CLC/TC 111X - Environment

This part of IEC 62321 specifies two different techniques for the determination of TCEP tris(2-chloroethyl) phosphate (TCEP) in plastics, the GC-MS or LC-MS method; both of which are suitable for quantitative analysis. These two techniques have been evaluated for use with polyurethane, Polyvinyl chloride and polyethylene materials containing TCEP between 200 mg/kg to 2 000 mg/kg. Use of the methods escribed in International Standard for other polymers and concentration ranges has not been specifically evaluated. These test methods do not apply to plastics materials having a processing temperature higher than 230 ℃. NOTE TCEP starts thermal decomposition at approximately 230 ℃. Polymer types which have a processing temperature into shapes of plastics (e.g. pellets, moulded parts, or sheets etc.) not exceeding the decomposition temperature can contain TCEP. Py-TD-GC-MS is another technique, suitable for the screening of TCEP in plastics (See Annex A).

IEC 62321-3-4:2023 specifies procedures for the screening of di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) in polymers of electrotechnical products by using high performance liquid chromatography with ultraviolet detector (HPLC-UV), thin layer chromatography (TLC) and thermal desorption mass spectrometry (TD-MS). High performance liquid chromatography with ultraviolet detector (HPLC-UV), thin layer chromatography (TLC) and thermal desorption mass spectrometry (TD-MS) techniques are described in the normative part of this document. Fourier transform infrared spectroscopy (FT-IR) is described in the informative annexes of this document.

IEC 62321-12:2023 specifies a reference test method for the simultaneous determination of polybrominated biphenyls, polybrominated diphenyl ethers, and four phthalates: di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) in polymers of electrotechnical products. The extraction technique described in this document is the ultrasonic-assisted extraction used for simultaneous extraction for sample preparation. Gas chromatography-mass spectrometry (GC-MS) is considered as the reference technique for the measurement of the simultaneous determination of analytes in the range of 25 mg/kg to 2 000 mg/kg. The test method using ultrasonic-assisted extraction followed by GC-MS detection has been evaluated by the tests of polypropylene (PP), polyvinylchloride (PVC), acrylonitrile butadiene styrene (ABS), acrylate rubber (ACM), polystyrene (PS), polyurethane (PU) and polyethylene (PE) materials. This document has the status of a horizontal publication in accordance with IEC Guide 108.

This document is applicable to the processes relating to the preparing for re-use of WEEE. NOTE 1 This document covers the preparing for re-use of WEEE arising from electrical and electronic equipment as listed in Annex I and Annex III of Directive 2012/19/EU. This document is applicable to preparing for re-use operators only and does not cover activities connected with used or second-hand equipment that have not become waste. It applies to all preparing for re-use operators, no matter their size or main focus of activity. This document assists in quantifying re-use, recycling and recovery rates in conjunction with EN 50625 1. In case of treatment operations (including the collection and logistics of WEEE) other than preparing for re-use, the EN 50625 series applies. Preparing for re-use processes includes the removal of whole components or parts where they are intended to either be used in the repair of faulty equipment or sold as re-use parts. The following EEE are not in the scope of this document: - industrial monitoring and control instruments; - in vitro diagnostic medical devices, medical devices or active implantable devices. NOTE 2 Examples of industrial monitoring and control instruments include equipment intended for use in potentially explosive atmospheres, and monitoring and control equipment that performs a safety function as part of industrial control system. NOTE 3 in vitro diagnostic medical devices, medical devices and active implantable devices have the capacity to collect and harbour pathogens, depending on the environment in which they operated. It is essential to follow clinically proven means for decontamination. Relevant Directives are 93/42/EEC and 98/79/EC.

IEC 62430:2019 describes principles, specifies requirements and provides guidance for organizations intending to integrate environmental aspects into the design and development in order to minimize the adverse environmental impacts of their products. This document applies to processes on how ECD (environmentally conscious design) are integrated into the design and development. This document applies to any organization, regardless of its size, type or sector. This document does not provide requirements for assessing the conformity of individual products. This horizontal standard is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 108. One of the responsibilities of a technical committee is, wherever applicable, to make use of horizontal standards in the preparation of its publications. The contents of this horizontal standard will not apply unless specifically referred to or included in the relevant publications. IEC 62430:2019 cancels and replaces the first edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Scope is extended from electrotechnical product and systems to all products including services. b) As a consequence of the scope expansion, non-electrotechnical products, services in particular, are taken into account to modify requirements. c) Clause 6 is added as a guidance.

