CEN/TC 162/WG 3 - Protective clothing against chemicals, infective agents and radioactive contamination
Standardization of specifications for resistance to chemicals of protective clothing.
Protective clothing against chemicals, infective agents and radioactive contamination
Standardization of specifications for resistance to chemicals of protective clothing.
General Information
This document specifies the test method for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity:
a) Method A: low-level spray test. This is applicable to clothing that covers the full body surface and is intended to be worn when there is a potential risk of exposure to small quantities of spray or accidental low-volume splashes of a liquid chemical.
b) Method B: high-level spray test. This is applicable to clothing with spray-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment, which covers the full body surface and which is intended to be worn when there is a risk of exposure to sprayed liquid chemical.
This document does not apply to chemical permeation resistance of the materials from which the chemical protective clothing is made.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard establishes minimum performance, classification, and labelling requirements
for protective clothing worn by operators handling liquid pesticide products as well as re-entry workers. Pesticide
handling includes application of diluted formulations, mixing and loading, and other activities such as cleaning
of contaminated equipment and containers. Protective clothing covered by this International Standard
includes, but is not limited to, shirts, jackets, trousers, coveralls, aprons, protective sleeves, caps/hats and
other headwear made with textile material, and material placed below knapsack/backpack sprayers. This
International Standard does not address items used for the protection of the respiratory tract, hands, and feet.
This International Standard does not address protection against biocides, fumigants or highly volatile liquids.
- Amendment11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements, test methods, marking and information supplied by the manufacturer, for ventilated and non-ventilated gas-tight chemical protective suits for use by emergency teams (ET).
It specifies full body personal protective ensembles to be worn for protection against solid, liquid and gaseous chemicals, including liquid and solid aerosols. Chemicals such as violently air sensitive reagents, unstable explosives and cryogenic liquids have not been considered since protection against these additional hazards is beyond the scope of this standard.
This document does not establish minimum criteria for protection against non-chemical hazards, e.g. radiological, fire, heat and explosive hazards and infective agents. This type of equipment is not intended for total immersion in liquids.
The seams, joins and assemblages attaching the accessories are included within the scope of this standard. The performance criteria for the accessories, gloves, boots or respiratory protective equipment are given in other standards.
Particulate protection is limited to physical penetration of the particulates only.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer for ventilated and non-ventilated gas-tight chemical protective suits.
It specifies full body personal protective ensembles to be worn for protection against solid, liquid and gaseous chemicals, including liquid and solid aerosols.
This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosive hazards, infective agents. This type of equipment is not intended for total immersion in liquids.
The seams, joins and assemblages attaching the accessories are included within the scope of this standard. The basic performance criteria for the components such as gloves, boots or respiratory protective equipment are given in other Standards, supplemantary requirements are provided in this standard.
Particulate protection is limited to physical penetration of the particulates only.
Chemicals such as violently air sensitive reagents, unstable explosives and cryogenic liquids have not been considered since protection against these additional hazards is beyond the scope of this standard.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a test method for the determination of the resistance of protective
clothing, gloves and footwear materials to permeation by potentially hazardous gaseous chemicals
under the condition of continuous contact.
This test method is applicable to the assessment of protection against gazeous chemicals that can be
collected only by liquid or gaseous collecting media.
!This test method is not applicable for the assessment of gaseous chemical mixtures."
This test method describes the modifications to EN 16523-1 necessary to test against gaseous chemicals
that can be collected by liquid or gaseous collecting media.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a test method for the determination of the resistance of protective clothing, gloves and footwear materials to permeation by potential hazardous liquid chemicals under the condition of continuous contact.
This test method is applicable to the assessment of protection against liquid chemicals that can be collected only by liquid or gaseous collecting media.
This test method is not adapted for the assessment of chemical mixtures, except for aqueous solutions.
This standard shall be used with the specifications given in the products standards (for examples EN 374 1 for gloves) where the following information shall be defined:
- any pre-conditioning;
- precise sampling (place, size, number);
- associated levels of performance.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and test methods for protective clothing, ventilated by an independent supply of air from an uncontaminated source, protecting the body and the respiratory system of the wearer against solid airborne particles including radioactive contamination. This kind of protective clothing can be provided with an emergency breathing facility.
