85.080 - Paper products
ICS 85.080 Details
Paper products
Papierwaren. Kartonagen
Produits en papier
Papirni izdelki
General Information
Frequently Asked Questions
ICS 85.080 is a classification code in the International Classification for Standards (ICS) system. It covers "Paper products". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 195 standards classified under ICS 85.080 (Paper products). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
e-Library Subscription
Create subscription and get permanent access to documents within 85.080 - Paper products
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers.
This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard.
This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers.
This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard.
This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers. This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard. This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies the requirements for permanent paper intended for documents. It is applicable to unprinted papers. It is not applicable to boards.
NOTE 1 The terms paper and board are defined in ISO 4046-3.
This document is not intended for judging the permanence of papers stored under hostile conditions, such as high humidity that can promote microbiological attack, excessive heat, radiation (light or other), high levels of atmospheric pollutants, or the influence of water.
NOTE 2 For information on International Standards on paper permanence (ISO 9706), on archival paper permanence and durability (ISO 11108), and on paper stability for general graphic applications (ISO 20494), refer to Annex D.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies the requirements for permanent paper intended for documents. It is applicable to unprinted papers. It is not applicable to boards.
NOTE 1 The terms paper and board are defined in ISO 4046-3.
This document is not intended for judging the permanence of papers stored under hostile conditions, such as high humidity that can promote microbiological attack, excessive heat, radiation (light or other), high levels of atmospheric pollutants, or the influence of water.
NOTE 2 For information on International Standards on paper permanence (ISO 9706), on archival paper permanence and durability (ISO 11108), and on paper stability for general graphic applications (ISO 20494), refer to Annex D.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies a basic laboratory test method for deinkability of woodfree printed paper products as a mixture under alkaline conditions by means of single stage flotation deinking and fatty acid-based collector chemistry. The woodfree printed paper product of interest is tested as a mixture containing 10 % by weight of the woodfree printed paper with the balance comprising a mixture of printed wood-containing paper.
- Standard23 pagesEnglish languagesale 15% off
This document covers physical properties and manufacturing requirements for envelopes having an address window and the flap on the front side once the flap has been sealed, hereafter the flap side. It covers the main design features of the reverse envelope, notably of the flap and address window, and the materials used for the manufacturing thereof. It applies to reverse envelopes with advertising or communication printed on the plain side, eventually on its entire surface.
This document covers empty envelopes, but also finished mailpieces that have been properly inserted, addressed and franked (reverse mailpieces) and are submitted to Postal Operators. In particular, reverse mailpieces will be compliant with relevant Postal standards applicable in the member states.
By extension, these requirements also apply to non-window envelopes used for reverse mailpieces and having the address printed on the flap side.
This document does not apply to:
- envelopes with a large window on the plain side (opposite to the flap) as these are already common and widely accepted,
- paper requirements to ensure print quality (except for the postage mark and address) and notably colour rendering.
- Technical specification15 pagesEnglish languagee-Library read for1 day
This document covers physical properties and manufacturing requirements for envelopes having an address window and the flap on the front side once the flap has been sealed, hereafter the flap side. It covers the main design features of the reverse envelope, notably of the flap and address window, and the materials used for the manufacturing thereof. It applies to reverse envelopes with advertising or communication printed on the plain side, eventually on its entire surface.
This document covers empty envelopes, but also finished mailpieces that have been properly inserted, addressed and franked (reverse mailpieces) and are submitted to Postal Operators. In particular, reverse mailpieces will be compliant with relevant Postal standards applicable in the member states.
By extension, these requirements also apply to non-window envelopes used for reverse mailpieces and having the address printed on the flap side.
This document does not apply to:
- envelopes with a large window on the plain side (opposite to the flap) as these are already common and widely accepted,
- paper requirements to ensure print quality (except for the postage mark and address) and notably colour rendering.
- Technical specification15 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps.
This document is not applicable to cases where impurities and contraries are determined.
- Standard22 pagesEnglish languagee-Library read for1 day
- Standard22 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps.
This document is not applicable to cases where impurities and contraries are determined.
