 8.3 Specific inspection.8 8.3.1 General.8 8.3.2 Testing frequency.9 8.3.3 Sampling conditions and test pieces.9 8.3.4 Test procedures.10 8.4 Invalidation of test results.11 8.5 Rounding of results of mechanical and chemical tests.11 9 Sorting and reprocessing.11 10 Marking.12 11 Disputes.12 Bibliography.17
SIST EN 10021:2007



EN 10021:2006 (E) 3 Foreword This document (EN 10021:2006) has been prepared by Technical Committee ECISS/TC 9 “Technical conditions of delivery and quality control”, the secretariat of which is held by IBN/BIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 10021:2007



EN 10021:2006 (E) 4 1 Scope This European Standard specifies the general technical delivery conditions for all steel products covered by EN 10079 with the exception of steel castings and powder metallurgical products. Where the delivery requirements agreed for the order or specified in the appropriate product specification differ from the general technical delivery conditions defined in this European Standard, then the requirements agreed for the order or specified in the appropriate product specification apply. NOTE Inspection documents are covered by EN 10168 and EN 10204. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. CR 10261, ECISS Information Circular 11 — Iron and steel — Review of available methods of chemical analysis EN 10020:2000, Definition and classification of grades of steel EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:1992, Definition of steel products EN 10204:2004, Metallic products — Types of inspection documents EN ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) ISO 31-0:1992, Quantities and units — Part 0: General principles 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10052:1993,
EN 10079:1992, EN 10204:2004 and the following apply. 3.1 cast (heat) analysis chemical analysis representative of the cast (heat) determined by the steelmaker at his discretion in a manner of his choice 3.2 inspection conformity evaluation by observation and judgment accompanied as appropriate by measurement, testing or gauging 3.3 inspection representative(s) one or more individual(s) who is/are either: a) the inspector(s) designated in any official regulation; b) the manufacturer’s authorized inspection representative(s), independent from the manufacturing department; c) the purchaser’s authorized inspection representative(s) SIST EN 10021:2007



EN 10021:2006 (E) 5 NOTE 1 The inspection representatives mentioned in a) and c) are referred to in the text as external inspection representatives. NOTE 2 The inspection representatives validate the inspection and test results. Inspection and testing can also be carried out by the manufacturing department. 3.4 non-specific inspection inspection carried out by the manufacturer in accordance with his own procedures to assess whether products defined by the same product specification and made by the same manufacturing process are in compliance with the requirements of the order or not NOTE The products inspected may not necessarily be the products actually supplied. 3.5 product analysis chemical analysis carried out on a sample of the product 3.6 rough specimen part of the sample having undergone forming and/or machining, followed by heat treatment where appropriate, for the purpose of producing test pieces (see Figure 1) 3.7 sample sufficient quantity of material taken from the sample product for the purposes of producing one or more test pieces (see Figure 1) NOTE In certain cases, the sample can be the sample product itself or the rough specimen. 3.8 sample product item (a sheet, for example) selected from a test unit for the purpose of obtaining test pieces (see Figure 1) NOTE In certain cases the sample product can be the sample itself. 3.9 sequential testing group or series of tests from which the average and individual results are used to demonstrate that the requirements of the order and/or product specification have been satisfied 3.10 specific inspection inspection carried out, before delivery, according to the product specification on the products to be supplied or on test units of which the products supplied are part, in order to verify that these products are in compliance with the requirements of the order 3.11 testing determination of one or more characteristics according to a procedure 3.12 test piece part of the sample, with specified dimensions, machined or un-machined, brought to a required condition for submission to a given test (see Figure 1) NOTE In certain cases, the test piece can be the sample itself or the rough specimen. SIST EN 10021:2007



EN 10021:2006 (E) 6 3.13 test unit number of pieces or mass of products to be accepted or rejected together, on the basis of the tests to be carried out on sample products in accordance with the requirements of the product specification or order (see Figure 1) 4 Information to be supplied by the purchaser 4.1 The purchaser shall select the steel grade, the shape of the product and the dimensions, taking the intended processing and use into account. He may take the manufacturer’s advice in making his choice. The order shall provide all the information necessary for describing the required product and its characteristics and details concerning delivery, e.g.: a) mass, length, area, number of pieces; b) the product form (it may be a drawing number for example); c) the nominal/specified dimensions; d) the tolerances on the characteristics in a), b) and c); e) the steel designation; f) the delivery conditions (type of heat treatment, surface treatment etc.); g) the specific requirements for surface and/or internal quality (see 7.4); h) the type of inspection document (see EN 10204) if required; i) the inspection requirements when not specified in the product specification (see Clause 8); j) the requirements for marking, packing and loading; k) any optional (supplementary) requirements provided for by the specification to apply. 4.2 The information in 4.1 shall be specified either by reference to one or more standards or, in the absence of a standard, by stipulation of the required characteristics and conditions. If, in an order, reference is made to a given standard without specifying its edition date, this reference shall be interpreted as being the latest edition at the date of the order acknowledgment. 5 Manufacturing process The manufacturing process shall be left to the discretion of the manufacturer unless otherwise agreed at the time of enquiry and order or otherwise specified in the product specification. NOTE The manufacturing process covers all operations up to the delivery of the product. 6 Supply by an intermediary When a product is supplied by an intermediary, he shall submit to the purchaser, without any changes to it, the manufacturer’s documentation. This documentation from the manufacturer shall be accompanied by suitable means of identification of the product, in order to ensure the traceability between the product and the documentation (see Clause 10). SIST EN 10021:2007



EN 10021:2006 (E) 7 If the intermediary has changed the dimensions of the product, he shall supply an additional document of compliance for these particular new conditions. This also applies to all special requirements given in the order and not defined in the manufacturer’s documentation. NOTE Any organization which during processing changes the metallurgical state of the product is considered as a product or material manufacturer. 7 Requirements 7.1 General The products shall comply with the requirements of the order. Consequently, the manufacturer shall carry out appropriate process control and inspection to ensure that the delivery complies with the requirements of the order, irrespective of the type of inspection document required (see Clause 8). NOTE Examples fo
...