This European Standard does not apply for the protection against ionizing radiation and the protection of patients against contamination with radioactive substances by diagnostic and/or therapeutic measures.
If additional protection against chemicals is required, reference should be made to the relevant standard and/or CEN/TR 15419.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 27065 establishes minimum performance, classification, and marking requirements for protective clothing worn by operators handling pesticide products as well as re-entry workers. For the purpose of ISO 27065, the term pesticide applies to insecticides, herbicides, fungicides, and other substances applied in liquid form that are intended to prevent, destroy, repel, or reduce any pest or weeds in agricultural settings, green spaces, roadsides, etc. It does not include biocidal products used for agricultural and non-agricultural settings.
Pesticide handling includes mixing and loading, application, and other activities such as cleaning contaminated equipment and containers. Concentrated pesticides are typically handled during mixing and loading. Protective clothing covered by ISO 27065includes, but is not limited to, shirts, jackets, trousers, coveralls, aprons, protective sleeves, caps/hats and other headwear (excluding hard hats made of rigid materials, e.g. hats worn by construction workers), and accessories used under knapsack/backpack sprayers.
ISO 27065 does not address items used for the protection of the respiratory tract, hands, and feet. ISO 27065 does not address protection against fumigants.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 19918 describes laboratory test methods to determine the resistance of materials, closures, and seams used in personal protective equipment (PPE) to permeation by solid or liquid chemicals with low vapour pressure (less than 133,322 Pa at 25 °C) and/or insolubility in water or other liquids commonly used as collection media. These chemicals that are often part of pesticide formulations and other mixtures cannot be measured using other standards for measuring permeation. This test method is suitable for field strength and concentrated pesticide formulations as well as other mixtures in which the active ingredient is a chemical with low vapour pressure and/or low solubility in commonly used liquid and gaseous collection media.
This test method is not intended to be used in place of standards such as ISO 6529, EN 16523-1 and ASTM F739, which measure permeation of chemicals that are either volatile or soluble in water or other liquids that do not interact with the material being tested. ISO 19918 is not suitable for measurement of volatile chemicals that may evaporate before the chemical analysis is complete.
The degree of contamination depends on numerous factors, such as type of exposure, application technique, and chemical formulation. As the level of exposure can vary considerably, this method is designed to rate relative performance of PPE materials for different durations.
This method is designed to measure cumulative permeation. Breakthrough time cannot be measured by this method. This test method does not measure resistance to penetration or degradation.
The test method standard may be used for the evaluation of PPE materials that are new or those for which the product standard requires treatment, such as laundering or simulated abrasion. Details of the treatment shall be reported.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Report is primarily intended for users, specifiers and others with responsibility for the procurement and provision of chemical protective clothing. It is also intended to be used by manufacturers in their dialogue with the users of PPE.
This Technical Report is intended to clarify the inter-relationship of the set of standards, developed by CEN/TC 162 WG 3, and to explain the main ideas behind these standards. This set of standards has been developed in support of the European legislation on PPE and is currently used as a major technical tool for the assessment and certification of CPC before it is put on the European market.
These guidelines are intended to assist users and specifiers in selecting the correct type of CPC for the task to be performed, and to help them ensure it is used according to the manufacturer's instructions to provide adequate protection during its entire lifetime. Lifetime and effectiveness of protective clothing depend largely on care and maintenance. When cleaning, disinfection and end-of-life disposal are considered the environmental impact should also be taken into account.
This Technical Report does not address chemical nuisance factors without potential impact on a person's health and safety, e.g. smell.
- Technical report48 pagesEnglish languagesale 10% offe-Library read for1 day
This part of ISO 13982 specifies the minimum requirements for chemical protective clothing resistant to penetration by airborne solid particles (type 5). These garments are full-body protective clothing, i.e. covering trunk, arms and legs, such as one-piece coveralls or two piece suits, with or without hood or visors, with or without foot protection. Requirements for component parts, such as hoods, gloves, boots, visors or respiratory protective equipment might be specified in other International and European Standards. This part of ISO 13982 is applicable only to airborne solid particulates. It is not applicable to other forms of challenge by solid chemicals, e.g. penetration of chemical dust through materials by rubbing or flexing, which may form the object of separate standards.
