This document specifies the requirements for the design, construction and installation of the following
types of DC and AC electrical systems, installed on small craft either individually or in combination:
a) extra-low-voltage direct current (DC) electrical systems that operate at nominal potentials of
50 V DC or less;
b) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding
AC 250 V.
This document does not cover the following:
— electrical propulsion systems of direct current less than 1 500 V DC, single-phase alternating
current up to 1 000 V AC, and three-phase alternating current up to 1 000 V AC, which are addressed
by ISO 16315;
— any conductor that is part of an outboard engine assembly and that does not extend beyond the
outboard engine manufacturers supplied cowling;
— three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are
addressed by IEC 60092-507.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines the dimensions, design local pressures, mechanical properties and design
stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line
length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or
weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217.
NOTE 1 The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it
can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO
conventions.
The main core of this document determines the local design pressures and stresses for monohulls and
details the possible scantlings methods derived from these pressures and stresses, both for monohulls
and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of
Annexes.
This document is applicable to small craft, in intact condition, of the two following types:
— recreational craft, including recreational charter vessels;
— small commercial craft and workboats, see Clause 12 and Annex J.
It is not applicable to racing craft designed only for professional racing.
NOTE 2 Local pressures and stresses for multihulls are given in ISO 12215-7.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights,
and doors.
For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for
rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments.
This document covers small craft built from the following materials:
— fibre-reinforced plastics, either in single skin or sandwich construction;
— aluminium or steel alloys;
— glued wood or plywood (single skin or sandwich), excluding traditional wood construction;
— non-reinforced plastics for craft with a hull length less than 6 m (see Annex D).
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses
in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1 kPa), stresses and elastic
modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a,
b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines the dimensions, design local pressures, mechanical properties and design stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217.
NOTE 1 The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
The main core of this document determines the local design pressures and stresses for monohulls and details the possible scantlings methods derived from these pressures and stresses, both for monohulls and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of Annexes.
This document is applicable to small craft, in intact condition, of the two following types:
— recreational craft, including recreational charter vessels;
— small commercial craft and workboats, see Clause 12 and Annex J.
It is not applicable to racing craft designed only for professional racing.
NOTE 2 Local pressures and stresses for multihulls are given in ISO 12215-7.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights, and doors.
For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments.
This document covers small craft built from the following materials:
— fibre-reinforced plastics, either in single skin or sandwich construction;
— aluminium or steel alloys;
— glued wood or plywood (single skin or sandwich), excluding traditional wood construction;
— non-reinforced plastics for craft with a hull length less than 6 m (see Annex D).
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1 kPa), stresses and elastic modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a, b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document establishes a coding system to achieve identification of any small craft in terms of:
— identification code of the country of the manufacturer of the craft;
— identification code of the manufacturer;
— serial number;
— month and year of manufacture;
— model year.
It applies to small craft of all types and materials, of hull length, LH, up to 24 m.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 14895:2016 specifies the design, construction and installation of permanently installed galley stoves and heating appliances using fuels which are liquid at atmospheric pressure on small craft up to 24 m length of hull (LH according to ISO 8666). It includes open flame galley stoves, ceramic hobs, blown air heaters and water heating appliances.
Cooking and heating appliances solely designed or intended as portable self-contained camping stoves or heaters are not covered. Other permanently installed cooking and heating appliances (such as solid-fuelled and liquid-fuelled natural draft stoves) are outside the scope of this International Standard and therefore covered by ISO 9094.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 11592 specifies the requirements for determination of the maximum propulsion power
rating and manoeuvring speed for engine-driven small craft with a length of hull (LH) of less than 8 m
(Lh according to ISO 8666).
This part of ISO 11592 is not applicable to the following:
— personal water craft as defined by ISO 13590;[6]
— canoes and kayaks;
— inflatable boats, as defined by ISO 6185-1, ISO 6185-2, ISO 6185-3, and ISO 6185-4, except that
ISO 6185-3 requires rigid inflatable boats (RIBS) capable of a maximum speed of 30 kn or more to
be tested in accordance to this part of ISO 11592;
— racing boats: craft designed and constructed solely for competitive racing.
This part of ISO 11592 does not specify craft constructional strength requirements related to maximum
rated power and does not guarantee security from instability under all conditions of seaway, wind,
wakes and waves.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16315:2016 addresses the design and installation of alternating current (AC) and direct current (DC) electrical systems used for the purpose of electrical propulsion and/or electrical hybrid (system with both a rechargeable battery and a fuelled power source) propulsion.
ISO 16315:2016 applies to electrical propulsion systems operated in the following ranges either individually or in combination: direct current of less than 1 500 V DC; single-phase alternating current up to AC 1 000 V; three-phase alternating current up to AC 1 000 V.
ISO 16315:2016 applies to electrical propulsion systems installed in small craft up to 24 m length of the hull (LH according to ISO 8666).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 11592-1:2016 specifies the requirements for determination of the maximum propulsion power rating and manoeuvring speed for engine-driven small craft with a length of hull (LH) of less than 8 m (Lh according to ISO 8666).
It is not applicable to the following:
personal water craft as defined by ISO 13590;[6]
canoes and kayaks;
inflatable boats, as defined by ISO 6185-1, ISO 6185-2, ISO 6185-3, and ISO 6185-4, except that ISO 6185‑3 requires rigid inflatable boats (RIBS) capable of a maximum speed of 30 kn or more to be tested in accordance to this part of ISO 11592;
racing boats: craft designed and constructed solely for competitive racing.
ISO 11592-1:2016 does not specify craft constructional strength requirements related to maximum rated power and does not guarantee security from instability under all conditions of seaway, wind, wakes and waves.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 18854:2015 specifies the measurement and evaluation methods for gaseous and particulate exhaust emissions from reciprocating internal combustion (RIC) engines under steady-state conditions on a test bed, necessary for determining one weighted value for each exhaust gas pollutant. Various combinations of engine load and speed reflect different engine applications.
It is applicable to RIC marine engines intended to be installed in small craft up to 24 m length of hull.

