ISO 128-43:2015
(Main)Technical product documentation (TPD) — General principles of presentation — Part 43: Projection methods in building drawings
Technical product documentation (TPD) — General principles of presentation — Part 43: Projection methods in building drawings
ISO 128-43:2015 defines two projection methods used in building drawings, namely ? direct orthographic projection method and ? mirrored orthographic projection method, and also provides the symbols applicable for each method.
Documentation technique de produits (TPD) — Principes généraux de représentation — Partie 43: Méthodes de projection dans les dessins de bâtiment
Tehnična proizvodna dokumentacija (TPD) - Splošna načela prikazovanja - 43. del: Projekcijske metode pri stavbnih risbah
Ta del standarda ISO 128 določa dve projekcijski metodi, ki se uporabljata pri stavbnih risbah, in sicer
– direktno ortografsko projekcijsko metodo in
– zrcaljeno ortografsko projekcijsko metodo,
ter podaja simbole za posamezno metodo.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 128-43:2016
01-junij-2016
1DGRPHãþD
SIST ISO 2594:1995
7HKQLþQDSURL]YRGQDGRNXPHQWDFLMD 73' 6SORãQDQDþHODSULND]RYDQMDGHO
3URMHNFLMVNHPHWRGHSULVWDYEQLKULVEDK
Technical product documentation (TPD) - General principles of presentation - Part 43:
Projection methods in building drawings
Documentation technique de produits (TPD) - Principes généraux de représentation -
Partie 43: Méthodes de projection dans les dessins de bâtiment
Ta slovenski standard je istoveten z: ISO 128-43:2015
ICS:
01.100.30 *UDGEHQLQDþUWL Construction drawings
SIST ISO 128-43:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 128-43:2016
---------------------- Page: 2 ----------------------
SIST ISO 128-43:2016
INTERNATIONAL ISO
STANDARD 128-43
First edition
2015-07-01
Technical product documentation
(TPD) — General principles of
presentation —
Part 43:
Projection methods in building
drawings
Documentation technique de produits (TPD) — Principes généraux de
représentation —
Partie 43: Méthodes de projection dans les dessins de bâtiment
Reference number
ISO 128-43:2015(E)
©
ISO 2015
---------------------- Page: 3 ----------------------
SIST ISO 128-43:2016
ISO 128-43:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 128-43:2016
ISO 128-43:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Direct orthographic projection . 1
3 Mirrored orthographic projection . 2
4 Symbolization . 2
© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 128-43:2016
ISO 128-43:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the
...
INTERNATIONAL ISO
STANDARD 128-43
First edition
2015-07-01
Technical product documentation
(TPD) — General principles of
presentation —
Part 43:
Projection methods in building
drawings
Documentation technique de produits (TPD) — Principes généraux de
représentation —
Partie 43: Méthodes de projection dans les dessins de bâtiment
Reference number
ISO 128-43:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 128-43:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 128-43:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Direct orthographic projection . 1
3 Mirrored orthographic projection . 2
4 Symbolization . 2
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 128-43:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. D
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.