- Amendment8 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for the following types of limited use and reusable chemical protective clothing:
- Full-body protective clothing with liquid-tight connections between different parts of the clothing (Type 3: liquid-tight clothing) and, if applicable, with liquid-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards.
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;
- Full-body protective clothing with spray-tight connections between different parts of the clothing (Type 4: spray-tight clothing) and, if applicable, spray-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards.
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;
- Partial body protection garments offering protection to specific parts of the body against permeation of chemical liquids.
Examples of such garments are e.g. laboratory coats, jackets, trousers, aprons, sleeves, hoods (not air-supplied) etc. As partial body protection leaves some parts of the body unprotected this document specifies only the performance requirements for the clothing material and the seams.
NOTE Partial body chemical protective garments which offer only protection against penetration of chemical liquids are within the scope of EN 13034 (Type PB [6] clothing).
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the minimum requirements for limited use and re-useable limited performance chemical protective clothing. Limited performance chemical protective clothing is intended for use in cases of a potential exposure to a light spray, liquid aerosols or low pressure, low volume splashes, against which a complete liquid permeation barrier (at the molecular level) is not required.
This document covers both chemical protective suits (Type 6) and partial body protection (Type PB [6]).
Chemical protective suits (Type 6) cover and protect at least the trunk and the limbs, e.g. one-piece coveralls or two piece suits, with or without hood, boot-socks or boot-covers. This document specifies minimum requirements for the connections between different parts of Type 6 suits by the use of a reduced whole suit spray test using a variant of EN 468, as described in 5.2.
Partial body protection of similar limited performance (Type PB [6]) covers and protects only specific parts of the body, e.g. coats, aprons, sleeves etc. They should not be tested to the whole suit test (5.2).
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 17491-3:2008 specifies a test method for determining the resistance of protective clothing against penetration by a jet of liquid.
ISO 17491-3:2008 is applicable to clothing with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment worn with it.
ISO 17491-3:2008 does not address chemical permeation resistance of the clothing materials, which is specified in other standards.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a test method to determine the resistance of textile materials against penetration by atomized liquid chemicals, emulsions and dispersions. These materials are intended to be used in both limited-use and reusable protective clothing.
The penetration is expressed in percent, as ratio of the amounts of chemical applied and retained by the textile. The methods of quantitative physico-chemical analysis used for mass detection will depend on the chemical under test.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6530:2005 specifies a test method for the measurement of indices of penetration, absorption and repellency for protective clothing materials against liquid chemicals, mainly chemicals of low volatility.
Two levels of the potential performance of materials are assessed by this method of testing to meet with possible requirements for protection against the following:
deposition on the surface of a material, at minimal pressure, of spray droplets up to coalescence or occasional small drips;contamination by a single low-volume splash or low-pressure jet, allowing sufficient time to divest the clothing or take other action as necessary to eliminate any hazard to the wearer from chemical retained by the protective garment, or, in circumstances where pressure is applied to liquid contaminants on the surface of the clothing material as a result of natural movements of the wearer (flexing of contaminated areas of clothing at arms, knees, shoulders) and contact with contaminated surfaces (e.g. walking through sprayed foliage).
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 13982-2:2004 specifies a test method to determine the barrier efficiency of chemical protective clothing against aerosols of dry, fine dusts.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 13982-1:2004 specifies the minimum requirements for chemical protective clothing resistant to penetration by airborne solid particles (Type 5). These garments are full-body protective clothing, i.e. covering trunk, arms and legs, such as one-piece coveralls or two piece suits, with or without hood or visors, with or without foot protection. Requirements for component parts, such as hoods, gloves, boots, visors or respiratory protective equipment might be specified in other International and European Standards.
ISO 13982-1:2004 is applicable only to airborne solid particulates. It is not applicable to other forms of challenge by solid chemicals, e.g. penetration of chemical dust through materials by rubbing or flexing, which may form the object of separate standards.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Replace reference to ISO 139 by reference to EN 20139
- Corrigendum2 pagesEnglish, French and German languagesale 10% offe-Library read for1 day
This standard specifies requirements and test methods for re-usable and limited use protective clothing providing protection against infective agents. Clothing worn by surgical teams or drapes laid on patients to prevent cross-contamination during surgical interventions, are not covered by the scope of this standard.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and test methods for non-ventilated protective clothing protecting the wearer against particulate radioactive contamination. Such clothing is intended to protect only the body, arms and legs of the wearer, but it may be used with accessories which provide protection to additional areas of the wearer (e.g. boots, gloves, RPE). Protection to these other areas is specified in other European Standards.
