17.200.99 - Other standards related to thermodynamics
ICS 17.200.99 Details
Other standards related to thermodynamics
Weitere thermodynamische Aspekte
Autres normes relatives a la thermodynamique
Drugi standardi v zvezi s termodinamiko
General Information
Frequently Asked Questions
ICS 17.200.99 is a classification code in the International Classification for Standards (ICS) system. It covers "Other standards related to thermodynamics". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 29 standards classified under ICS 17.200.99 (Other standards related to thermodynamics). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
This document specifies requirements for the measurement of preheating temperature, interpass temperature and preheat maintenance temperature for fusion welding. This document can also be applied as appropriate in the case of other welding processes. This document does not apply to the measurement of post weld heat treatment temperatures.
- Standard11 pagesEnglish languagee-Library read for1 day
This part of IEC 61340 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers).
This document establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and decay (charge neutralization) time for ionizers.
This document does not include measurements of electromagnetic interference (EMI), or the use of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices.
As contained in this document, the test methods and test conditions can be used by manufacturers of ionizers to provide performance data describing their products. Users of ionizers are urged to modify the test methods and test conditions for their specific application in order to qualify ionizers for use, or to make periodic verifications of ionizer performance. The user will decide the extent of the data required for each application.
See Annex A for information regarding theoretical background and additional information on the standard test method for the performance of ionizers.
CAUTION: Procedures and equipment described in this document can expose personnel to hazardous electrical and non-electrical conditions. Users of this document are responsible for selecting equipment that complies with applicable laws, regulatory codes and both external and internal policy. Users are cautioned that this document cannot replace or supersede any requirements for personnel safety. See Annex C for safety considerations.
- Standard34 pagesEnglish languagee-Library read for1 day
This part of IEC 61340 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers). This document establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and decay (charge neutralization) time for ionizers. This document does not include measurements of electromagnetic interference (EMI), or the use of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices. As contained in this document, the test methods and test conditions can be used by manufacturers of ionizers to provide performance data describing their products. Users of ionizers are urged to modify the test methods and test conditions for their specific application in order to qualify ionizers for use, or to make periodic verifications of ionizer performance. The user will decide the extent of the data required for each application. See Annex A for information regarding theoretical background and additional information on the standard test method for the performance of ionizers. CAUTION: Procedures and equipment described in this document can expose personnel to hazardous electrical and non-electrical conditions. Users of this document are responsible for selecting equipment that complies with applicable laws, regulatory codes and both external and internal policy. Users are cautioned that this document cannot replace or supersede any requirements for personnel safety. See Annex C for safety considerations.
- Standard34 pagesEnglish languagee-Library read for1 day
IEC 61340-4-7:2025 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers). This document establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and decay (charge neutralization) time for ionizers. This document does not include measurements of electromagnetic interference (EMI), or the use of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices. As contained in this document, the test methods and test conditions can be used by manufacturers of ionizers to provide performance data describing their products. Users of ionizers are urged to modify the test methods and test conditions for their specific application in order to qualify ionizers for use, or to make periodic verifications of ionizer performance. The user will decide the extent of the data required for each application.
This edition includes the following significant technical changes with respect to the previous edition:
a) in Figure 5, a NOTE 3 was added to clarify that for AC bars and grids, a single emitter alternating between +/− polarity is used;
b) in Annex B, the relative error for measurement equipment was updated to include the consideration for the resolution of the voltmeter.
- Standard95 pagesEnglish languagesale 15% off
This part of IEC 61340 provides electrical and mechanical test methods and performance limits for evaluation, acceptance and periodic verification testing of wrist straps. NOTE All dimensions are nominal except where indicated. This standard is intended for testing wrist straps and wrist strap systems used for the grounding of personnel engaged in working with ESD sensitive assemblies and devices. It does not address constant monitoring systems.
- Standard24 pagesEnglish languagee-Library read for1 day
IEC 61340-4-6:2025 provides electrical and mechanical test methods and performance limits for the evaluation, acceptance, and periodic verification testing of wrist straps. This document is intended for testing wrist straps and wrist strap systems used for the grounding of personnel engaged in working with ESD sensitive assemblies and devices. It does not address constant monitoring systems.
This edition includes the following significant technical changes with respect to the previous edition:
a) editorial comments made during the review of the second edition were reviewed and incorporated where appropriate;
b) normative references have been added to address the safety of equipment.
