EN ISO 12217-1:2013
(Main)Small craft - Stability and buoyancy assessment and categorization - Part 1: Non-sailing boats of hull length greater than or equal to 6 m (ISO 12217-1:2013)
Small craft - Stability and buoyancy assessment and categorization - Part 1: Non-sailing boats of hull length greater than or equal to 6 m (ISO 12217-1:2013)
ISO 12217-1:2013 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats vulnerable to swamping are also encompassed.
The evaluation of stability and buoyancy properties using ISO 12217-1:2013 will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum total load.
ISO 12217-1:2013 is principally applicable to boats propelled by human or mechanical power of 6 m up to 24 m hull length. However, it can also be applied to boats of under 6 m if they do not attain the desired design category specified in ISO 12217-3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, ISO 12217-1:2013 includes assessment of vulnerability to inversion, definition of viable means of escape and requirements for inverted flotation.
ISO 12217-1:2013 excludes:
inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217;
personal watercraft covered by ISO 13590 and other similar powered craft;
gondolas and pedalos;
sailing surfboards;
surfboards, including powered surfboards;
hydrofoils and hovercraft when not operating in the displacement mode (displacement mode means that the boat is only supported by hydrostatic forces); and
submersibles.
It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.
Kleine Wasserfahrzeuge - Stabilitäts- und Auftriebsbewertung und Kategorisierung - Teil 1: Nicht-Segelboote ab 6 m Rumpflänge (ISO 12217-1:2013)
Dieser Teil von ISO 12217 legt Verfahren für die Beurteilung von Stabilität und Auftrieb des intakten (d. h. unbeschädigten) Bootes fest. Ebenfalls sind darin die Auftriebseigenschaften solcher Boote erfasst, die durch Vollschlagen gefährdet sind.
Die Beurteilung der Stabilitäts- und Auftriebseigenschaften nach diesem Teil von ISO 12217 erlaubt es, dem Boot eine Entwurfskategorie (A, B, C, oder D) zuzuordnen, die seiner Auslegung und seiner maximalen Beladung entspricht.
Dieser Teil der ISO 12217 ist grundsätzlich auf Boote in einem Bereich von 6 m bis 24 m Rumpflänge, die durch Muskelkraft oder Motor angetrieben werden, anwendbar. Er kann jedoch auch auf Boote von weniger als 6 m Rumpflänge angewendet werden, wenn diese bei Anwendung von ISO 12217-3 nicht die gewünschte Entwurfskategorie erreichen, jedoch voll gedeckt sind und schnell-lenzende Rezesse entsprechend ISO 11812 besitzen.
In Bezug auf bewohnbare Mehrrümpfer beinhaltet dieser Teil von ISO 12217 eine Bewertung der Gefährdung durch Kenterung, die Bestimmung brauchbarer Fluchtmöglichkeiten und Anforderungen an die Schwimm-fähigkeit im gekenterten Zustand.
Ausgeschlossen von der Anwendung dieses Teils von ISO 12217 sind:
Schlauchboote und Schlauchboote mit festem Rumpf (RIB) nach ISO 6185 mit Ausnahme der Verweisungen, die sich in jener Norm auf bestimmte Abschnitte in ISO 12217 beziehen;
- Wassermotorräder nach ISO 13590 und andere, ähnlich angetriebene Wasserfahrzeuge;
- Gondeln und Tretboote
- Segel-Surfbretter
- Surfbretter
- Tragflügelboote und Luftkissenfahrzeuge, sofern sie nicht im Verdrängermodus betrieben werden;
- Tauchfahrzeuge.
ANMERKUNG Verdrängermodus bedeutet, dass das Boot nur durch hydrostatische Kräfte getragen wird.
Er enthält keine Angaben oder Beurteilungen zu den die Stabilität betreffenden Auswirkungen von Schleppen, Fischen, Baggern oder Kranarbeiten; diese müssen, falls erforderlich, gesondert berücksichtigt werden.
Petits navires - Évaluation et catégorisation de la stabilité et de la flottabilité - Partie 1: Bateaux à propulsion non vélique d'une longueur de coque supérieure ou égale à 6 m (ISO 12217-1:2013)
L'ISO 12217-1:2013 spécifie les méthodes d'évaluation de la stabilité et de la flottabilité des bateaux à l'état intact (c'est-à-dire non endommagés). Les caractéristiques de flottabilité des bateaux susceptibles d'envahissement sont également comprises.
