Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings

This European Standard specifies the minimum requirements for non welded general purpose steel thimbles produced from plate having dimensions in accordance with Figure 1. The thimbles are intended to be used in slings made with six or eight strand steel wire ropes from 8 mm to 60 mm diameter complying with EN 12385-4.
Reeving thimbles and solid thimbles are not covered by this standard.
The hazards covered by this standard are identified in clause 4.

Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 1: Kauschen für Anschlagseile aus Stahldrahtseilen

Diese Europäische Norm legt die Mindestanforderungen an nichtgeschweißte Stahlkauschen aus Blech für allgemeine Zwecke mit Maßen nach Bild 1 fest. Die Kauschen sind zur Verwendung bei Anschlagseilen, die aus 6  oder 8 litzigen Drahtseilen aus Stahldraht nach EN 12385-4 mit Durchmessern von 8 mm bis 60 mm hergestellt sind, bestimmt.
Durchsteck  und Vollkauschen sind nicht Gegenstand dieser Norm.
Gefährdungen, die in dieser Norm behandelt werden, sind in Abschnitt 4 angegeben.

Terminaisons pour câbles en acier - Sécurité - Partie 1: Cosses pour élingues en câbles d'acier

La présente Norme européenne spécifie les prescriptions minimales pour l’aptitude à l’emploi des cosses en acier
non soudées d’usage courant, produites à partir d’une plaque dont les dimensions sont conformes à la Figure 1.
Les cosses sont destinées à être utilisées en élingues composées de 6 ou 8 torons en acier, de diamètre compris
entre 8 mm et 60 mm, conformément à l'EN 12385-4.
Les cosses à engagement simple et les cosses pleines ne sont pas couvertes par la présente norme.
L'article 4 identifie les phénomènes dangereux couverts par la présente norme.

Zaključki jeklenih žičnih vrvi - Varnost - 1. del: Vrvna srca za obesne zanke jeklenih žičnih vrvi

General Information

Status
Published
Publication Date
21-Oct-2008
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
04-Jun-2023
Completion Date
04-Jun-2023

Relations

Buy Standard

Standard
EN 13411-1:2003+A1:2008
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 1: Kauschen für Anschlagseile aus DrahtseilenTerminaisons pour câbles en acier - Sécurité - Partie 1: Cosses pour élingues en câbles d'acierTerminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings77.140.99Drugi železni in jekleni izdelkiOther iron and steel products53.020.30Pribor za dvigalno opremoAccessories for lifting equipmentICS:Ta slovenski standard je istoveten z:EN 13411-1:2002+A1:2008SIST EN 13411-1:2003+A1:2008en,fr01-december-2008SIST EN 13411-1:2003+A1:2008SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13411-1:2002+A1
October 2008 ICS 21.060.70; 53.020.30 Supersedes EN 13411-1:2002 English Version
Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings
Terminaisons pour câbles en acier - Sécurité - Partie 1: Cosses pour élingues en câbles d'acier
Endverbindungen für Drahtseile aus Stahldraht -Sicherheit - Teil 1: Kauschen für Anschlagseile aus Drahtseilen This European Standard was approved by CEN on 11 November 2001 and includes Amendment 1 approved by CEN on 18 September 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13411-1:2002+A1:2008: ESIST EN 13411-1:2003+A1:2008

!!!!Relationship between this European standard and the Essential Requirements of EU Directive 98/37/EC"""".9 Annex ZB (informative)
!!!!Relationship between this European standard and the Essential Requirements of EU Directive 2006/42/EC"""".10 Bibliography.11
(e.g. EN ISO 9001) to ensure themselves that products claiming to comply consistently achieve the required level of quality. While producing this standard it was assumed that negotiation occurs between the manufacturer and the user to decide whether the thimble shall have a pointed or truncated end and whether zinc coating is required. 1 Scope This European Standard specifies the minimum requirements for non welded general purpose steel thimbles produced from plate having dimensions in accordance with Figure 1. The thimbles are
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.