EN 13411-7:2021

SLOVENSKI STANDARD
01-september-2021
Nadomešča:
SIST EN 13411-7:2006+A1:2008
Zaključki jeklenih žičnih vrvi - Varnost - 7. del: Simetrični zagozdni spoji
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 7: Symmetrische
Seilschlösser
Terminaisons pour câbles en acier - Sécurité - Partie 7: Boîte à coin symétrique
Ta slovenski standard je istoveten z: EN 13411-7:2021
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
77.140.99 Drugi železni in jekleni izdelki Other iron and steel products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13411-7
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2021
EUROPÄISCHE NORM
ICS 21.060.70; 53.020.30; C Supersedes EN 13411-7:2006+A1:2008
English Version
Terminations for steel wire ropes - Safety - Part 7:
Symmetric wedge socket
Terminaisons pour câbles en acier - Sécurité - Partie 7 : Endverbindungen für Drahtseile aus Stahldraht -
Boîte à coin symétrique Sicherheit - Teil 7: Symmetrische Seilschlösser
This European Standard was approved by CEN on 28 April 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13411-7:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 List of significant hazards . 8
5 Safety requirements and/or measures . 8
5.1 Geometry of wedge and socket body . 8
5.2 Security of the pin . 9
5.3 Welded socket body . 9
5.4 Mechanical properties . 9
5.4.1 General . 9
5.4.2 Termination efficiency . 9
5.4.3 Fatigue behaviour of the socket body and pin . 9
5.4.4 Low temperature properties . 9
6 Verification of safety requirements . 10
6.1 Qualifications of personnel. 10
6.2 Type testing . 10
6.2.1 General . 10
6.2.2 Tensile efficiency test . 10
6.2.3 Fatigue test . 10
6.2.4 Acceptance criteria for type testing . 10
6.2.5 Charpy impact test . 11
6.3 Manufacturing tests and examination . 11
6.3.1 Manufacturers tests . 11
6.3.2 Visual examination of welded socket bodies . 11
6.3.3 Weld testing . 12
6.4 Manufacturing test and examination regime and acceptance criteria . 12
7 Information for use . 12
7.1 Marking . 12
7.2 Fitting instructions . 13
7.3 Manufacturer's certificate . 13
Annex A (informative) Construction and sizes for one design of symmetric wedge
socket with welded socket body . 14
A.1 General . 14
A.2 Material . 14
A.3 Dimensions . 14
Annex B (informative) Recommendations for safe use and inspection of symmetric
wedge sockets conforming to Annex A . 17
B.1 General . 17
B.2 Method of assembly . 17
B.3 Inspection in use . 18
Bibliography . 19
European foreword
This document (EN 13411-7:2021) has been prepared by Technical Committee CEN/TC 168
“Chains, ropes, webbing, slings and accessories - Safety”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2022, and conflicting national
standards shall be withdrawn at the latest by January 2022.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 13411-7:2006+A1:2008.
The main changes compared to the previous edition are listed below:
— a major change to 6.4;
— updates to standard references;
— coefficient of utilisation changed from 10:1 to 12:1 for lifting persons – 5.4.1.
EN 13411 consists of the following parts:
— Part 1: Thimbles for steel wire rope slings;
— Part 2: Splicing of eyes for steel wire rope slings;
— Part 3: Ferrules and ferrule-securing;
— Part 4: Metal and resin socketing;
— Part 5: U-bolt wire rope grips;
— Part 6: Asymmetric wedge socket;
— Part 7: Symmetric wedge socket;
— Part 8: Swage terminals and swaging;
— Part 9: Solid thimbles.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
This European standard is a type C standard as stated in EN ISO 12100.
This part of this European standard has been prepared to provide a means of conforming with
the essential safety requirements of the Machinery Directive and the Lift Directive and
associated EFTA regulations.
The wedge socket concerned and the extent to which hazards, hazardous situations and events
are covered are indicated in the scope of this standard part of the standard.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the provisions of the
other standards for symmetric wedge sockets that have been designed and produced according
to the provisions of this type C standard.
Purchasers ordering to this standard are advised to specify in their purchasing contract that the
supplier operates a quality assurance system applicable to the relevant part of this standard
(e.g. EN ISO 9001) to ensure themselves that products claiming to comply consistently achieve
the required level of quality.
1 Scope
This document specifies the minimum requirements for symmetrical wedge socket
terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This document covers those symmetric wedge sockets intended for use at temperatures
between −20 °C and 100 °C.
This document only covers those symmetric wedge sockets that have welded socket bodies. An
example of the construction and sizes of a symmetric wedge socket is given in informative
Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of
symmetric wedge socket according to Annex A.
This document deals with all significant hazards, hazardous situations and events relevant to
symmetric wedge sockets for terminations for steel wire ropes, when used as intended and
under conditions of misuse which are reasonably foreseeable by the manufacturer.
The hazards covered by this document are identified in Clause 4.
This document applies to symmetric wedge sockets, which are manufactured after the date of
its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition cited
applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 12385-2:2002+A1:2008, Steel wire ropes — Safety — Part 2: Definitions, designation and
classification
EN 12385-5:2021, Steel wire ropes — Safety — Part 5: Stranded ropes for lifts
EN ISO 148-1:2016, Metallic materials — Charpy pendulum impact test — Part 1: Test method
(ISO 148-1:2016)
EN ISO 4063:2010, Welding and allied processes — Nomenclature of processes and reference
numbers (ISO 4063:2009, Corrected version 2010-03-01)
EN ISO 5817:2014, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys
(beam welding excluded)
...