  • Standard
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2021-04-14 - Lack of compliance at FV stage - Publication on hold
DOW=DAV + 12 months

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for the design, construction and installation of the following
types of DC and AC electrical systems, installed on small craft either individually or in combination:
a) extra-low-voltage direct current (DC) electrical systems that operate at nominal potentials of
50 V DC or less;
b) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding
AC 250 V.
This document does not cover the following:
— electrical propulsion systems of direct current less than 1 500 V DC, single-phase alternating
current up to 1 000 V AC, and three-phase alternating current up to 1 000 V AC, which are addressed
by ISO 16315;
— any conductor that is part of an outboard engine assembly and that does not extend beyond the
outboard engine manufacturers supplied cowling;
— three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are
addressed by IEC 60092-507.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2021-04-14 - Lack of compliance at FV stage - Publication on hold
DOW=DAV + 12 months

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies technical requirements and test methods for windows, portlights, hatches, deadlights and doors on small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. It takes into account the type of craft, its design category, and the location of the appliance.
The appliances considered in this document are only those that are critical for the craft's watertightness.
Openings and non-opening devices fitted below area I (see 3.5.2) are excluded from the scope of this document.

  • Draft
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies watertightness, draining time and sill heights requirements for watertight and quick-draining recesses and cockpits in small craft of up to 24 m load line length (see Reference [1]).
Recesses located in elevated parts of the craft are covered by this document.
This document does not specify requirements for the size, the shape and the location of recesses or cockpits. It only considers draining by gravity, and not by pumping or other methods.
It only considers normal operation of the craft, but unattended craft recess issues are out of scope.
This document does not guarantee that the water contained in a watertight or quick-draining recess or cockpit will not affect the stability and buoyancy of the craft, which are covered by ISO 12217 (all parts):2015.

