SIST EN IEC 80000-6:2023

SLOVENSKI STANDARD
01-februar-2023
Nadomešča:
SIST EN 80000-6:2008
SIST IEC 80000-6:2014
Veličine in enote - 6. del: Elektromagnetizem (IEC 80000-6:2022)
Quantities and units - Part 6: Electromagnetism (IEC 80000-6:2022)
Größen und Einheiten - Teil 6: Elektromagnetismus (IEC 80000-6:2022)
Grandeurs et unités - Partie 6: Electromagnétisme (IEC 80000-6:2022)
Ta slovenski standard je istoveten z: EN IEC 80000-6:2022
ICS:
01.060 Veličine in enote Quantities and units
17.220.01 Elektrika. Magnetizem. Electricity. Magnetism.
Splošni vidiki General aspects
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 80000-6

NORME EUROPÉENNE
EUROPÄISCHE NORM December 2022
ICS 01.040.29; 17.220.01 Supersedes EN 80000-6:2008
English Version
Quantities and units - Part 6: Electromagnetism
(IEC 80000-6:2022)
Grandeurs et unités - Partie 6: Electromagnétisme Größen und Einheiten - Teil 6: Elektromagnetismus
(IEC 80000-6:2022) (IEC 80000-6:2022)
This European Standard was approved by CENELEC on 2022-12-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 80000-6:2022 E

European foreword
The text of document 25/732/FDIS, future edition 2 of IEC 80000-6, prepared by IEC/TC 25
"Quantities and units" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC
as EN IEC 80000-6:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-09-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-12-21
document have to be withdrawn
This document supersedes EN 80000-6:2008 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 80000-6:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60027-1 NOTE Harmonized as EN 60027-1
ISO 80000-2 NOTE Harmonized as EN ISO 80000-2
ISO 80000-3 NOTE Harmonized as EN ISO 80000-3
ISO 80000-4 NOTE Harmonized as EN ISO 80000-4

IEC 80000-6
Edition 2.0 2022-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Quantities and units –
Part 6: Electromagnetism
Grandeurs et unités –
Partie 6: Électromagnétisme
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 01.040.29; 17.220.01 ISBN 978-2-8322-5706-7

– 2 – IEC 80000-6:2022 © IEC 2022
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
0.1 Tables of quantities. 5
0.2 Units . 5
0.2.1 General . 5
0.2.2 Remark on units for quantities of dimension one, or dimensionless
quantities . 5
0.3 Numerical statements in this document . 6
0.4 Special remarks . 6
0.4.1 General . 6
0.4.2 System of quantities . 6
0.4.3 Sinusoidal quantities. 7
0.4.4 Root-mean-square value, RMS value . 7
1 Scope . 8
2 Normative references . 8
3 Names, symbols, definitions and units of quantities . 8
Annex A (informative) Units in the CGS system with special names . 27
Alphabetical index . 28
Bibliography . 34

Table 1 – Quantities and units in electromagnetism . 9
Table A.1 – Deprecated units with special names taken from the CGS system . 27

IEC 80000-6:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
QUANTITIES AND UNITS –
Part 6: Electromagnetism
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 80000-6 has been prepared by IEC technical committee 25: Quantities and units, and their
letter symbols in close cooperation with ISO/TC 12, Quantities and units. It is an International
Standard.
This second edition of IEC 80000-6 cancels and replaces the first edition published in 2008.
This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) With the new definitions in SI, some previously exact values for quantities now must be
determined experimentally while other quantities are given as exact values;
b) Item 6-2.2, elementary charge added;
c) Item 6-11.4, induced voltage, added;
d) Index of entries added;
e) Editorial alignment to other parts of the IEC and ISO 80000 series.

– 4 – IEC 80000-6:2022 © IEC 2022
The text of this International Standard is based on the following documents:
Draft Report on voting
25/732/FDIS 25/740/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
IEC 80000 consists of the following parts, under the general title Quantities and units:
1) Part 6: Electromagnetism
2) Part 13: Information science and technology
3) Part 15: Logarithmic and related quantities, and their units
4) Part 16: Printing and writing rules
5) Part 17: Time dependency
The following parts are published by ISO:
1) Part 1: General
2) Part 2: Mathematical signs and symbols to be used in the natural sciences and technology
3) Part 3: Space and time
4) Part 4: Mechanics
5) Part 5: Thermodynamics
6) Part 7: Light
7) Part 8: Acoustics
8) Part 9: Physical chemistry and molecular physics
9) Part 10: Atomic and nuclear physics
10) Part 11: Characteristic numbers
11) Part 12: Condensed matter physics
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 80000-6:2022 © IEC 2022 – 5 –
INTRODUCTION
0.1 Tables of quantities
The names in English of the most important quantities within the field of this document are given
together with their symbols and, in most cases, their definitions. The definitions are given for
identification of the quantities in the International System of Quantities (ISQ), listed in Table 1;
they are not intended to be complete.
The scalar, vectorial or tensorial character of quantities is pointed out, especially when this is
needed for the definitions.
In most cases, only one name and only one symbol for the quantity are given; where two or
more names or two or more symbols are given for one quantity and no special distinction is
made, they are on an equal footing. When two types of italic letters exist (for example as with
ϑ and θ; φ and φ; a and a; g and g) only one of these is given. This does not mean that the other
is not equally acceptable. It is recommended that such variants should not be given different
meanings. A symbol within parent
...