iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 17268:2020

(Main)

Gaseous hydrogen land vehicle refuelling connection devices (ISO/FDIS 17268:2019)

Gaseous hydrogen land vehicle refuelling connection devices (ISO/FDIS 17268:2019)

This document defines the design, safety and operation characteristics of gaseous hydrogen land vehicle (GHLV) refuelling connectors.
GHLV refuelling connectors consist of the following components, as applicable:
—     receptacle and protective cap (mounted on vehicle);
—     nozzle;
—     communication hardware.
This document is applicable to refuelling connectors which have nominal working pressures or hydrogen service levels up to 70 MPa.
This document is not applicable to refuelling connectors dispensing blends of hydrogen with natural gas.

Anschlussvorrichtungen für die Betankung von Landfahrzeugen mit gasförmigem Wasserstoff (ISO 17268:2020)

Dieses Dokument legt die Auslegung, die Sicherheit und die betrieblichen Eigenschaften von Anschlüssen zur Betankung von Landfahrzeugen, die mit gasförmigem Wasserstoff (GHLV; en: gaseous hydrogen land vehicle) betrieben werden, fest.
GHLV-Betankungsanschlüsse bestehen ggf. aus den folgenden Bauteilen:
—   Empfängerstutzen und Schutzkappe (am Fahrzeug angebracht);
—   Füllstutzen;
—   Kommunikations-Hardware.
Dieses Dokument gilt für Betankungsanschlüsse mit Nennbetriebsdrücken oder Wasserstoffbetriebsstufen von bis zu 70 MPa.
Betankungsanschlüsse zur Abgabe von Wasserstoff-Erdgas-Gemischen sind vom Anwendungsbereich dieses Dokuments ausgeschlossen.

Dispositifs de raccordement pour le ravitaillement des véhicules terrestres en hydrogène gazeux (ISO/FDIS 17268:2019)

Le présent document définit les caractéristiques de conception, de sécurité et d'exploitation des connecteurs destinés au ravitaillement des véhicules terrestres à hydrogène gazeux (GHLV).
Les connecteurs de ravitaillement des GHLV sont constitués des éléments suivants, selon le cas:
—          un réceptacle et un bouchon de protection (montés sur le véhicule);
—          un pistolet;
—          un module de communication.
Le présent document s'applique aux connecteurs de ravitaillement ayant une pression de service nominale ou un niveau de service d'hydrogène ne dépassant pas 70 MPa.
Le présent document ne s'applique pas aux connecteurs de ravitaillement servant à distribuer des mélanges d'hydrogène et de gaz naturel.

Priključne naprave za oskrbo kopenskih vozil s plinastim vodikom (ISO 17268:2020)

General Information

Status
Published
Publication Date
25-Feb-2020
Withdrawal Date
30-Aug-2020
ICS
43.180 - Diagnostic, maintenance and test equipment
71.100.20 - Gases for industrial application
Technical Committee
CEN/TC 268 - Cryogenic vessels
Drafting Committee
CEN/TC 268/WG 5 - Specific hydrogen technologies applications
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
26-Feb-2020
Completion Date
26-Feb-2020
Directive
2014/94/EU - Directive 2014/94/EU of The European Parliament and of The Council of 22 October 2014 on the deployment of alternative fuels infrastructure
Mandate
M/533 - [C(2015)1330] Standardisation request addressed to CEN, CENELEC and ETSI in support of the implementation of the Directive 2014/94/EU on the deployment of alternative fuels infrastructure
Ref Project
SIST EN ISO 17268:2020 - Gaseous hydrogen land vehicle refuelling connection devices (ISO 17268:2020)

Relations

Replaces
EN ISO 17268:2016 - Gaseous hydrogen land vehicle refuelling connection devices (ISO 17268:2012)
Effective Date
04-Mar-2020
Revised
prEN ISO 17268-1 - Gaseous hydrogen land vehicle refuelling connection devices - Part 1: Flow capacities up to and including 120 g/s (ISO/DIS 17268-1:2024)
Effective Date
19-Jan-2023

Buy Standard

EN ISO 17268:2020EN ISO 17268:2020
PreviousNext
Standard
EN ISO 17268:2020
English language
53 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2020
Nadomešča:
SIST EN ISO 17268:2017
Priključne naprave za oskrbo kopenskih vozil s plinastim vodikom (ISO
17268:2020)
Gaseous hydrogen land vehicle refuelling connection devices (ISO 17268:2020)
Gasförmiger Wasserstoff - Anschlussvorrichtungen für die Betankung von
Landfahrzeugen (ISO 17268:2020)
Dispositifs de raccordement pour le ravitaillement des véhicules terrestres en hydrogène
gazeux (ISO 17268:2020)
Ta slovenski standard je istoveten z: EN ISO 17268:2020
ICS:
43.180 Diagnostična, vdrževalna in Diagnostic, maintenance and
preskusna oprema test equipment
71.100.20 Industrijski plini Gases for industrial
application
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 17268
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 43.180; 71.100.20 Supersedes EN ISO 17268:2016
English Version
Gaseous hydrogen land vehicle refuelling connection
devices (ISO 17268:2020)
Dispositifs de raccordement pour le ravitaillement des
véhicules terrestres en hydrogène gazeux (ISO
17268:2020)
This European Standard was approved by CEN on 24 January 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17268:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 17268:2020) has been prepared by Technical Committee ISO/TC 197
"Hydrogen technologies" in collaboration with Technical Committee CEN/TC 268 “Cryogenic vessels
and specific hydrogen technologies applications” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2020, and conflicting national standards shall
be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17268:2016.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 17268:2020 has been approved by CEN as EN ISO 17268:2020 without any modification.