This document defines product category rules (PCR) for electronic and electrical products and systems (EEPS).
It specifies the process and requirements on how to conduct life cycle assessment in the context of
environmental declarations.
PCR is complemented by additional product-specific rules (PSR), which further define e.g. functional units and
default scenarios in the product-specific context. Therefore, it also provides guidance on how to develop PSR
in corresponding technical committees.
This document provides common rules for:
a) life cycle assessment (LCA), including the requirements for developing default scenarios;
b) the LCA report;
c) the development of product specific rules.
This document provides further guidelines for environmental declarations.
The basic LCA principles and framework are based on the EN ISO 14040 series of standards (i.e EN ISO 14040
and ISO 14044), and therefore out of scope of the standard.

This document specifies a marking — of electrical and electronic equipment (EEE) with a view to minimizing the disposal of waste EEE (WEEE) as unsorted waste and to facilitating its separate collection. NOTE 1 This is in accordance with Article 14(4) of Directive 2012/19/EU (WEEE, recast) — that serves to clearly identify the producer of the equipment and — that the equipment has been put on the market after 13 August 2005. NOTE 2 This is in accordance with Articles 12(3) and 15(2) of Directive 2012/19/EU (WEEE, recast) — that applies to categories of electrical and electronic equipment subject to WEEE collection, treatment, recovery and environmentally sound disposal as defined by European and national regulations, provided the equipment concerned is not part of another type of equipment that does not fall within the scope of above mentioned regulations. NOTE 3 This is in accordance with Article 2 and Annexes I – IV of Directive 2012/19/EU (WEEE, recast) [1] The definition of a technical carrier medium for machine based identifying the producer, such as a barcode, electronic data medium or microchip, is not covered by this document.

This document specifies the procedure, content, and form relating to material declarations for products and accessories of organizations operating in and supplying to the electrotechnical industry. Process chemicals, emissions during product use and product packaging material are not in the scope of this document. The main intended use of this document is to provide data up and down the supply chain that: - allows organizations to assess products against substance compliance requirements, - allows organizations to use this information in their environmentally conscious design process and across all product life cycle phases. This document specifies mandatory declaration requirements and also provides optional declaration requirements. This document does not suggest any specific method or process to capture material declaration data in the supply chain. However, it provides a data format used to transfer information within the supply chain. Organizations have the flexibility to determine the most appropriate method to capture material declaration data without compromising data utility and quality. This document is intended to allow reporting based on engineering judgement, supplier material declarations, and/or sampling and testing.

This part of IEC 62321 specifies the screening analysis of polybrominated biphenyls (PBBs), polybrominated diphenyl ethers (PBDEs), di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP), di-n-octyl phthalate (DNOP), di-isononyl phthalate (DINP), and di-isodecyl phthalate (DIDP) in polymers of electrotechnical products using the analytical technique of gas chromatography-mass spectrometry using a pyrolyser/thermal desorption accessory (Py/TD-GC-MS). This test method has been evaluated through the analysis of PP (polypropylene), PS (polystyrene), and PVC (polyvinyl chloride) materials containing deca-BDE between 100 mg/kg and 1 000 mg/kg and individual phthalates between 100 mg/kg to 4 000 mg/kg as depicted in Annex J. Use of the methods described in this document for other polymer types, PBBs (mono-deca), PBDEs (mono-deca) and phthalates or concentration ranges other than those specified above has not been specifically evaluated. This document has the status of a horizontal standard in accordance with IEC Guide 108 [1]1.

This part of IEC 62321 specifies two techniques for the determination of hexabromocyclododecane (HBCDD) in polymers of electrotechnical products. The gas chromatography-mass spectrometry (GC-MS) test method is described in the normative part of this document. The GC-MS method is suitable for the determination of hexabromocyclododecane (HBCDD). A method using high-pressure liquid chromatography-mass spectrometry (HPLC-MS) is given in informative Annex A. These test methods have been evaluated for use with EPS (expanded polystyrene foam), XPS (extruded polystyrene foam) and ABS (acrylonitrile butadiene styrene) within the concentration ranges as specified in Table 1. The use of this method for other types of materials or concentration ranges outside those specified below has not been evaluated. [Table 1] This document has the status of a horizontal standard in accordance with IEC Guide 108.