L'évaluation des propriétés de stabilité et de flottabilité faite en utilisant l'ISO 12217-1:2013 permettra d'attribuer à un bateau une catégorie de conception (A, B, C ou D) appropriée à sa conception et à sa charge maximale.
L'ISO 12217-1:2013 est principalement applicable aux bateaux propulsés par l'énergie humaine ou une énergie mécanique, d'une longueur de coque de 6 m à 24 m compris. Elle peut, cependant, être également appliquée aux bateaux de moins de 6 m, s'ils n'atteignent pas la catégorie de conception désirée en appliquant l'ISO 12217-3, et s'ils sont pontés et munis de cavités rapidement autovideuses conformes à l'ISO 11812.
Pour ce qui concerne les multicoques habitables, l'ISO 12217-1:2013 comprend l'évaluation de la vulnérabilité à l'inversion, la définition d'un moyen d'échappée viable et les exigences de flottabilité à l'état inversé.
L'ISO 12217-1:2013 exclut:
les bateaux pneumatiques et semi-rigides couverts par l'ISO 6185, excepté lorsque l'ISO 6185 fait référence à des paragraphes spécifiques de l'ISO 12217;
les véhicules nautiques à moteur (motos aquatiques), couverts par l'ISO 13590 et engins à moteur similaires;
les gondoles et pédalos;
les planches à voiles;
les planches de surf, y compris les planches motorisées;
les hydrofoils et les bateaux stabilisés par des plans porteurs lorsqu'ils ne sont pas en mode à déplacement; et
les submersibles.
Elle n'inclut ni n'évalue les effets sur la stabilité provenant du remorquage, de la pêche, du dragage ou d'opérations de levage, qui doivent être, si nécessaire, considérés séparément.
Mala plovila - Stabilnost in ocena vzgona ter kategorizacija - 1. del: Čolni razen jadrnic s trupom, večjim ali enakim 6 m (ISO 12217-1:2013)
Ta del standarda ISO 12217 določa metode za oceno stabilnosti in vzgona brezhibnih (nepoškodovanih) čolnov. Zajete so tudi značilnosti plovnosti čolnov, ki so izpostavljeni zalivanju. Ocena značilnosti stabilnosti in vzgona z uporabo tega dela standarda ISO 12217 bo omogočila, da bo čoln vključen v konstrukcijsko kategorijo (A, B, C ali D), ki je ustrezna glede na konstrukcijo in največjo skupno obremenitev. Ta del standarda ISO 12217 se uporablja predvsem za čolne, ki jih poganja človek ali stroj, z dolžino trupa od 6 m do 24 m. Uporablja se lahko tudi za čolne, krajše od 6 m, če niso razvrščeni v želeno konstrukcijsko kategorijo, določeno v standardu ISO 12217-3, ter imajo krov in žlebove za hitro odvodnjavanje, ki so v skladu s standardom ISO 11812. V povezavi z večtrupnimi bivalnimi plovili ta del standarda ISO 12217 vključuje oceno izpostavljenosti prevrnitvi, navedbo ustreznih možnosti umika in zahteve za plovnost v prevrnjenem stanju. Ta del standarda ISO 12217 izključuje:
– napihljive čolne in napihljive čolne, ki imajo v spodnjem delu trupa togo enoto, ki jih obravnava standard ISO 6185, razen pri sklicih iz standarda ISO 6185 na določene točke standarda ISO 12217;
– osebna plovila, ki jih obravnava standard ISO 13590, in druga podobna plovila na pogon;
– gondole in čolne na pedala;
– jadralne deske;
– deske, vključno z deskami na motorni pogon;
– hidrogliserje in plovila na zračno blazino, kadar ne delujejo v načinu izpodriva; ter
— plovila, ki lahko plujejo pod vodno gladino.
