This document specifies characteristics and performances of plastic and rubber sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles where the waterproofing is fully bonded to the concrete deck and fully bonded to the asphalt overlay.
This document does not cover concrete surfaces trafficable by vehicles where the waterproofing is not fully bonded to the concrete and/or not fully bonded to an overlay.
This document also states the test methods used for verifying the characteristics and gives rules for the assessment and verification of consistency of performance of the product.

  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a procedure for artificial ageing of flexible underlays which are used under discontinuous roof coverings. This is achieved by exposing test samples to UV-radiation, elevated temperature in combination with high relative humidity and elevated temperature in combination with accelerated air-speed.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies instructions for mounting and fixing for reaction to fire testing of factory-made underlays for discontinuous roof coverings and walls and contains provisions for direct and extended application rules.
These mounting and fixing procedures are not intended to be used for flat roofed waterproofing applications.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Experience with testing in accordance with EN 13948 has shown that flexible sheets for waterproofing with different thicknesses, different colours, different formulations, different surface finishing, and different internal fabrics, amongst others, have passed the test successfully.
This document expresses the extrapolation rules of the results of root resistance testing in accordance with EN 13948 for roof waterproofing sheets manufactured in accordance with EN 13707:2004+A2:2009, and EN 13956:2012.
Experience with testing in accordance to EN 13948 has shown that the main critical points are represented by the joints. If joints are done in a proper way, it will avoid the penetration of roots during the test.

  • Technical specification
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the general rules how to select the samples of correctly stored and handled samples of uninstalled bitumen, plastic or rubber sheets for waterproofing. It also specifies the procedures to be followed before the test piece is cut from the sample.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the test method to determine the resistance to wind load of the roof build-up system with the waterproofing system bonded to the substrate.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives guidance for the design of a roof waterproofing system mechanically fastened to the structural deck in relation to wind load resistance.
This document is intended to be used together with EN 16002 and the relevant clauses of EAD-030351-00-0402-2019.
This guideline does not include the seperate fastening requirements of the insulation boards, the securement to upstands, perimeter fastening, flashings or other roof details.

  • Technical specification
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC origin: last two paragraphs replaced by new one in 8.4 and additional hyphen in Clause 12

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is one of a series of documents applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles.
This document specifies:
-   the composition, the characteristics and the preparation procedure of the base specimen concrete slabs;
-   the composition, the characteristics and the preparation procedure of different bituminous mixtures for the asphalt layer;
-   the rules for the preparation of specimens.
This document outlines the specimen preparation for tests on the waterproofing systems which are referred to in the different test standards.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing.
The assessment is limited to the performance of the mechanically fastened flexible sheets only. The test method does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard gives a calculation method of the Solar Reflectance Index (SRI) and the determination of solar reflectivity and thermal emissivity for waterproofing flexible sheets for roofs with a slope smaller than 10°.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test for puncture by impact on sheets for roof waterproofing. Mechanical stress on waterproofing sheets ranges from static long-term loads to dynamic short-term loads. This method represents the dynamic category of load where puncture may be caused by impact.
This European Standard may also be applied for other purposes of waterproofing.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable to bitumen sheets intended for use with a layer of mastic asphalt.
This European Standard specifies a test method for the evaluation of the resistance of bitumen sheets to the rising of the bitumen compound at the application of mastic asphalt in a non-floating manner.
Note   This European Standard could also be used for bitumen sheets intended for use with other asphalt types as a protection layer.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method for the evaluation of the resistance to impact puncturing of a sheet or sheet system.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test method for the evaluation of the compatibility of the waterproofing system applied to a concrete surface and covered with an asphalt layer. The complete system is exposed to an accelerated heat conditioning followed by a determination of the shear strength properties before and after heat conditioning.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test method for the determination of water absorption in reinforced bitumen sheets which could influence the functional behaviour of these sheets.
NOTE   It is primarily the reinforcement's ability to absorb water which is examined by this test.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method for the evaluation of the resistance of a bitumen sheet to compaction of an asphalt layer.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document is one of a series of standards applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles.
This document specifies a test method for the evaluation of the shear strength properties of the waterproofing sheet system applied to a concrete surface and with an asphalt layer.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to the apparatus and the test procedure used for the determination of the adhesion of granules to factory made bituminous sheets for roofing. It can also be used in other areas where it is relevant.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a test for puncture by static loading for roofing membranes. Mechanical stress on membranes varies from static long-term loads to dynamic short-term loads. This method represents the static category of load where the stress is applied over a period of time.
This European Standard may also be applied for waterproofing.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies the characteristics of flexible sheets for underlays for walls which are to be used in walls behind outside wall coverings in order to avoid penetration of wind and water from outside. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies the characteristics of flexible sheets for underlays which are to be used under roof covering of discontinuous roofs. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing.
This European Standard does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e.g. asphalt) directly applied at high temperature, specified by EN 14695.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Report is a guideline for the statistic approach for the definition of MLV/MDV within the declaration of values according to the product standards of CEN/TC 254 'Flexible sheets for waterproofing' (see Bibliography). Characteristics with classes (for example fire behaviour) or pass/fail criteria (for example UV exposure) are not covered by the statistical rules of this report.