This part of IEC 62321 provides strategies of sampling along with the mechanical preparation of samples from electrotechnical products. These samples can be used for analytical testing to determine the levels of certain substances as described in the test methods in other parts of the IEC 62321 series. Restrictions for substances will vary between geographic regions and can be updated on a regular basis. This document describes a generic process for obtaining and preparing samples prior to the determination of any substance of concern. This document does not provide: - full guidance on each and every product that could be classified as electrotechnical product. Since there is a huge variety of electrotechnical parts, with various structures and compositions, along with the continuous innovations in the industry, it is unrealistic to attempt to provide procedures for the disjointment of every type of part; - guidance regarding other routes to gather additional information on certain substances in a product, although the information collected has relevance to the sampling strategies in this document; - safe disassembly and mechanical disjointment instructions related to electrotechnical products (e.g. mercury-containing switches) and the recycling industry (e.g. how to handle CRTs or the safe removal of batteries). See IEC 62554 [1] 1 for the disjointment and mechanical sample preparation of mercury-containing fluorescent lamps; - sampling procedures for packaging and packaging materials; - analytical procedures to measure the levels of certain substances. This is covered by other standards (e.g. other parts of the IEC 62321 series), which are referred to as "test standards" in this document; - guidelines for assessment of compliance. This document has the status of a horizontal standard in accordance with IEC Guide 108 [2].

This clause of part 1 is replaced with the following: This European Standard is applicable to the treatment of photovoltaic panels as mentioned in the WEEE Directive under Annex 4. The scope of this document is limited to photovoltaic panels with a minimum surface area of 0,2 m2. This European Standard applies to the treatment of photovoltaic panels until end-of-waste status is fulfilled, or photovoltaic panel fractions are recycled, recovered or disposed. This European Standard addresses all operators involved in the treatment including related handling, sorting and storage of photovoltaic panels. This European Standard applies to all facilities including those whose treatment operations using mobile treatment installation.

This European Standard is applicable to the treatment of waste temperature exchange equipment and other WEEE containing VFC or VHC in refrigerants or blowing agents. This European Standard applies to the treatment of temperature exchange equipment until end-of-waste status is fulfilled, or temperature exchange equipment fractions are recycled, recovered, or disposed of. This European Standard addresses all operators involved in the treatment including related handling, sorting and storage of temperature exchange equipment.

IEC 62321-7-2:2017 describes procedures to measure hexavalent chromium, Cr(VI), quantitatively in samples of polymers and electronics. This method employs organic solvent to dissolve or swell the sample matrix, followed by an alkaline digestion procedure to extract Cr(VI) from samples. Studies have shown that organic/alkaline solution is more effective than acidic solution in extracting Cr(VI) from soluble and insoluble samples. Minimal reduction of Cr(VI) to Cr(III) or oxidation of Cr(III) to Cr(VI) occurs under alkaline conditions. The first edition of IEC 62321:2008 was a ‘stand-alone’ standard that included an introduction, an overview of test methods, a mechanical sample preparation as well as various test method clauses. This first edition of IEC 62321-7-2 is a partial replacement of IEC 62321:2008, forming a structural revision and generally replacing Annex C. IEC 62321-7-2 is the final replacement part of the corresponding clauses in IEC 62321:2008.

IEC 62321-8:2017 specifies two normative and two informative techniques for the determination of di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP), di-n-octyl phthalate (DNOP), di-isononyl phthalate (DINP) and di-iso-decyl phthalate (DIDP) in polymers of electrotechnical products.

IEC 63000:2016 specifies the technical documentation that the manufacturer compiles in order to declare compliance with the applicable substance restrictions

IEC 62321-7-1:2015 describes a boiling water extraction procedure intended to provide a qualitative determination of the presence of hexavalent chromium (Cr(VI)) in colourless and coloured corrosion-protection coatings on metallic samples. In this procedure, when Cr(VI) in a sample is detected below the 0,10 g/cm2 LOQ (limit of quantification), the sample is considered to be negative for Cr(VI). Since Cr(VI) may not be uniformly distributed in the coating even within the same sample batch, a "grey zone" between 0,10 g/cm2 and 0,13 g/cm2 has been established as "inconclusive" to reduce inconsistent results due to unavoidable coating variations. In this case, additional testing may be necessary to confirm the presence of Cr(VI). When Cr(VI) is detected above 0,13 g/cm2, the sample is considered to be positive for the presence of Cr(VI) in the coating layer.