- Standard22 pagesEnglish languagee-Library read for1 day
- Standard22 pagesEnglish languagee-Library read for1 day
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard20 pagesEnglish languagee-Library read for1 day
- Standard20 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation. Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps. This document is not applicable to cases where impurities and contraries are determined.
- Standard15 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard20 pagesEnglish languagee-Library read for1 day
- Standard20 pagesEnglish languagee-Library read for1 day
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing. This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary. It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
ABSTRACT
This specification covers pads of repositionable, colored, note paper. Each sheet has a strip of pressure-sensitive adhesive on the back side. A hand-operated steel roller shall be used in the manufacture of the pads and a cylindrical mandrel shall be used for flagging test of the pads. A minimum average of determined sheets of paper shall be assembled in the form of a pad. No individual pad shall contain less than a certain number of sheets. The pad of paper and a backing sheet shall be securely fastened together by means of the repositionable, pressure-sensitive adhesive coating. The paper to be used in the manufacture of the pad shall be determined by its basis weight and thickness. In order to determine the sheets' overall performance, the following properties shall be tested: writing quality, sheet removal, multiple sheet lift, fiber pull, initial flagging, and repositionable flagging. The sheets of pad paper shall be clean and free from dirt, foreign matter, holes, tears, wrinkles, and other defects which might affect appearance or serviceability. The sheets shall be uniform with respect to color and formation. Pads shall be square cut with smooth, clean edges.
SCOPE
1.1 This specification covers pads of repositionable, colored, note paper. Each sheet has a strip of pressure-sensitive adhesive on the back side.
1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification4 pagesEnglish languagesale 15% off
- Technical specification4 pagesEnglish languagesale 15% off
SIGNIFICANCE AND USE
4.1 Air permeability is an important factor in the performance of vacuum cleaner bag filter media, because it is a direct indicator of the resistance to air flow. It may also indicate the size of vacuum cleaner bag needed to achieve the desired air flow volume.
4.2 Performance specifications, both industrial and military, have been set up on the basis of air permeability and are used in the purchase of materials where permeability is of interest.
4.3 Since air permeability is not a linear function of pressure differential between paper surfaces, all tests should be made at a prescribed pressure differential, 0.5 in. (12.7 mm) of water.
SCOPE
1.1 This specification covers procedures to be followed for qualifying papers to be used in the manufacture of vacuum cleaner bags and filters. The filtration efficiency of the paper is not evaluated with the use of these test methods.
1.2 The procedures appear in the following sections:
Procedure
Sections
Air Permeability (Test Method D737)
3 – 5
Basis Weight (TAPPI Test Method T 410)
6 – 8
Bursting Strength (Mullen Test) (TAPPI Test Method T 403)
9 – 11
Internal Tearing Resistance (TAPPI Test Method T 414)
12 – 14
Tensile Breaking Strength (TAPPI Test Method T 494)
15 – 17
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification2 pagesEnglish languagesale 15% off
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in this document.
- Standard23 pagesEnglish languagee-Library read for1 day
SIGNIFICANCE AND USE
5.1 The plastic Petri plate (carrier) provides a closed system for enumeration and easy application of a pre-saturated or impregnated antimicrobial towelette by an analyst.
5.2 Aliquoting of sterile 5 % non-heat-inactivated fetal bovine serum (five 10 µL spots) onto soiled carriers and inoculation of final test suspension onto treated carriers (five 10 µL spots) is conducted using a template and a positive displacement pipette, thereby ensuring a precise inoculum level and uniform distribution of soil and final test suspension.
5.3 A single towelette is tested per 2-carrier set, eliminating the likelihood of cross contamination between carriers.
5.4 The corkscrew-patterned circular motion of the product application (wipe outside to inside, wipe inside to outside using the wiping template; see Annex A3 – Annex A6) ensures uniform coverage and contact of disinfectant with the inoculated surface.
5.5 The addition of neutralizer to the treated carriers at the end of the contact time results in neutralization of the test substance. This standard test method provides a procedure for performing neutralization verification to confirm that the microbicidal, microbistatic, or both types of activity of a test substance has been reduced by 50 % at the end of the contact time (see Annex A1 for neutralization verification procedure).