- Standard41 pagesEnglish and French languagesale 15% off
This part of IEC 61340 provides test methods for measuring the electrical resistance of garments used for static control applications. These test methods can be used for evaluating outer garments that are homogenously conductive or homogeneously dissipative, or that utilize surface conductive or surface dissipative components or elements. NOTE The test methods defined in this standard might not be able to measure materials with buried conductive layers. The resistance point-to-point test method tests the electrical resistance between the two sleeves, any two panels or any two or more electrically interconnected components of the static control garment, including the electrical resistance across the seams and cuffs of the garment as applicable. An alternate sleeve-to-sleeve test method is allowed, using clamps to hang a garment. Static control garments that electrically bond to the wearer and provide a path to ground from the wearer are evaluated using the resistance point-to-point test method, the resistance point to groundable point test method, as well as a system test to determine the resistance from the person through the garment to the groundable point of the garment system. A band resistance measurement test is provided in IEC 61340-4-6 which can be used for garments so equipped with cuffs that are intended to perform the same function as a wrist strap band. The system test with a person wearing a groundable static control garment system includes the ground cord that connects to the groundable point of the garment.
- Standard26 pagesEnglish languagee-Library read for1 day
IEC 61340-4-9:2024 provides test methods for measuring the electrical resistance of garments used for static control applications. These test methods can be used for evaluating outer garments that are homogenously conductive or homogeneously dissipative, or that utilize surface conductive or surface dissipative components or elements.
NOTE It is possible that the test methods defined in this document will not be able to measure materials with buried conductive layers.
This third edition includes the following significant technical changes with respect to the previous edition:
a) IEC 61010-1 and IEC 61010-2-030 added as requirements for measurement equipment;
b) testing voltage range for personnel ground path changed from "7 V DC to 30 V DC" to "7 V DC to 100 V DC";
c) cleaning requirements changed from a minimum of five cycles of cleaning to a minimum of three cycles of cleaning;
d) moderate humidity requirements deleted;
e) figures replaced with generic drawings.
- Standard77 pagesEnglish languagesale 15% off
IEC 60455-2:2023 is available as IEC 60455-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60455-2:2023 specifies methods of test to be used for testing resin based reactive compounds, their components and cured compounds used for electrical insulation. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Introduction of test methods related to IEC 60455-3-8;
b) Additional and updated test methods for resins.
- Standard41 pagesEnglish languagee-Library read for1 day
IEC 60455-2:2023 is available as IEC 60455-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60455-2:2023 specifies methods of test to be used for testing resin based reactive compounds, their components and cured compounds used for electrical insulation. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Introduction of test methods related to IEC 60455-3-8; b) Additional and updated test methods for resins.
- Standard41 pagesEnglish languagee-Library read for1 day
SIGNIFICANCE AND USE
5.1 Thermogravimetry provides a rapid method for determining the thermal decomposition and reaction mass change of a material.
5.2 This test method is useful in detecting potentially hazardous reactions and in estimating the temperatures at which these reactions occur. This test method is recommended as a screening test for detecting the thermal hazards of an uncharacterized material or mixture (see Section 8).
5.3 Energetic materials, pharmaceuticals and polymers are examples of materials for which this test might be useful. This test is especially useful for materials having melting points that overlap with the onset of reaction or decomposition.
Note 1: In differential scanning calorimetry (DSC), the melting endotherm may interfere with the determination of the onset temperature for reaction or decomposition.
5.4 This test is not suitable for materials that sublime or vaporize in the temperature range of interest. A sample with volatile impurities needs to be purified prior to testing by thermogravimetric analysis. Alternatively, the sample can be tested as is, however, special caution is required during the data analysis. The mass loss due to the loss of impurity should not interfere with the determination of reaction or decomposition temperature.
5.5 The four significant criteria of this test method are: the detection of a sample mass change; the extent of the mass change; the approximate temperature at which the event occurs; the observance of effects due to the atmosphere.
SCOPE
1.1 This test method describes the assessment of material thermal stability through the determination of the temperature at which the materials start to decompose or react and the extent of the mass change using thermogravimetry. The test method uses minimum quantities of material and is applicable over the temperature range from ambient to 800 °C.
1.2 The absence of reaction or decomposition is used as an indication of thermal stability in this test method under the experimental conditions used.
1.3 This test method may be performed on solids or liquids, which do not sublime or vaporize in the temperature range of interest.
1.4 This test method shall not be used by itself to establish a safe operating or storage temperature. It may be used in conjunction with other test methods (for example, Test Methods E487 and E537, and Guide E1981) as part of a hazard analysis of a material.
1.5 This test method is normally applicable to reaction or decomposition occurring in the range from room temperature to 800 °C. The temperature range may be extended depending on the instrumentation used.