This Technical Report provides information on the alignment between Directive 2012/19/EU and EN 50625 series standards and EN 50614.

IEC 62321-6:2015 specifies one normative and two informative techniques for the determination of polybrominated biphenyls (PBB) and diphenyl ethers (PBDE) in polymers of electrotechnical products. The test methods are: - The gas chromatography-mass spectrometry (GC-MS); - The ion attachment mass spectrometry (IAMS) technique and - The high-pressure liquid chromatography technique. This first edition of IEC 62321-6 is a partial replacement of IEC 62321:2008, forming a structural revision and generally replacing Annex A.

This clause of Part 1 is replaced by the following: This European standard is applicable to the treatments of WEEE containing CRTs and flat panel displays. This European standard applies to the treatment of WEEE containing CRTs and flat panel displays until end-of-waste status is fulfilled, or fractions are recycled, recovered, or disposed of. This European standard addresses all operators involved in the treatment including related handling, sorting, and storage.

Clause 1 is replaced with the following: This European Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard for photovoltaic panels, FprEN 50625-2-4 and Technical Specification for de-pollution - General CLC/TS 50625-3-1:2015.

This clause of Part 1 is replaced by the following: This European standard is applicable to the treatment of lamps. This European Standard applies to the treatment of lamps until end-of-waste status is ful-filled, or lamp fractions are recycled, recovered, or disposed of. This European Standard addresses all operators involved in the treatment including related handling, sorting, and storage of lamps. This European Standard applies to all facilities including those whose treatment operations use mobile equipment.

Clause 1 of CLC/TS 50625-3-1:2015 is replaced with the following: This European Technical Specification is intended to be used in conjunction with CLC/TS 50625-3-1 Collection, logistics and treatment requirements for WEEE - Part 1: General treatment requirements, EN 50625 1, Collection, logistics and Treatment requirements for WEEE - Part 2-2: Treatment requirements for WEEE containing CRTs and flat panel displays, EN 50625-2-2 and Collection, logistics and treatment requirements for WEEE - Part 3-1: Specification for de-pollution - General, CLC/TS 50625-3-1.

This Technical Specification addresses the processes regarding the recycling of copper and/or precious metals contained in WEEE and fractions of WEEE. NOTE 1 For the treatment of WEEE EN 50625-1 applies. This Technical Specification relates to the chemical and metallurgical processes used for the recycling of copper and/or precious metals contained in WEEE and fractions of WEEE, thereby differentiating it from manual/mechanical processing (see Annex A). All chemical and metallurgical processes are included up and until the output materials will be used for their original purpose or for other purposes or will be finally disposed of. NOTE 2 The main precious metals concerned are gold, silver, and palladium. NOTE 3 The majority of the WEEE volumes that are processed by final treatment operators consists of fractions of WEEE (e.g. circuit boards) containing copper and/or precious metals, however there may be whole small WEEE that can be treated directly in final treatment (e.g. USB sticks). NOTE 4 Chemical and metallurgical processes are processes in which a chemical reaction takes place for example: pyrolysis, smelting, refining, solvent extraction, ion exchange, leaching/dissolution in water acids or base, precipitation, cementation, pressure leaching. They differ from mechanical / physical processes such as sorting and separation based on physical properties (e.g. density, magnetism, colour) and size reduction processes such as shredding and grinding. NOTE 5 In general, these final treatment facilities are covered by the IED 2010/75/EU, e.g. copper smelters or refiners.

This Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard for temperature exchange equipment, EN 50625-2-3, and the Technical Specification for de-pollution, CLC/TS 50625 3-1.

This Technical Specification applies to the following operations: collection, handling, sorting, storage, preparation for transport and transport of WEEE. It is applicable to all WEEE prior to arriving at the treatment facility or arriving at a preparation for re-use facility. This Technical Specification addresses all operators that perform collection and logistics operations. This technical specification does not cover treatment of WEEE. In case of treatment activities undertaken at collection or logistics facilities the Standard EN 50625-1 applies.