This European Standard does not apply for the protection against ionizing radiation and the protection of patients against contamination with radioactive substances by diagnostic and/or therapeutic measures.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes a test method to assess the resistance of a gas-tight suit to the penetration of gases through, for example, essential openings, fastenings, seams, overlaps between items, pores and any imperfections in the materials of construction.
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and test methods for materials and seams of re-usable and single use protective clothing providing protection of the wearer against infective biological agents. Design criteria, mechanical requirements, and functional fit requirements are basd on either ISO 16602 series or by the ISO 20384 as indicated in this document, while the barrier properties of this document will be additive to ensure the protection against infective biological agents.
NOTE This standard is a standalone standard but using requirements based on ISO 16602 series and ISO 20384.
For products intended for the dual use as both a PPE and as a medical gown, both this document and the ISO 20384 shall apply.
Clothing worn by surgical teams or drapes laid on patients to prevent cross-contamination during surgical interventions are not covered by the scope of this document, but are covered solely by ISO 20384.
This document not applicable to components such as gloves, boots, eye/face protection devices and respiratory protective devices as their performance criteria are given in other standards. However, when these components are either an integral part of the protective clothing ensemble or are tested separately as partial body protection, supplementary requirements are provided in this standard. This document does not cover requirements for antimicrobial treatments for protective clothing.
- Draft49 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same minimum chemical protective barrier performance requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that other parts of ISO 16602 may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicates the intended use of the protective clothing. It is similarly important that the user (specifier) carries out a risk assessment in order to establish the correct protective performance levels for the intended task.
- Draft38 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum performance classification and labelling requirements for protective clothing designed to provide protection against:
- specified chemicals in the workplace, and
- unidentified chemicals in emergency situations.
Protective clothing against chemicals including solids, airborne particles, aerosols, liquids, and gases is addressed by this document.
Protective clothing items covered by this document include full body and partial body. The area of protection is denoted in the marking requirements. The ISO 16602 series allows for a modular approach.
This document sets the general requirements and the rules for applying the modular approach. The other parts focus on requirements and classification from design, chemical, physical properties and full garment testing perspectives. The seams, joins and assemblages attaching the components (including accessories) are included within the scope of this series of standards. ISO 16602-6 provides a Selection, Care and Maintenance guide to help the end-user selection process.
Chemicals such as violently air sensitive reagents, unstable explosives and cryogenic liquids have not been considered since protection against these additional hazards is beyond the scope of this standard.
Particulate protection is limited to physical penetration of the particulates only; permeation of solids is not considered.
This document does not address components such as gloves, boots, eye/face protection devices and respiratory protective devices as their performance criteria are given in other standards. However, when these components are an integral part of the protective clothing ensemble or are tested as part of an ensemble, supplementary requirements may be provided in this standard.
This document does not specifically address non-chemical hazards, such as biological and infective agents, thermal (flame, heat or cold) hazards, explosive hazards, and ionizing radiation hazards as specific requirements are covered by other relevant standards. The type of equipment specified in this series of standards is not intended for total immersion in liquids. However, additional protection may be integrated as a specific module based on the respective standard (e.g. meeting both ISO 16602-1 & ISO 11612 in a multi-risk suit).
It is not the intent of this series of documents to be exhaustive and address all situations.
- Draft46 pagesEnglish languagesale 10% offe-Library read for1 day
This document addresses the selection, use, care and maintenance (SUCAM) of chemical protective clothing (CPC). This guidance document is primarily intended for users, specifiers and others with responsibility for the procurement and provision of chemical protective clothing. It is also intended to be used by manufacturers in their dialogue with the users of PPE.
This guidance document is intended to clarify the inter-relationship between this ISO 16602 series of standards and its modular approach, ISO 17723-1 but also how this links to the old classification of CPC.