1.6 This test method may be performed in an inert, a reactive or self-generated atmosphere.
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
IEC 61340-4-7:2017 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers). This document establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and decay (charge neutralization) time for ionizers. This document does not include measurements of electromagnetic interference (EMI), or the use of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices. As contained in this document, the test methods and test conditions can be used by manufacturers of ionizers to provide performance data describing their products. Users of ionizers are urged to modify the test methods and test conditions for their specific application in order to qualify ionizers for use, or to make periodic verifications of ionizer performance. The user will decide the extent of the data required for each application. This edition includes the following significant technical changes with respect to the previous edition: - the use of contacting plate voltage measurements in addition to the previous non-contacting plate voltage measurements has been added. Charged plate monitors (CPMs) using this technology have been in use in the industry for many years.
- Standard33 pagesEnglish languagee-Library read for1 day
Applies to activities that: manufacture, process, assemble, install, package, label, service, test, inspect, transport or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges greater than or equal to 100 V human body model (HBM). Provides the requirements for an ESD control program. The user should refer to IEC 61340-5-2 for guidance on the implementation of this standard. Does not apply to electrically initiated explosive devices, flammable liquids, gases and powders. The purpose of this standard is to provide the administrative and technical requirements for establishing, implementing and maintaining an ESD control program (hereinafter referred to as the 'program'). The main changes with respect to the previous edition are listed below: This version of IEC 61340-5-1 focuses on the requirements for an ESD control program. In addition, this version of IEC 61340-5-1 has been aligned with other major ESD control program standards used throughout the world.
- Standard23 pagesEnglish languagee-Library read for1 day
IEC 61340-4-9:2016 provides test methods for evaluating the electrical resistance of garments that contain surface conductive or dissipative components or materials used in the electronics industry for the control of electrostatic discharge. This standard defines procedures for measuring electrical resistance, including a system resistance test for garments that provide a ground path for personnel. This edition includes the following significant technical changes with respect to the previous edition: a) classification of three types of garments - static control garments, - groundable static control garments, and - groundable static control garment system; b) additional measurements according to the the garment type including cuff measurements, panel to groundable point, testing with a person in the garment system; c) sleeve to sleeve measurements allowed with probes or by hanging; d) additional recommended values for new garment types as set out in Annex A.
- Standard26 pagesEnglish languagee-Library read for1 day
IEC 60455-2:2015(E) specifies methods of test to be used for testing resin based reactive compounds, their components and cured compounds used for electrical insulation. This third edition cancels and replaces the second edition published in 1998. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Introduction of test methods related to IEC 60455-3-8; - Additional and updated test methods for resins. Keywords: resin based reactive compounds used for electrical insulation
- Standard42 pagesEnglish languagee-Library read for1 day
IEC 61340-4-8:2014 provides a test method for evaluating the performance of electrostatic discharge shielding bags tested according to the requirements of IEC 61340-5-3. The design voltage for the test apparatus is 1 000 V d.c. The test method presented in this standard can also be applied to packaging other than shielding bags. The purpose of this standard is to ensure that testing laboratories who use this test method to evaluate a given packaging material will obtain similar results. This standard does not address protection from electromagnetic interference (EMI), radio frequency interference (RFI), electromagnetic pulsing (EMP) nor protection against volatile materials. This edition includes the following significant technical changes with respect to the previous edition: a) modification to the title to include the word "Electrostatic" before discharge shielding"; b) removal of normative references ANSI/ESD STM5.1 and ASTM D-257-78 and replaced by normative references IEC 61340-3-1 and IEC 60093; c) new normative reference to IEC 61340-5-3 added, because the requirement for shielding bags have been included in this standard; d) imperial units have been removed.
- Standard16 pagesEnglish languagee-Library read for1 day
- Corrigendum3 pagesFrench languagee-Library read for1 day
IEC 61340-4-7:2017 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers).
This document establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and decay (charge neutralization) time for ionizers. This document does not include measurements of electromagnetic interference (EMI), or the use of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices. As contained in this document, the test methods and test conditions can be used by manufacturers of ionizers to provide performance data describing their products. Users of ionizers are urged to modify the test methods and test conditions for their specific application in order to qualify ionizers for use, or to make periodic verifications of ionizer performance. The user will decide the extent of the data required for each application. This edition includes the following significant technical changes with respect to the previous edition:
- the use of contacting plate voltage measurements in addition to the previous non-contacting plate voltage measurements has been added. Charged plate monitors (CPMs) using this technology have been in use in the industry for many years.
