CEN/TC 254/SC 2 - Synthetic sheets
Flexible sheets for waterproofing comosed largely of thermoplastic and elastomeric polymers.
Synthetic sheets
Flexible sheets for waterproofing comosed largely of thermoplastic and elastomeric polymers.
General Information
This document specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the characteristics of flexible sheets of plastic or rubber intended for use as water vapour control layers for buildings and applies to both reinforced and unreinforced products. It specifies requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for determining the resistance to peeling of joints between two adjacent sheets of the same plastic or rubber sheets for waterproofing.
This test method will be used mainly for testing the joints in mechanically fastened plastic or rubber sheets for waterproofing.
The peel strength characterises the optimum joint strength which can be reached for a membrane and a joint technique under laboratory conditions. On roofs the joint strength could be clearly reduced due to the non-optimal conditions (e.g. pressure, temperature, humidity, pollution, workmanship). The requirement for the joint technique at the site is to ensure a permanently tight joint.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for the determination of the resistance of plastic and rubber sheets for waterproofing to cracking when exposed, under static tensile strain, to air containing a definite concentration of ozone and at a definite temperature without the effects of direct light.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for the determination of the behaviour of plastic and rubber sheets for waterproofing to folding after exposure at a low temperature.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies test methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail.
This European Standard may also be applied for waterproofing.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
NOTE For typical materials and applications, see Annex E.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
This European Standard does not cover related products such as preformed cavity trays, coping and flashings.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing.
NOTE The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing, free from all external restraint, to liquid chemicals (including water), and methods for determining the changes in properties resulting from such exposure.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing free from all external restraint, to contact with bitumen at an elevated temperature and methods for determining the changes in properties resulting from such exposure.
The methods for determination of changes in properties are specified as follows:
a) changes in mass directly after contact with bitumen;
b) changes in physical properties after contact with bitumen.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies methods for the determination of the visible defects of thermoplastic and elastomeric sheets for waterproofing, which could influence the functional behaviour of these sheets.
- Standard5 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies a method for the determination of the dimensional variations after heating of thermoplastic and elastomeric roofing and sealing sheets. This is a test standard in support of the standardization of building products in the field of flexible sheets for waterproofing.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies methods for the determination of length, width, straightness and flatness of thermoplastic and elastomeric sheets for roof waterproofing.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
Plastic waterproofing sheets generate plastic waste at different stages: production, construction process, use and end of life.
This document defines the origin of recyclate made from pre-consumer material and post-consumer material as it is used in new products. These new products can be plastic waterproofing sheets, other sheets, other construction products or other products.
It specifies terms and definitions.
It gives guidance for assessing the recyclates intended for use in the production of new products.
NOTE This document is suitable for products with similar content like: swimming pool membranes, geosynthetic barriers, garden ponds, walk-ways, protection membranes, prefabricated pieces. The design for recycling of packaging, including the recycling itself, is defined in the CEN TC 261 Packaging.
- Draft19 pagesEnglish languagesale 10% offe-Library read for1 day
The scope of this amendment includes:
- the introduction of CPR requirements (e.g. Annex ZA, clause 6)
- removal of Product Data Sheets descriptions (e.g. clause 7 and Annex D)
- reference to CEN/TR 16625 for MLV/MDV
- correction of minor editorial issues.
- Draft18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies test methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for the determination of the resistance of elastomeric and thermoplastic elastomeric sheets for waterproofing to cracking when exposed, under static tensile strain, to air containing a definite concentration of ozone and at a definite temperature in circumstances that exclude the effects of direct light.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies a method for the determination of the behaviour of thermoplastic and elastomeric roofing and sealing sheets when submitted to folding after exposure at a low temperature. This is a test standard in support of the standardization of building products in the field of flexible sheets for waterproofing.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Modification to Table A.1
- Corrigendum2 pagesEnglish, French and German languagesale 10% offe-Library read for1 day
This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
NOTE For typical materials and applications, see Annex E.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies two methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing: Method A based on EN/ISO 1421, is the preferred method which should be used for all materials. If method A is not suited to the material, i.e. the material does not rupture, method B based on ISO 37 can then be used to determine tensile properties.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing. NOTE The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies methods for the determination of the thickness and the mass per unit area of plastic and rubber sheets for roof waterproofing.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method of exposing test specimens of thermoplastic and elastomeric sheets for waterproofing, free from all external restraint, to liquid chemicals (including water), and methods for determining the changes in properties resulting from such exposure. Only testing by immersion of the entire surface of the test specimen is considered.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a method for determining the resistance to peeling of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing. This test method will be used mainly for testing the joints in mechanically fastened plastic or rubber sheets for roof waterproofing. NOTE The peeling characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day