EN 13411-2:2001+A1:2008
(Main + Amendment)Terminations for steel wire ropes - Safety - Part 2: Splicing of eyes for wire rope slings
Terminations for steel wire ropes - Safety - Part 2: Splicing of eyes for wire rope slings
This standard specifies minimum requirements for the splicing of eye terminations for six or eight strand steel wire ropes of up to 60 mm diameter complying with prEN 12385-4 used for slings to ensure that the spliced eye is strong enough to withstand a force of at least 80 % of the minimum breaking load of the rope.
Other hazards covered by this standard are identified in clause 4. Resistance to fatigue loading is not considered to be a significant hazard for slings and is not covered by this standard.
Endverbindungen für Stahldrahtseile - Sicherheit - Teil 2: Spleißen von Seilschlaufen für Anschlagseile
Diese Norm legt Mindestanforderungen für das Spleißen von Schlaufen bei 6 oder 8 litzigen Drahtseilen aus Stahldraht nach EN 12385 4 bis zu einem Durchmesser von 60 mm, die für Anschlagseile verwendet werden, fest, um sicherzustellen, dass die Schlaufe fest genug ist, um eine Kraft von mindestens 80 % der Mindest¬bruchkraft des Seiles zu ertragen.
Andere Gefährdungen, die durch diese Norm abgedeckt werden, sind in Abschnitt 4 angegeben. Versagen durch Ermüdung wird nicht als eine für Anschlagseile charakteristische Gefährdung angesehen und wird in dieser Norm nicht behandelt.
Terminaisons pour câbles en acier - Sécurité - Partie 2: Epissures de boucles pour élingues en câbles d'acier
La présente norme européenne fixe les prescriptions minimales auxquelles doivent répondre les boucles épissées
des élingues en câbles en acier à six ou huit torons, de diamètre !jusqu’à" 60 mm conformément au
prEN 12385-4, qui sont utilisées pour les élingues afin d’assurer que les boucles épissées soient suffisamment fortes
pour résister à une charge d’au moins 80 % de la charge de rupture minimale du câble.
L'article 4 identifie les autres phénomènes dangereux couverts par la présente norme. La résistance de la charge de
fatigue n’est pas considérée comme un risque significatif et n’est pas couvert par la présente norme.
Zaključki jeklenih žičnih vrvi - Varnost - 2. del: Spletanje zank na vrvnih obesah
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Endverbindungen für Stahldrahtseile - Sicherheit - Teil 2: Spleißen von Seilschlaufen für AnschlagseileTerminaisons pour câbles en acier - Sécurité - Partie 2: Epissures de boucles pour élingues en câbles d'acierTerminations for steel wire ropes - Safety - Part 2: Splicing of eyes for wire rope slings77.140.99Drugi železni in jekleni izdelkiOther iron and steel products53.020.30Pribor za dvigalno opremoAccessories for lifting equipmentICS:Ta slovenski standard je istoveten z:EN 13411-2:2001+A1:2008SIST EN 13411-2:2001+A1:2008en,fr01-december-2008SIST EN 13411-2:2001+A1:2008SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13411-2:2001+A1
October 2008 ICS 21.060.70; 53.020.30 Supersedes EN 13411-2:2001 English Version
Terminations for steel wire ropes - Safety - Part 2: Splicing of eyes for wire rope slings
Terminaisons pour câbles en acier - Sécurité - Partie 2: Epissures de boucles pour élingues en câble d'acier
Endverbindungen für Stahldrahtseile - Sicherheit - Teil 2: Spleißen von Seilschlaufen für Anschlagseile This European Standard was approved by CEN on 20 April 2001 and includes Amendment 1 approved by CEN on 18 September 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13411-2:2001+A1:2008: ESIST EN 13411-2:2001+A1:2008
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 13411-2:2001+A1:2008
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.