These guidelines are intended to assist users and specifiers in selecting the correct type of CPC for the task to be performed, and to help them ensure it is used according to the manufacturer's instructions to provide adequate chemical protection (including solids, airborne particles, aerosols, liquids, and gases (including radioactive contamination)) during its entire lifetime. Lifetime and effectiveness of protective clothing depend largely on care and maintenance. When cleaning, disinfection and end-of-life disposal are considered the environmental impact should also be taken into account.
To assist the users of products covered under this document, this document provides descriptions of referenced test methods, guidelines for conducting hazard and risk assessments and suggested performance levels for certain applications. It is not the intent of this document to address all situations.
NOTE Although this document has been created as a stand-alone document covering ISO 16602-1 through ISO 16602-5, it is strongly recommended to read this guidance in conjunction with ISO 16602-1 (if not the other parts) to understand the detail of the requirements.
- Draft105 pagesEnglish languagesale 10% offe-Library read for1 day
SO 16602:2007 establishes minimum performance classification and labelling requirements for protective clothing designed to provide protection against chemicals. Protective clothing items covered by ISO 16602:2007 include, but may not be limited to, totally encapsulating suits, liquid-tight or spray-tight suits, coveralls, jackets, trousers, aprons, smocks, hoods, sleeves, and shoe and boot covers.
Chemical protective clothing for protection against airborne particles is addressed by ISO 13982-1, which is referenced in ISO 16602:2007. ISO 16602:2007 does not address protection against solid chemicals in forms other than airborne solid particulates (e.g. it does not address the challenge of penetration of chemical dust and powders through materials and clothing by rubbing or flexing or by simple direct contact of dust or powders onto the clothing surface).
ISO 16602:2007 does not address gloves, boots, eye/face protection devices and respiratory protective devices unless they are an integral part of the protective clothing. ISO 16602:2007 does not address protection against biological or thermal (hot or cold) hazards, ionizing radiation, or radioactive contamination. ISO 16602:2007 also does not address the specialized clothing used in hazardous chemical emergencies.
ISO 16602:2007 is intended to provide chemical protective clothing manufacturers with minimum requirements for testing, classifying, and labelling chemical protective clothing. To assist the users of products covered under ISO 16602:2007, this document provides descriptions of referenced test methods, guidelines for conducting hazard and risk assessments and suggested performance levels for certain applications. It is not the intent of ISO 16602:2007 to address all situations.
- Draft39 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the chemical performance classification and test methods for materials used in
chemical protective clothing, including gloves and footwear. The gloves and boots should have the same
minimum chemical protective barrier requirements as the fabric when they are an integral part of the
clothing.
While these performance levels are intended to relate to the usage to which the chemical protective
clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate
the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in
order to establish the correct performance level for the intended task.
- Draft29 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 27065 establishes minimum performance, classification, and marking requirements for protective clothing worn by operators handling pesticide products as well as re-entry workers. For the purpose of ISO 27065, the term pesticide applies to insecticides, herbicides, fungicides, and other substances applied in liquid form that are intended to prevent, destroy, repel, or reduce any pest or weeds in agricultural settings, green spaces, roadsides, etc. It does not include biocidal products used for agricultural and non-agricultural settings.
Pesticide handling includes mixing and loading, application, and other activities such as cleaning contaminated equipment and containers. Concentrated pesticides are typically handled during mixing and loading. Protective clothing covered by ISO 27065includes, but is not limited to, shirts, jackets, trousers, coveralls, aprons, protective sleeves, caps/hats and other headwear (excluding hard hats made of rigid materials, e.g. hats worn by construction workers), and accessories used under knapsack/backpack sprayers.
ISO 27065 does not address items used for the protection of the respiratory tract, hands, and feet. ISO 27065 does not address protection against fumigants.
- Draft32 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer, for chemical protective suits for use by emergency teams (ET), including component parts such as gloves, bootees and boots which may be specified elsewhere. It describes personal protective ensembles to be worn during hazardous materials activities involving solid, liquid, gaseous and particulate hazards only. This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosive hazards. This type of equipment is not intended for total immersion in liquids. The seams, joins and assemblages attaching the accessories are included within the scope of this standard. The performance criteria for the accessories, gloves, boots or respiratory protective equipment are given in other European Standards.
- Draft18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer for the following ventilated and non-ventilated liquid-tight chemical protective suits.