- Standard62 pagesEnglish and French languagesale 15% off
IEC 61340-4-9:2016 provides test methods for evaluating the electrical resistance of garments that contain surface conductive or dissipative components or materials used in the electronics industry for the control of electrostatic discharge. This standard defines procedures for measuring electrical resistance, including a system resistance test for garments that provide a ground path for personnel. This edition includes the following significant technical changes with respect to the previous edition:
a) classification of three types of garments
- static control garments,
- groundable static control garments, and
- groundable static control garment system;
b) additional measurements according to the the garment type including cuff measurements, panel to groundable point, testing with a person in the garment system;
c) sleeve to sleeve measurements allowed with probes or by hanging;
d) additional recommended values for new garment types as set out in Annex A.
- Standard45 pagesEnglish and French languagesale 15% off
IEC 61340-4-6:2015 provides electrical and mechanical test methods and performance limits for evaluation, acceptance and periodic verification testing of wrist straps. This standard is intended for testing wrist straps and wrist strap systems used for the grounding of personnel engaged in working with ESD sensitive assemblies and devices. It does not address constant monitoring systems. This edition includes the following significant technical changes with respect to the previous edition:
a) editorial comments made during the review of the first edition were reviewed and incorporated where appropriate;
b) several changes were made to update the Figures and improve the presentation of metric measurements (Imperial measurements have been removed);
c) the option of using an integrated checker for wrist strap system continuity testing has been added;
d) the evaluation and acceptance limit for wrist strap resistance has been changed so as to harmonize with IEC 61340-5-1.
- Standard38 pagesEnglish and French languagesale 15% off
IEC 61340-4-8:2014 provides a test method for evaluating the performance of electrostatic discharge shielding bags tested according to the requirements of IEC 61340-5-3. The design voltage for the test apparatus is 1 000 V d.c. The test method presented in this standard can also be applied to packaging other than shielding bags. The purpose of this standard is to ensure that testing laboratories who use this test method to evaluate a given packaging material will obtain similar results. This standard does not address protection from electromagnetic interference (EMI), radio frequency interference (RFI), electromagnetic pulsing (EMP) nor protection against volatile materials. This edition includes the following significant technical changes with respect to the previous edition:
a) modification to the title to include the word "Electrostatic" before discharge shielding";
b) removal of normative references ANSI/ESD STM5.1 and ASTM D-257-78 and replaced by normative references IEC 61340-3-1 and IEC 60093;
c) new normative reference to IEC 61340-5-3 added, because the requirement for shielding bags have been included in this standard;
d) imperial units have been removed.
- Standard25 pagesEnglish and French languagesale 15% off
IEC 61340-4-7:2010 provides test methods and procedures for evaluating and selecting air ionization equipment and systems (ionizers). This standard establishes measurement techniques, under specified conditions, to determine offset voltage (ion balance) and discharge (charge neutralization) time for ionizers. This standard does not include measurements of electromagnetic interference (EMI), or uses of ionizers in connection with ordnance, flammables, explosive items or electrically initiated explosive devices.
- Standard30 pagesEnglish languagesale 15% off
- Standard62 pagesEnglish and French languagesale 15% off
IEC 61340-4-6:2010 provides electrical and mechanical test methods and performance limits for evaluation, acceptance and functional testing of wrist straps. This standard is intended for testing wrist straps and wrist strap systems used for the grounding of personnel engaged in working with ESD sensitive assemblies and devices. It does not address constant monitoring systems.
- Standard19 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 61340-4-8:2010 provides a test method for evaluating the performance of electrostatic discharge shielding bags. The design voltage for the test apparatus is 1 000 V. The purpose of this standard is to ensure that testing laboratories who use this test method to evaluate a given packaging material will obtain similar results.
- Standard13 pagesEnglish languagesale 15% off
- Standard25 pagesEnglish and French languagesale 15% off
IEC 61340-4-9:2010 provides specific test methods for evaluating electrical resistance of static control garments. This part defines the test methods for determining the electrical resistance from sleeve-to-sleeve and point-to-point of static control garments. The test methods defined in this standard utilize standard instruments to measure the resistance of static control garments. These methods are intended as qualification test procedures. They can also be used as periodic tests to ensure ongoing electrical integrity of the garment under ambient conditions.
- Standard11 pagesEnglish languagesale 15% off
- Standard21 pagesEnglish and French languagesale 15% off
ISO 13916:2017 specifies requirements for the measurement of preheating temperature, interpass temperature and preheat maintenance temperature for fusion welding. ISO 13916:2017 can also be applied as appropriate in the case of other welding processes. ISO 13916:2017 does not cover the measurement of post weld heat treatment temperatures.
- Standard11 pagesEnglish languagee-Library read for1 day