  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies technical requirements and test methods for windows, portlights, hatches, deadlights and doors on small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. It takes into account the type of craft, its design category, and the location of the appliance.
The appliances considered in this document are only those that are critical for the craft's watertightness.
Openings and non-opening devices fitted below area I (see 3.5.2) are excluded from the scope of this document.

  • Draft
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies watertightness, draining time and sill heights requirements for watertight and quick-draining recesses and cockpits in small craft of up to 24 m load line length (see Reference [1]).
Recesses located in elevated parts of the craft are covered by this document.
This document does not specify requirements for the size, the shape and the location of recesses or cockpits. It only considers draining by gravity, and not by pumping or other methods.
It only considers normal operation of the craft, but unattended craft recess issues are out of scope.
This document does not guarantee that the water contained in a watertight or quick-draining recess or cockpit will not affect the stability and buoyancy of the craft, which are covered by ISO 12217 (all parts):2015.

  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2015-07-27: WI deleted due to cancellation of equivalent ISO project.

  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for the field of vision from the steering position, forward (horizontally and vertically) and astern, for small craft up to 24 m length of hull (LH) in accordance with ISO 8666.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 8666:2016 establishes definitions of main dimensions and related data and of mass specifications and loading conditions. It applies to small craft having a length of the hull (LH) of up to 24 m.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 12217-1:2015 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this part of ISO 12217 will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum total load.
ISO 12217-1:2015 is principally applicable to boats propelled by human or mechanical power of 6 m up to 24 m hull length. However, it can also be applied to boats of under 6 m if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, ISO 12217-1:2015 includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
ISO 12217-1:2015 excludes:
inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217;
personal watercraft covered by ISO 13590 and other similar powered craft;
gondolas and pedalos;
sailing surfboards;
surfboards, including powered surfboards;
hydrofoils and hovercraft when not operating in the displacement mode; and
submersibles.
ISO 12217-1:2015 does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 12217-2:2015 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using ISO 12217-2:2015 will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum load.
ISO 12217-2:2015 is principally applicable to boats propelled primarily by sail (even if fitted with an auxiliary engine) of 6 m up to and including 24 m hull length. However, it can also be applied to boats less than 6 m if they are habitable multihulls or may be applied if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, ISO 12217-2:2015 includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
ISO 12217-2:2015 excludes:
inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217;
gondolas and pedalos;
surfboards including sailing surfboards; and
hydrofoils and foil stabilized boats when not operating in the displacement mode.
ISO 12217-2:2015 does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 9094:2015 defines a practical degree of fire prevention and protection intended to provide enough time for occupants to escape a fire on board small craft.
It applies to all small craft of up to 24 m length of hull (LH) except for personal watercraft.
ISO 9094:2015 excludes:
the design and installation of those permanently installed galley stoves and heating appliances (including components used to distribute the heat) using fuels that are liquid at atmospheric pressure on small craft, which are covered by ISO 14895;
carbon monoxide detecting systems, which are covered by ISO 12133.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 12217-3:2015 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of craft susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using ISO 12217-3:2015 will enable the boat to be assigned to a design category (C or D) appropriate to its design and maximum load.
ISO 12217-3:2015 is applicable to boats of hull length less than 6 m, whether propelled by human or mechanical power, except habitable sailing multihulls. Boats of hull length less than 6 m which are fitted with a full deck and quick-draining cockpit(s) complying with ISO 11812 may alternatively be assessed using ISO 12217‑1 or ISO 12217‑2 (for non-sailing and sailing boats, respectively), in which case higher design categories may be assigned.
In relation to habitable multihulls, ISO 12217-3:2015 includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
ISO 12217-3:2015 excludes:
inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217;
personal watercraft covered by ISO 13590 and other similar powered craft;
aquatic toys;
canoes and kayaks;
gondolas and pedalos;
sailing surfboards;
surfboards, including powered surfboards;
hydrofoils, foil stabilized boats and hovercraft when not operating in the displacement mode; and
submersibles.
NOTE Displacement mode means that the boat is only supported by hydrostatic forces.
ISO 12217-3:2015 does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day