Full body protective clothing with liquid-tight connections between different parts of the clothing (Type 3 liquid-tight clothing) and, with liquid-tight connections to component parts, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards. Examples of such clothing are one-piece coveralls or two piece suits, with or without hood or visor, with or without boot-socks or over-boots, with gloves attached liquid tight to the suit.
It describes personal protective ensembles for use by emergency teams, e.g. first responders or fire brigades, in situations where the chemical hazards are known. Type 3- ET suits are generally used during rescue operations, salvage work, cleanup and decontamination procedures, especially to protect against liquid and solid chemicals. Chemical protective clothing conforming to this standard is not designed to provide protection against gases and vapours, nor substances with a high vapour pressure.
Suits described in this standard have to completely cover the body. It is designed with liquid tight connections to suit socks, or booties and liquid tight gloves. They are not designed as respiratory protection, but they need to provide adequate liquid protection (Jet test) where joints to respiratory devices are required. Minimum performance classes for mechanical properties are defined.
This standard specifies special performance requirements for both the materials of construction of the chemi-cal protective suit and for the suit as a whole, including component parts, such as respiratory protective de-vices, gloves, boots, seams, joins and assemblages. This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosives etc. This type of equipment is not intended for total immersion in liquids. Chemical protective clothing conforming to this standard is not designed to provide protection against gases and vapours.
The basic performance criteria for the component parts: gloves, boots or respiratory protective equipment are given in other European Standards, (these Type 3-ET garments need to fulfil the requirements of the related product standards for gloves or boots etc, and the minimum requirements defined in this Standard). The chemical protection suits specified in this standard are designed to be used with respiratory protective devices.
- Draft19 pagesEnglish languagesale 10% offe-Library read for1 day
2012-07-23 GVN: draft for // vote received in ISO/CS (see e-mail of 2012-07-20 in dataservice).
2012-06-11 - IMPORTANT! When the notification from ISO is received, please check with the TC that the ballot can proceed.
2011-05-02 EMA: draft for // Enquiry received in ISO/CS (see e-mail of 2011-04-28 in dataservice).
- Draft52 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a test method for the determination of the resistance of protective clothing, gloves and footwear materials to permeation by potential hazardous liquid chemicals under the condition of continuous contact.
This test method is applicable to the assessment of protection against liquid chemicals that can be collected only by liquid or gaseous collecting media.
This test method is not adapted for the assessment of chemical mixtures, except for aqueous solutions.
This standard shall be used with the specifications given in the products standards (for examples EN 374 1 for gloves) where the following information shall be defined:
- any pre-conditioning;
- precise sampling (place, size, number);
- associated levels of performance.
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a test method for the determination of the resistance of protective clothing, gloves and footwear materials to permeation by potentially hazardous gaseous chemicals under the condition of continuous contact.
This test method is applicable to the assessment of protection against gazeous chemicals that can be collected only by liquid or gaseous collecting media.
This test method is not adapted for the assessment of gaseous chemical mixtures.
This test method describes the modifications to EN 16523 1 necessary to test against gaseous chemicals that can be collected by liquid or gaseous collecting media.
- Draft7 pagesEnglish languagesale 10% offe-Library read for1 day
- delete the last row of table 1 (reference to EN 14325, clause 4.14)
- add, at the end of clause 4.1, the following note: "If resistance to heat and flame is required, the chemical protective clothing should be tested and marked according to the appropriate standard." (taken from EN 14325, 4.14)
add in clause 6 (information) the warning phrase: "Flammable material. Keep away from fire"
- Draft4 pagesEnglish languagesale 10% offe-Library read for1 day
- delete the last row of table 1 (reference to EN 14325, clause 4.14)
- add, at the end of clause 4.1, the following note: "If resistance to heat and flame is required, the chemical protective clothing should be tested and marked according to the appropriate standard." (taken from EN 14325, 4.14)
add in clause 7 (information) the warning phrase: "Flammable material. Keep away from fire"
- Draft4 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and test methods for protective clothing, ventilated by an independent supply of air from an uncontaminated source, protecting the body and the respiratory system of the wearer against solid airborne particles including radioactive contamination. This kind of protective clothing can be provided with an emergency breathing facility.