This European Standard is applicable to the treatment of waste electrical and electronic equipment (WEEE). This standard will be supplemented, for example by standards covering specific equipment. NOTE This European Standard is intended to cover WEEE arising from electrical and electronic equipment as listed in Annex I and Annex III of Directive 2012/19/EU. This standard applies to the treatment of WEEE until end-of-waste status is fulfilled, or until the WEEE is prepared for re-use, recycled, recovered, or disposed of. This standard addresses all operators involved in the treatment including related handling, sorting, and storage of WEEE.

IEC 62321-4:2013 describes the use of four test methods for mercury in polymers, metals and electronics, namely CV-AAS (cold vapour atomic absorption spectrometry), CV-AFS (cold vapour atomic fluorescence spectrometry) ICP-OES (inductively coupled plasma optical emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry) as well as several procedures for preparing the sample solution from which the most appropriate method of analysis can be selected by experts.

IEC 62321-3-2:2013 specifies the screening analysis of the total bromine (Br) in homogeneous materials found in polymers and electronics by using the analytical technique of combustion ion chromatography (C-IC).

IEC 62321-5:2013 describes the four test methods for lead, cadmium and chromium in polymers, metals and electronics, namely AAS (atomic absorption spectrometry), AFS (atomic fluorescence spectrometry), ICP-OES (inductively coupled plasma optical emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry) as well as several procedures for preparing the sample solution from which the most appropriate method of analysis can be selected by experts.

IEC 62321-3-1:2013 describes the screening analysis of five substances, specifically lead (Pb), mercury (Hg), cadmium (Cd), total chromium (Cr) and total bromine (Br) in uniform materials found in electrotechnical products, using the analytical technique of X-ray fluorescence (XRF) spectrometry.

IEC 62542:2013 specifies generic terms and definitions that are related to environmental standardization within the IEC. It serves as a glossary of terminology to be considered for environmental aspects of relevant work in IEC. The terms cover environmental issues that are relevant for electrotechnical products across all product life cycle stages. It has the status of a horizontal standard in accordance with IEC Guide 108.

IEC 62321-1:2013 refers to the sample as the object to be processed and measured. The nature of the sample and the manner in which it is acquired is defined by the entity carrying out the tests and not by this standard. It provides guidance on the disassembly procedure employed for obtaining a sample. This first edition of IEC 62321-1 is a partial replacement of IEC 62321, forming a structural revision and replacing Clauses 1 to 4.

This European Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard for lamps, EN 50625-2-1, and the Technical Specification CLC/TS 50625-3-1:2014 for de-pollution - General.

This Technical Specification is intended to be used in conjunction with the WEEE Treatment Standard EN 50625-1 for most types of WEEE (other documents will be developed to define requirements for specific WEEE requiring more specialised treatment).

This European Standard specifies a marking • of electrical and electronic equipment in accordance with Article 11(2) of Directive 2002/96/EC (WEEE); NOTE This is in addition to the marking requirement in Article 10(3) of this Directive which requires producers to mark electrical and electronic equipment put on the market after 13 August 2005 with a ‘crossed-out wheeled bin’ symbol. • that applies to electrical and electronic equipment falling under Annex IA of Directive 2002/96/EC, provided the equipment concerned is not part of another type of equipment that does not fall within the scope of this Directive. Annex IB of Directive 2002/96/EC contains an indicative list of the products, which fall under the categories set out in Annex IA of this Directive; • that serves to clearly identify the producer of the equipment and that the equipment has been put on the market after 13 August 2005. The definition of a technical carrier medium for identifying the producer, such as a barcode, electronic data medium or microchip, is not covered by this standard.

IEC 62321-2:2013 provides strategies of sampling along with the mechanical preparation of samples from electrotechnical products, electronic assemblies and electronic components. These samples can be used for analytical testing to determine the levels of certain substances as described in the test methods in other parts of IEC 62321. Restrictions for substances will vary between geographic regions and from time to time. This Standard describes a generic process for obtaining and preparing samples prior to the determination of any substance which are under concern.

This European Standard specifies the technical documentation that the manufacturer needs to compile in order to declare compliance with the applicable substance restrictions. The documentation of the manufacturer’s management system is outside the scope of this European Standard.

