EN 14605:2005+A1:2009

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.>@Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzanzüge mit flüssigkeitsdichten (Typ 3) oder spraydichten (Typ 4) Verbindungen zwischen den Teilen der Kleidung, einschließlich der Kleidungsstücke, die nur einen Schutz für Teile des Körpers gewähren (Typen PB [3] und PB [4])Vêtements de protection contre les produits chimiques liquides - Exigences relatives aux vêtements dont les éléments de liaison sont étanches au liquide (Type 3) ou aux pulvérisations (Type 4), y compris les articles d'habillement protégeant seulement certaines parties du corps (Types PB (3) et PB (4))Protective clothing against liquid chemicals - performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])13.340.10Varovalna oblekaProtective clothingICS:Ta slovenski standard je istoveten z:EN 14605:2005+A1:2009SIST EN 14605:2005+A1:2009en,fr,de01-julij-2009SIST EN 14605:2005+A1:2009SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14605:2005+A1
May 2009 ICS 13.340.10 Supersedes EN 14605:2005English Version
Protective clothing against liquid chemicals - performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])
Vêtements de protection contre les produits chimiques liquides - Exigences relatives aux vêtements dont les éléments de liaison sont étanches au liquide (Type 3) ou aux pulvérisations (Type 4), y compris les articles d'habillement protégeant seulement certaines parties du corps (Types PB (3) et PB (4))
Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzanzüge mit flüssigkeitsdichten (Typ 3) oder spraydichten (Typ 4) Verbindungen zwischen den Teilen der Kleidung, einschließlich der Kleidungsstücke, die nur einen Schutz für Teile des Körpers gewähren (Typen PB [3] und PB [4]) This European Standard was approved by CEN on 14 February 2005 and includes Amendment 1 approved by CEN on 5 April 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14605:2005+A1:2009: ESIST EN 14605:2005+A1:2009

Relationship between this
European
Standard and the Essential Requirements
of EU Directive 89/686/EEC . 11 Bibliography . 12
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;  Full-body protective clothing with spray-tight connections between different parts of the clothing (Type 4: spray-tight clothing) and, if applicable, spray-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards.
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;  Partial body protection garments offering protection to specific parts of the body against permeation of chemical liquids. Examples of such garments are e.g. laboratory coats, jackets, trousers, aprons, sleeves, hoods (not air-supplied) etc. As partial body protection leaves some parts of the body unprotected this document specifies only the performance requirements for the clothing material and the seams. NOTE Partial body chemical protective garments which offer only protection against penetration of chemical liquids are within the scope of EN 13034 (Type PB [6] clothing). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 340:2003, Protective clothing — General requirements !deleted text" EN 12941:1998, Respiratory protective devices - Powered filtering devices incorporating a helmet or a hood - Requirements, testing, marking !EN 14325:2004", Protective clothing against chemicals — Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages !deleted text" EN 31092, Textiles — Determination of physiological properties — Measurement of thermal and water-vapour resistance under steady-state conditions (sweating guarded - hotplate test) (ISO 11092:1993) !EN ISO 3758, Textiles – Care labelling code using symbols (ISO 3758:2005)" CEN ISO/TR 11610:2004, Protective clothing - Vocabulary (ISO/TR 11610:2004) !EN ISO 17491-3, Protective clothing – Test methods for clothing providing protection against chemicals – Part 3: Determination of resistance to penetration by a jet of liquid (jet test) (ISO 17491-3:2008)" !EN ISO 17491-4, Protective clothing – Test methods for clothing providing protection against chemicals – Part 4: Determination of resistance to penetration by a spray of liquid (spray test) (ISO 17491-4:2008)" SIST EN 14605:2005+A1:2009

!!!!EN 14325:2004""""Performance requirement 4.4 abrasion resistance 4.5 flex cracking resistance 4.6 a flex cracking resistance at –30 °C 4.7 tear resistance (trapezoidal) 4.9 tensile strength 4.10 puncture resistance 4.11 resistance to permeation of liquids !deleted text" a Only applicable to clothing intended for use at very low temperatures.
NOTE 1 Chemical protective clothing material, for which a test method in Table 1 does not provide a clear measurement end-point, should be marked "not applicable" in the test report and in the instructions for use. The reason why the test could not be completed should be indicated, e.g. where the elasticity of the specimen prevents to determine an end-point in the puncture resistance test. NOTE 2 Materials should be as light and as flexible as possible in order to ensure wearer comfort as well as providing effective protection. Material properties are only one element for the determination of wearer comfort of protective clothing. Design features of the clothing may even have a more important influence on wearer comfort than material properties. SIST EN 14605:2005+A1:2009

Type PB [4] clothing Performance requirement Reference resistance to permeation of liquids b !EN 14325:2004", 4.11 resistance to penetration by liquids c !EN ISO 17491-3" or
!EN ISO 17491-4" seam strength !EN 14325:2004", 5.5 a Seams, joins and assemblages of Type PB [3] clothing shall be tested to the jet test (!EN ISO 17491-3"). b Applicable only to seam
...