This European Standard does not apply for the protection against ionizing radiation and the protection of patients against contamination with radioactive substances by diagnostic and/or therapeutic measures.
If additional protection against chemicals is required, reference should be made to the relevant standard and/or CEN/TR 15419.
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer for ventilated and non-ventilated gas-tight chemical protective suits.
It specifies full body personal protective ensembles to be worn for protection against solid, liquid and gaseous chemicals, including liquid and solid aerosols.
This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosive, infective agents. This type of equipment is not intended for total immersion in liquids.
The seams, joins and assemblages attaching the accessories are included within the scope of this standard. This standard specifies only supplementary requirements for components. The basic performance criteria for the components gloves, boots or respiratory protective equipment are given in other European Standards.
Particulate protection is limited to physical penetration of the particulates only.
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
TC origin: addition of the list with the main technical changes in the Foreword and modification to Table 1 (SV on 2016-05-30)
- Corrigendum4 pagesEnglish languagesale 10% offe-Library read for1 day
2014-06-04 GVN: Draft for // enq received at ISO/CS (see ISO notification in dataservice on 2014-06-03).
- Amendment9 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and test methods for protective clothing, ventilated by an independent supply of air from an uncontaminated source, protecting the body and the respiratory system of the wearer against solid airborne particles including radioactive contamination. This kind of protective clothing can be provided with an emergency breathing facility.
This European Standard does not apply for the protection against ionizing radiation and the protection of patients against contamination with radioactive substances by diagnostic and/or therapeutic measures.
If additional protection against chemicals is required, reference should be made to the relevant standard and/or CEN/TR 15419.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the minimum requirements, test methods, marking and information supplied by the manufacturer for ventilated and non-ventilated gas-tight chemical protective suits.
It specifies full body personal protective ensembles to be worn for protection against solid, liquid and gaseous chemicals, including liquid and solid aerosols.
This standard does not establish minimum criteria for protection for non-chemical hazards, e.g. radiological, fire, heat, explosive, infective agents. This type of equipment is not intended for total immersion in liquids.
The seams, joins and assemblages attaching the accessories are included within the scope of this standard. This standard specifies only supplementary requirements for components. The basic performance criteria for the components gloves, boots or respiratory protective equipment are given in other European Standards.
Particulate protection is limited to physical penetration of the particulates only.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 17491-4:2008 specifies methods for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity:
Method A: low-level spray test. This is applicable to clothing that covers the full body surface and which is intended to be worn when there is a potential risk of exposure to small quantities of spray or accidental low volume splashes of a liquid chemical.
Method B: high level spray test This is applicable to clothing with spray-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment, which covers the full body surface and which is intended to be worn when there is a risk of exposure to sprayed particles of liquid.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This technical report is primarily intended for users, specifiers and others with responsibility for the procurement and provision of chemical protective clothing. It is also intended to be used by manufacturers in their dialogue with the users of PPE.
This technical report is intended to clarify the inter-relationship of the set of standards, developed by CEN/TC 162 WG 3, and to explain the main ideas behind these standards. This set of standards has been developed in support of the European legislation on PPE and is currently used as a major technical tool for the assessment and certification of CPC before it is put on the European market.
These guidelines are intended to assist users and specifiers in selecting the correct type of CPC for the task to be performed, and to help them ensure it is used according to the manufacturer's instructions to provide adequate protection during its entire lifetime. Lifetime and effectiveness of protective clothing depend largely on care and maintenance. When cleaning, disinfection and end-of-life disposal are considered the environmental impact should also be taken into account.
This technical report does not address chemical nuisance factors without potential impact on a person's health and safety, e.g. smell.
- Technical report30 pagesEnglish languagesale 10% offe-Library read for1 day
CMC - Normative reference to EN 369 to be replaced by EN ISO 6529 and update reference in B.2.10 accordingly
- Corrigendum2 pagesEnglish, French and German languagesale 10% offe-Library read for1 day
This European Standard specifies the performance classification and test methods for chemical protective clothing material and seams, joins and assemblages. This is a reference standard to which other chemical protective clothing performance standards may refer in whole or in part.
NOTE Whilst these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the user (specifier) and the chemical protective clothing manufacturer or supplier liase to establish the correct performance level for the intended task. For this purpose a risk analysis could be useful.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day