5.6 The design of this standard test method minimizes any loss of viable organisms through carrier wash-off.
5.7 It is optional to adjust (dilution in PBS) the inoculum to achieve desired control counts of 5.0 log10 CFU/carrier to 6.5 log10 CFU/carrier.
5.8 Include, where applicable, comparisons of the test to other similar procedures such as Practices E1054 and E2362.
SCOPE
1.1 This test method quantitatively determines the effectiveness of various sizes of antimicrobial towelettes in treating hard, non-porous surfaces against Pseudomonas aeruginosa and Staphylococcus aureus.
1.2 This test method may be used to evaluate towelettes for antimicrobial efficacy against additional microorganisms (with necessary modifications).
1.2.1 This test method does not differentiate between chemical inactivation of the test microbe and mechanical removal of inoculum from a surface; rather, product efficacy is considered a combination of both attributes of a towelette-based formulation.
1.3 This test method involves the use of hazardous materials, chemicals, and infectious microorganisms and therefore should be performed only by those trained in microbiological techniques in facilities designed and equipped for work with infectious agents at the appropriate biosafety level, a BSL-2 or higher laboratory; specifications provided in the “Biosafety for Biomedical and Microbiological Laboratories” (BMBL), 6th edition (BMBL).
1.4 It is the responsibility of the investigator to determine whether Good Laboratory Practices (GLP Standards—For example, 40 CFR, Part 160 of FIFRA) are required and to follow them when appropriate.
1.5 Strict adherence to the protocol is necessary for the validity of the test results.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard20 pagesEnglish languagesale 15% off
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in this document.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation. This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper. The calculation of perforation efficiency is also specified in this document.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.
This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard.
It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.
This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard.
It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis. This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard. It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the surface friction of tissue paper and tissue products using a contact-type surface tester.
- Standard11 pagesEnglish languagesale 15% off
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard18 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary. NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard10 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard19 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation. It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard20 pagesEnglish languagee-Library read for1 day
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard22 pagesEnglish languagee-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard20 pagesEnglish languagee-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary. NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard22 pagesEnglish languagee-Library read for1 day
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
This document defines a method for measuring the decolouration capability of commercial products, produced using paper and board dyed in mass and/or printed with dye inks. This document does not apply to paper printed with pigment inks.
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This document specifies a basic laboratory test method for deinkability, applicable to any kind of printed paper product, under alkaline conditions by means of single stage flotation deinking and fatty acid-based collector chemistry.
- Standard23 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard17 pagesEnglish languagee-Library read for1 day
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products.
For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard26 pagesEnglish languagee-Library read for1 day
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using an A-flute geometry.
The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.
NOTE ISO 7263-2 describes a method to determine the flat crush resistance using a B-flute geometry.
- Standard20 pagesEnglish languagee-Library read for1 day
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using a B-flute geometry.
The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.
NOTE ISO 7263-1 describes a method to determine the flat crush resistance using an A-flute geometry.
- Standard20 pagesEnglish languagee-Library read for1 day
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products.
For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard26 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard17 pagesEnglish languagee-Library read for1 day
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products. It permits the use of a common terminology in industry and commerce. It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products. For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard18 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using an A-flute geometry. The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board. NOTE ISO 7263-2 describes a method to determine the flat crush resistance using a B-flute geometry.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using a B-flute geometry. The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board. NOTE ISO 7263-1 describes a method to determine the flat crush resistance using an A-flute geometry.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ABSTRACT
This guide has been prepared to aid in the writing of material standards using the Classification D 4000 format.
SCOPE
1.1 This classification system covers ___ materials suitable for _____________. The inclusion or exclusion of recycled plastics in this classification system must be addressed here.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.
Note 1: Insert Note 1 here to show the appropriate ISO equivalency statement.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Guide5 pagesEnglish languagesale 15% off
- Guide5 pagesEnglish languagesale 15% off
ISO 12625-6:2016 specifies a test method for the determination of grammage of tissue paper and tissue products.
- Standard17 pagesEnglish languagee-Library read for1 day