INTERNATIONAL ISO
STANDARD 17268
Third edition
2020-02
Gaseous hydrogen land vehicle
refuelling connection devices
Dispositifs de raccordement pour le ravitaillement des véhicules
terrestres en hydrogène gazeux
Reference number
ISO 17268:2020(E)
©
ISO 2020
ISO 17268:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 17268:2020(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General construction requirements . 3
5 Nozzles . 5
6 Receptacles . 7
7 Design verification test procedures. 8
7.1 General requirements . 8
7.2 Test conditions . 8
7.3 Nozzle tests . 8
7.4 Receptacle tests . 8
7.5 User — Machine interface . 8
7.6 Dropping . 9
7.7 Leakage at room temperature . 9
7.8 Valve operating handle .10
7.9 Receptacle vibration resistance .10
7.10 Abnormal loads .10
7.11 Low and high temperatures .11
7.11.1 Purpose .11
7.11.2 General.11
7.11.3 Leakage tests .11
7.11.4 Operation tests .11
7.12 Durability and maintainability .12
7.12.1 Purpose .12
7.12.2 Nozzle durability test .12
7.12.3 Receptacle check valve durability test .13
7.12.4 Receptacle durability test .13
7.12.5 Connected nozzle and receptacle durability test .13
7.13 Sealing material aging test .13
7.13.1 Purpose .13
7.13.2 Oxygen aging test procedure .14
7.13.3 Ozone aging test procedure .14
7.14 Non-metallic material hydrogen resistance test .14
7.15 Electrical resistance .14
7.16 Hydrostatic strength .14
7.17 Corrosion resistance .15
7.17.1 Purpose .15
7.17.2 General.15
7.17.3 Nozzle test .15
7.17.4 Receptacle test .15
7.18 Deformation .15
7.19 Contamination test .15
7.20 Thermal cycle test .16
7.21 Pre-cooled hydrogen exposure test .16
7.22 Misconnected nozzle test .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 19085-9:2024(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)
SIST EN ISO 19085-9:2024

This document specifies the safety requirements and measures for circular saw benches with or without sliding table or demountable power feed unit or both and capable of continuous production use, also known as “table saws” (in the USA), hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices or working units, whose hazards have been dealt with:
—     device for the main saw blade and scoring saw blade to be raised and lowered through the table;
—     device to tilt the main saw blade and scoring saw blade for angled cutting;
—     device for scoring;
—     device for grooving with milling tool with a width not exceeding 20 mm in one pass;
—     demountable power feed unit;
—     additional manually operated sliding table;
—     powered workpiece clamping device.
This document does not apply to:
a)       machines intended for outdoor use on building sites;
NOTE            Building site saws (contractor saws) are covered by the requirements of ISO 19085-10:2018.
b)       handheld woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;
c)        machines intended for use in a potentially explosive atmosphere;
d)       machines manufactured prior to the publication of this document.

  • Draft
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-2:2024(Main)
Gas infrastructure - Injection stations - Part 2: Specific requirements regarding the injection of biomethane
kSIST FprEN 17928-2:2024

This document establishes specific functional requirements for injection stations for biomethane into gas transmission and distribution systems operated with gases of the second gas family in accordance with EN 437 in addition to the general functional requirements of EN 17928 1:2024.
This document represents the recommendations at the time of its preparation. This document does not apply to injection stations operating prior to the publication of this document.
This document complements EN 17928 1:2024 by specifying the technical safety requirements to be observed in respect of the chemical and physical properties of biomethane.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16186-6:2024(Main)
Railway applications - Driver's cab - Part 6: Integration of displays, controls and indicators for tram vehicles
SIST EN 16186-6:2024

This document is applicable to vehicles operating on tram networks.
This document gives design requirements and guidance in order to ensure visibility and operability of displays, controls and indicators in the cab in all operating conditions (day, night, natural or artificial lighting).
It covers four aspects:
-   the characteristics of the displays, controls and indicators in order to ensure proper visibility: i.e. range of luminance and contrast as well as the possibility of adjustment of perceived brightness;
-   the requirements for the location of the displays, keyboards, controls and indicators in the cab and on the driver’s desk: i.e. position, angle of visibility, etc. with consideration of the normal driving position and the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.);
-   the characteristics and requirements for the location of microphones and loudspeakers;
-   design of symbols.
NOTE   All element numbers within the text refer to Table B.1.
This document does not apply to refurbishment of existing vehicles. This document is not intended to be applicable to driver's auxiliary desk, except for 5.3.13, Clause 6, 7.1.2, Clause 9 and Table B.1.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-8:2024(Main)
Woodworking machines - Safety - Part 8: Wide belt sanding machines and surface treating machines (ISO 19085-8:2024)
SIST EN ISO 19085-8:2024