IEC 62474:2012 specifies the procedure, content, and form relating to material declarations for products of companies operating in and supplying the electrotechnical industry. Process chemicals and emissions during product use are not in the scope of this International Standard. It provides data to downstream manufacturers that: - allows them to assess products against substance restriction compliance requirements; - they can use in their environmentally conscious design process and across all product life cycle phases. A database associated with this document is available at: http://std.iec.ch/iec62474. It contains the list of: - Declarable substance groups and declarable substances; - Reference Substances; - Material classes; - XML schema for data format and exchange and the accompanying developer table.

2014-12-12: Corrigendum to rename EN 50574:2012 into EN 50574-1:2012.

EN 50574:2012 gives the responsible take-back parties the task of defining target values. This Technical Specification provides applicable target values, characteristic numbers; sampling and analysis procedures, as well as monitoring and reporting requirements. Furthermore, this Technical Specification provides validation methodologies for tests and the daily business of the treatment plants as defined in EN 50574:2012.

This European Standard defines requirements for the end of life handling, transportation, storage, sorting and treatment of WEEE household appliances containing volatile fluorocarbons, volatile hydrocarbons, or both. Furthermore, this standard only applies to WEEE household appliances that use heat-transfer media other than water e.g. refrigerators, freezers, heat pump tumble dryers, de-humidifiers and portable air conditioners. Discarded appliances covered by this standard will have been deposited at a collection facility as domestic WEEE.
The European Standard describes requirements for the removal of volatile fluorocarbons and volatile hydrocarbons. These substances can be found as refrigerant in the refrigerating system (partly dissolved in the oil) and as blowing agent in the insulation foam of discarded household appliances.
NOTE    This standard has been prepared to fulfil the requirements of Directive 2002/96/EC but does not preclude the procedures described herein from being used to treat appliances that are not commonly found in private households.
It defines requirements pertaining to producers, WEEE compliance schemes (acting on behalf of producers) and waste treatment facilities so as to ensure the provisions of applicable national laws resulting from European legislation are fulfilled. These requirements are intended to define procedures, parameters based on the best available technologies at the time of the publication; however, provisions laid down by national regulatory bodies will continue to additionally apply. This standard only describes the results to be achieved, it does not specify how they are to be achieved nor does it prescribe the use of any specific technology.
This European Standard does not generally cover collection facilities, nor does it cover how appliances arrive at these facilities. However, this standard does address the sorting of heat-pump tumble dryers from other types of tumble dryer, a task that could be performed at a collection facility.
This European Standard defines requirements relating to handling, transportation, sorting and treatment of WEEE covered by the scope of this standard. This standard does not include any activity prior to delivery to a logistic facility.

This European Standard defines requirements for the end of life handling, transportation, storage, sorting and treatment of WEEE household appliances containing volatile fluorocarbons, volatile hydrocarbons, or both. Furthermore, this standard only applies to WEEE household appliances that use heat-transfer media other than water e.g. refrigerators, freezers, heat pump tumble dryers, de-humidifiers and portable air conditioners. Discarded appliances covered by this standard will have been deposited at a collection facility as domestic WEEE. The European Standard describes requirements for the removal of volatile fluorocarbons and volatile hydrocarbons. These substances can be found as refrigerant in the refrigerating system (partly dissolved in the oil) and as blowing agent in the insulation foam of discarded household appliances. NOTE This standard has been prepared to fulfil the requirements of Directive 2002/96/EC but does not preclude the procedures described herein from being used to treat appliances that are not commonly found in private households. It defines requirements pertaining to producers, WEEE compliance schemes (acting on behalf of producers) and waste treatment facilities so as to ensure the provisions of applicable national laws resulting from European legislation are fulfilled. These requirements are intended to define procedures, parameters based on the best available technologies at the time of the publication; however, provisions laid down by national regulatory bodies will continue to additionally apply. This standard only describes the results to be achieved, it does not specify how they are to be achieved nor does it prescribe the use of any specific technology. This European Standard does not generally cover collection facilities, nor does it cover how appliances arrive at these facilities. However, this standard does address the sorting of heat-pump tumble dryers from other types of tumble dryer, a task that could be performed at a collection facility. This European Standard defines requirements relating to handling, transportation, sorting and treatment of WEEE covered by the scope of this standard. This standard does not include any activity prior to delivery to a logistic facility.

IEC 62430:2009 specifies requirements and procedures to integrate environmental aspects into design and development processes of electrical and electronic products, including combination of products, and the materials and components of which they are composed. It has the status of a horizontal standard in accordance with IEC Guide 108.