SIST EN ISO 17652-1:2003

SLOVENSKI STANDARD
01-december-2003
Varjenje - Preskus osnovnih premazov v zvezi z varjenjem in sorodnimi postopki -
1. del: Splošne zahteve (ISO 17652-1:2003)
Welding - Test for shop primers in relation to welding and allied processes - Part 1:
General requirements (ISO 17652-1:2003)
Schweißen - Prüfung von Fertigungsbeschichtungen für das Schweißen und für
verwandte Prozesse - Teil 1: Allgemeine Anforderungen (ISO 17652-1:2003)
Soudage - Essai sur peintures primaires en relation avec le soudage et les techniques
connexes - Partie 1: Exigences générales (ISO 17652-1:2003)
Ta slovenski standard je istoveten z: EN ISO 17652-1:2003
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 17652-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2003
ICS 25.160.10
English version
Welding - Test for shop primers in relation to welding and allied
processes - Part 1: General requirements (ISO 17652-1:2003)
Soudage - Essai sur peintures primaires en relation avec le Schweißen - Prüfung von Fertigungsbeschichtungen für
soudage et les techniques connexes - Partie 1: Exigences das Schweißen und für verwandte Prozesse - Teil 1:
générales (ISO 17652-1:2003) Allgemeine Anforderungen (ISO 17652-1:2003)
This European Standard was approved by CEN on 2 January 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17652-1:2003 E
worldwide for CEN national Members.

Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Guidance on application .5
5 Health, safety and environment.6
Bibliography .7
Foreword
This document (EN ISO 17652-1:2003) has been prepared by Technical Committee CEN/TC 121 "Welding", the
secretariat of which is held by DS, in collaboration with Technical Committee ISO/TC 44 “Welding and allied
processes”.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by November 2003, and conflicting national standards shall be withdrawn at the latest
by November 2003.
EN ISO 17652 consists of the following parts, under the general title: Welding – Test for shop primers in relation to
welding and allied processes:
- Part 1: General requirements
- Part 2: Welding properties of shop primers
- Part 3: Thermal cutting
- Part 4: Emission of fumes and gases
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
1 Scope
This part of this European Standard specifies standardised conditions for an assessment of shop primers on the
weldability of steel materials. The standard is intended to be used for assessment of shop primers by:
 testing by the suppliers during development of new shop primers;
 testing by the suppliers during production as part of a quality control scheme;
 declaration of the properties of shop primers by suppliers;
 use as a reference in contracts between suppliers and customers for deliveries of shop primers;
 acceptance testing of shop primers by customers.
The standard can also be used for comparisons between different shop primers using the welding procedure
appropriate for the task, or between the different welding procedures using a specific shop primer.
For guidance on application see clause 4.
2 Normative references
This European Standard incorporates by dated or un
...