This document specifies the safety requirements and measures for wide belt sanding machines (defined in 3.1) and for surface treating machines (defined in 3.2) capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     transversal sanding unit;
—     cleaning brushing unit;
—     satining roller unit;
—     disk brushing unit;
—     texturing brushing roller unit;
—     texturing brushing belt unit;
—     cutterblock unit;
—     texturing band saw unit;
—     spiked roller unit;
—     multi blade unit;
—     conveyor directly controlled by the machine;
—     additional workpiece vacuum clamping device;
—     antistatic bar unit.
NOTE 1        An antistatic bar is a device that eliminates electrostatic charges on the workpiece to ease its subsequent cleaning from dust by airflow.
This document is also applicable to machines fitted with a laser engraving unit, but the specific hazards of this unit have not been dealt with.
The machines are designed to process workpieces with flat surface and even thickness, in shape of panels or beams or frames, consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        gypsum boards, gypsum bounded fibreboards;
d)       composite materials with core consisting of, e.g. polyurethane or mineral material;
e)       composite boards made from the materials listed above;
f)         all materials listed above, already lacquered.
This document does not deal with hazards related to:
—     specific devices other than those listed above;
—     access through in-feed and out-feed openings of machines with a work piece height capacity greater than 700 mm;
—     systems for powered loading or unloading, or both, of the workpiece to or from a single machine;
NOTE 2        Loading the machine manually includes manually placing the workpiece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the workpiece from a conveyor directly controlled by the machine.
—     out-feed workpieces on machines with feed speed higher than 60 m/min;
—     interfacing of the machine with any other machine.
This document is not applicable to machines intended for use in a potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17450-2:2024(Main)
Fixed firefighting systems - Water mist systems - Part 2: Product characteristics and test methods for nozzles
kSIST FprEN 17450-2:2024

This document specifies product characteristics and test methods of open nozzles and automatic nozzles for use in water mist systems.
NOTE   All pressure data in this document are given as gauge pressures in bar.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-1:2024(Main)
Gas infrastructure - Injection stations - Part 1: General requirements
kSIST FprEN 17928-1:2024

This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14105:2024(Main)
Fat and oil derivatives - Fatty Acid Methyl Esters (FAME) - Determination of free and total glycerol and mono-, di-, triglyceride contents
kSIST FprEN 14105:2024

This document specifies a method to determine the free glycerol and residual mono-, di- and triglyceride contents in fatty acid methyl esters (FAME). The total glycerol content is then calculated from the obtained results.
Under the conditions described, the quantification limits are 0,001 % (m/m) for free glycerol, 0,10 % (m/m) for all glycerides (mono-, di- and tri-). This method is suitable for FAME prepared from rapeseed, sunflower, soybean, palm, animal oils and fats and mixture of them. It is not suitable for FAME produced from or containing coconut and palm kernel oils derivatives because of overlapping of different glyceride peaks.
NOTE 1   For the purposes of this document, the term "% (m/m)" is used to represent the mass fraction.
NOTE 2   Under the common EN 14105 GC conditions, squalene can coelute with alpha glycerol monostearate. If the presence of squalene is suspected, EN 17057 can be used to discriminate between squalene and glycerol monostearate.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of users of this document to take appropriate measures to ensure the safety and health of personnel prior to application of the standard, and fulfil statutory and regulatory requirements for this purpose.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1591-1:2024(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation
SIST EN 1591-1:2024

This document defines a calculation method for bolted, gasketed, circular flange joints. Its purpose is to ensure structural integrity and control of leak tightness. It uses gasket parameters based on definitions and test methods specified in EN 13555:2014.
The calculation method is not applicable to joints with a metallic contact out of the sealing face or to joints whose rigidity varies appreciably across gasket width. For gaskets in incompressible materials, which permit large deformations, the results given by the calculation method can be excessively conservative (i.e. required bolting load too high, allowable pressure of the fluid too low, required flange thickness too large, etc.).

  • Draft
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13237:2024(Main)
Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
SIST EN 13237:2022

This document specifies terms and definitions (vocabulary) to be used in suitable standards dealing with equipment and protective systems intended for use in potentially explosive atmospheres within the scope of Directive 2014/34/EU.
NOTE   Terms and definitions avoid misunderstandings that are important in relation to the essential health and safety requirements of Directive 2014/34/EU.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 9300-001:2024(Main)
Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data - Part 001: Structure
kSIST FprEN 9300-001:2023

This document defines the structure and content for the long-term preservation of digital product and technical data. EN 9300 is broken into a series of separate standard parts to make the standard applicable for different business requirements and extensible for further long-term archiving formats.
The following outlines the total scope of this document:
-   for the purpose of this document, structure, and content of EN 9300 standard parts are detailed.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day