SIST-TP CEN ISO/TR 15608:2006

SLOVENSKI STANDARD
SIST-TP CEN ISO/TR 15608:2006
01-marec-2006
1DGRPHãþD
SIST CR ISO 15608:2001
9DUMHQMH±6PHUQLFH]DUD]YUãþDQMHNRYLQVNLKPDWHULDORYYVNXSLQH,6275

Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2005)
Schweißen - Richlinien für eine Gruppeneinteilung von metallischen Werkstoffen
(ISO/TR 15608:2005)
Soudage - Lignes directrices pour un systeme de groupement des matériaux métalliques
(ISO/TR 15608:2005)
Ta slovenski standard je istoveten z: CEN ISO/TR 15608:2005
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST-TP CEN ISO/TR 15608:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN ISO/TR 15608:2006

---------------------- Page: 2 ----------------------

SIST-TP CEN ISO/TR 15608:2006
TECHNICAL REPORT
CEN ISO/TR 15608
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
October 2005
ICS 25.160.01 Supersedes CR ISO 15608:2000
English Version
Welding - Guidelines for a metallic materials grouping system
(ISO/TR 15608:2005)
Soudage - Lignes directrices pour un système de Schweißen - Richlinien für eine Gruppeneinteilung von
groupement des matériaux métalliques (ISO/TR metallischen Werkstoffen (ISO/TR 15608:2005)
15608:2005)
This Technical Report was approved by CEN on 4 July 2005. It has been drawn up by the Technical Committee CEN/TC 121.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TR 15608:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN ISO/TR 15608:2006

CEN ISO/TR 15608:2005 (E)





Foreword


This document (CEN ISO/TR 15608:2005) has been prepared by Technical Committee
CEN/TC 121, "Welding" the secretariat of which is held by DIN, in collaboration with Technical
Committee ISO/TC 44 "Welding and allied processes".

This document supersedes CR ISO 15608:2000.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to announce this CEN Technical Specification: Austria,
Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


2

---------------------- Page: 4 ----------------------

SIST-TP CEN ISO/TR 15608:2006


TECHNICAL ISO/TR
REPORT 15608
Second edition
2005-10-15

Welding — Guidelines for a metallic
materials grouping system
Soudage — Lignes directrices pour un système de groupement des
matériaux métalliques




Reference number
ISO/TR 15608:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST-TP CEN ISO/TR 15608:2006
ISO/TR 15608:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST-TP CEN ISO/TR 15608:2006
ISO/TR 15608:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope.1
2 Grouping system for steels .1
3 Grouping system for aluminium and aluminium alloys.4
4 Grouping system for copper and copper alloys.4
5 Grouping system for nickel and nickel alloys .5
6 Grouping system for titanium and titanium alloys.5
7 Grouping system for zirconium and zirconium alloys.6
8 Grouping system for cast iron .6


© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST-TP CEN ISO/TR 15608:2006
ISO/TR 15608:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that
which is normally published as an International Standard (“state of the art”, for example), it may decide by a
simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely
informative in nature and does not have to be reviewed until the data it provides are considered to be no
longer valid or useful.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 15608 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO/TR 15608:2000), which has been technically
revised.
iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST-TP CEN ISO/TR 15608:2006
ISO/TR 15608:2005(E)
Introduction
Requests for official interpretations of any aspect of this Technical Report should be directed to the Secretariat
of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can be found at
www.iso.org.
© ISO 2005 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST-TP CEN ISO/TR 15608:2006

---------------------- Page: 10 ----------------------

SIST-TP CEN ISO/TR 15608:2006
TECHNICAL REPORT ISO/TR 15608:2005(E)

Welding — Guidelines for a metallic materials grouping system
1 Scope
This Technical Report provides a uniform system for grouping of materials for welding purposes. It may also
apply to other purposes such as heat treatment, forming, non-destructive testing.
This Technical Report covers grouping systems for the following standardized materials:
 steel;
 alum
...