  • Technical report
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the characteristics of flexible sheets of plastic or rubber intended for use as water vapour control layers for buildings and applies to both reinforced and unreinforced products. It specifies requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the resistance to peeling of joints between two adjacent sheets of the same plastic or rubber sheets for waterproofing.
This test method will be used mainly for testing the joints in mechanically fastened plastic or rubber sheets for waterproofing.
The peel strength characterises the optimum joint strength which can be reached for a membrane and a joint technique under laboratory conditions. On roofs the joint strength could be clearly reduced due to the non-optimal conditions (e.g. pressure, temperature, humidity, pollution, workmanship). The requirement for the joint technique at the site is to ensure a permanently tight joint.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the resistance of plastic and rubber sheets for waterproofing to cracking when exposed, under static tensile strain, to air containing a definite concentration of ozone and at a definite temperature without the effects of direct light.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for the determination of the behaviour of plastic and rubber sheets for waterproofing to folding after exposure at a low temperature.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies test methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the determination of flexibility of bitumen sheets at low temperatures. The test can be carried out on the upper or lower face of the sheet either at a predetermined temperature or successively at different temperature steps to determine the cold bending temperature which represents a limiting temperature. Therefore, the test can be used to confirm a minimum cold bending temperature for a product or to determine the specific cold bending temperature for the product e.g. to determine the change of these properties as a result of artificial ageing.
In the case of sheets with the same bituminous compound on both sides and where the reinforcement is placed in the cross section visually closer to the upper surface, the test is performed on the bottom face only.
If the upper surface is covered with a non woven (e.g. tissue, fleece etc.) or metal facing, the test is performed on the bottom side only.
If the sheet on the upper surface is covered with permanent light surface protection and where the reinforcement is placed in the cross section visually closer to the upper surface, the test is performed on the bottom side only.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail.
This European Standard may also be applied for waterproofing.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
NOTE   For typical materials and applications, see Annex E.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
This European Standard does not cover related products such as preformed cavity trays, coping and flashings.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the method to determine the emissivity of plastic, rubber and bitumen vapour control layers, underlays for walls and underlays for discontinuous roofing.
It also defines a conditioning procedure for these product families in order to quantify the sensitivity of emissivity to humidity and temperature.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies characteristics and performance of reinforced bitumen sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete where the waterproofing system is bonded to the concrete deck and overlaid by asphalt. The standard also specifies the test methods used for verifying the characteristics and performance.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the determination of flow resistance of bitumen sheets at elevated temperature. The test is carried out at a specified temperature or consecutively at different temperatures in order to determine the flow resistance limit. Therefore, the test can be used to provide proof of the flow resistance required for a product or to determine the flow resistance limit specific to the product e.g. in order to establish the change in this behaviour as a result of artificial ageing.
The test is not applicable to bitumen sheets without reinforcement.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing.
NOTE   The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standad specifies a method to test the resistance against water penetration of underlays for discontinuous roofing and for walls.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes a test method for determining the crack bridging ability of reinforced bitumen sheets used in waterproofing systems on concrete bridge decks and other areas of concrete trafficable by vehicles.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing, free from all external restraint, to liquid chemicals (including water), and methods for determining the changes in properties resulting from such exposure.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing free from all external restraint, to contact with bitumen at an elevated temperature and methods for determining the changes in properties resulting from such exposure.
The methods for determination of changes in properties are specified as follows:
a)   changes in mass directly after contact with bitumen;
b)   changes in physical properties after contact with bitumen.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a method to determine the resistance of roof waterproofing sheets to root penetration.
This European Standard relates exclusively to sheets. It is not possible to test a system comprising several different sheets.
This European Standard does not contain any evaluation of the sheet to be tested in respect of its environmental requirements.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as water vapour control layers for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as water vapour control layers for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the characteristics of flexible sheets of bitumen intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
This European Standard does not cover related products such as preformed cavity trays, coping and flashings.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as water vapour control layers for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day