OPOMBA: Pri načinu izpodriva na čoln delujejo le hidrostatične sile. Ne vključuje ali ne vrednoti vpliva na stabilnost pri vlečenju, ribolovu, črpanju ali dvigovanju, pri katerih je treba ustreznost stabilnosti obravnavati posamezno.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2013
1DGRPHãþD
SIST EN ISO 12217-1:2002
SIST EN ISO 12217-1:2002/A1:2009
0DODSORYLOD6WDELOQRVWLQRFHQDY]JRQDWHUNDWHJRUL]DFLMDGHO ýROQLUD]HQ
MDGUQLFVWUXSRPYHþMLPDOLHQDNLPP ,62
Small craft - Stability and buoyancy assessment and categorization - Part 1: Non-sailing
boats of hull length greater than or equal to 6 m (ISO 12217-1:2013)
Kleine Wasserfahrzeuge - Stabilitäts- und Auftriebsbewertung und Kategorisierung - Teil
1: Nicht-Segelboote ab 6 m Rumpflänge (ISO 12217-1:2013)
Petits navires - Évaluation et catégorisation de la stabilité et de la flottabilité - Partie 1:
Bateaux à propulsion non vélique d'une longueur de coque supérieure ou égale à 6 m
(ISO 12217-1:2013)
Ta slovenski standard je istoveten z: EN ISO 12217-1:2013
ICS:
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 12217-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 47.080 Supersedes EN ISO 12217-1:2002
English Version
Small craft - Stability and buoyancy assessment and
categorization - Part 1: Non-sailing boats of hull length greater
than or equal to 6 m (ISO 12217-1:2013)
Petits navires - Évaluation et catégorisation de la stabilité et Kleine Wasserfahrzeuge - Stabilitäts- und
de la flottabilité - Partie 1: Bateaux à propulsion non vélique Auftriebsbewertung und Kategorisierung - Teil 1: Nicht-
d'une longueur de coque supérieure ou égale à 6 m (ISO Segelboote ab 6 m Rumpflänge (ISO 12217-1:2013)
12217-1:2013)
This European Standard was approved by CEN on 21 December 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12217-1:2013: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC . 4
Foreword
This document (EN ISO 12217-1:2013) has been prepared by Technical Committee ISO/TC 188 "Small craft".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12217-1:2002.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12217-1:2013 has been approved by CEN as EN ISO 12217-1:2013 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission to
provide one means of conforming to Essential Requirements of the New Approach Directive 94/25/EC as
amended by Directive 2003/44/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one member state, compliance with the normative clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and EU Directives
Corresponding
Clauses/sub-clauses of this annexes/paragraphs of
Comments
European Standard Directive 94/25/EC as amended
by 2003/44/EC
Annex IA, Clause 3.2, Stability
and Freeboard; Clause 3.3,
Buoyancy and flotation; Clause
5, 6, Annexes A, B, C, D, E 3.5, Flooding; Clause 3.6,
Maximum recommended load;
and Clause 3.8, Escape in the
event of inversion.
Design categories A, B, C and D
defined in the standard are
considered to equate to design
7 Annex IA1 Design categories
categories A, B, C and D of the
Directive 94/25/EC as amended
by 2003/44/EC.
Annex IA2, Clause 3.3, Buoyancy
6.8, Annexes F, G
and flotation.
Annex IA2, Clause 2.5, Owner’s
Annex H
manual
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling
within scope of this standard.
INTERNATIONAL ISO
STANDARD 12217-1
Second edition
2013-03-01
Small craft — Stability and buoyancy
assessment and categorization —
Part 1:
Non-sailing boats of hull length greater
than or equal to 6 m
Petits navires — Évaluation et catégorisation de la stabilité et de la
flottabilité —
Partie 1: Bateaux à propulsion non vélique d’une longueur de coque
supérieure ou égale à 6 m
Reference number
ISO 12217-1:2013(E)
©
ISO 2013
ISO 12217-1:2013(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 12217-1:2013(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 Primary . 2
3.2 Downflooding . 4
3.3 Dimensions, areas and angles . 5
3.4 Condition, mass and volume . 7
3.5 Other terms and definitions . 9
4 Symbols . 11
5 Procedure .13
5.1 Maximum load .13
5.2 Sailing or non-sailing .13
5.3 Tests and calculations to be applied .13
5.4 Variation in input parameters .13
6 Tests, calculations and requirements .14
6.1 Downflooding .14
6.2 Offset-load test .19
6.3 Resistance to waves and wind .20
6.4 Heel due to wind action .22
6.5 Recess size .23
6.6 Habitable multihull boats .26
6.7 Motor sailers .26
6.8 Flotation requirements .27
6.9 Detection and removal of water .27
7 Application .27
7.1 Deciding the design category .27
7.2 Meaning of the design categories .27
Annex A (normative) Full method for required downflooding height.29
Annex B (normative) Method for offset-load test .32
Annex C (normative) Methods for calculating downflooding angle .40
Annex D (normative) Method for measuring freeboard margin .42
Annex E (normative) Determining the curve of righting moments .44
Annex F (normative) Method for level flotation test .47
Annex G (normative) Flotation material and elements .52
Annex H (normative) Information for owner’s manual .54
Annex I (informative) Summary of requirements .56
Annex J (informative) Worksheets .57
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.