EN ISO 6412-1:2018

SLOVENSKI STANDARD
01-april-2018
1DGRPHãþD
SIST EN ISO 6412-1:1998
7HKQLþQDGRNXPHQWDFLMDL]GHONRY3RHQRVWDYOMHQRSULND]RYDQMHFHYRYRGRY
GHO6SORãQDSUDYLODLQRUWRJRQDOQRSULND]RYDQMH,62
Technical product documentation - Simplified representation of pipelines - Part 1:
General rules and orthogonal representation (ISO 6412-1:2017)
Documentation technique de produits - Représentation simplifiée des tuyaux et lignes de
tuyauteries - Partie 1: Règles générales et représentation orthogonale (ISO 6412-
1:2017)
Ta slovenski standard je istoveten z: EN ISO 6412-1:2018
ICS:
01.100.20 Konstrukcijske risbe Mechanical engineering
drawings
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 6412-1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 01.100.99; 23.040.01 Supersedes EN ISO 6412-1:1994
English Version
Technical product documentation - Simplified
representation of pipelines - Part 1: General rules and
orthogonal representation (ISO 6412-1:2017)
Documentation technique de produits - Représentation
simplifiée des tuyaux et lignes de tuyauteries - Partie 1:
Règles générales et représentation orthogonale (ISO
6412-1:2017)
This European Standard was approved by CEN on 22 October 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6412-1:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 6412-1:2018) has been prepared by Technical Committee ISO/TC 10 “Process
plant documentation”.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6412-1:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6412-1:2017 has been approved by CEN as EN ISO 6412-1:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 6412-1
Second edition
2017-12
Technical product documentation —
Simplified representation of
pipelines —
Part 1:
General rules and orthogonal
representation
Documentation technique de produits — Représentation simplifiée
des tuyaux et lignes de tuyauteries —
Partie 1: Règles générales et représentation orthogonale
Reference number
ISO 6412-1:2017(E)
©
ISO 2017
ISO 6412-1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 6412-1:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General principles . 2
4.1 Overview . 2
4.2 Representation of pipes . 2
4.3 Scale . 2
4.4 Lines . 2
4.4.1 Line thickness . 2
4.4.2 Types of line . 3
4.4.3 Spacing of lines . 3
4.5 Lettering . 3
4.6 Dimensioning . 4
4.7 Tolerances . 5
5 Crossings and connections . 5
6 Representation of equipment . 6
6.1 General . 6
6.2 Fittings . 6
6.3 Supports and hangers . 7
6.4 Additional provisions . 8
6.5 Adjoining apparatus . 8
6.6 Direction of flow . 8
6.7 Flanges . 8
7 Examples . 9
Bibliography .11
ISO 6412-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 10, Technical drawings, Subcommittee
SC 10, Process plant documentation.
This second edition cancels and replaces the first edition (ISO 6412-1:1989), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the normative references were updated;
— the document went under editorial revision.
A list of all parts in the ISO 6412 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

ISO 6412-1:2017(E)
Introduction
Depending on the information it is intended to convey and the form of representation required, a
distinction is made between graphical representation by means of orthogonal and that by means of
isometric representation.
This document deals with general rules used for both representations (orthogonal an
...