ISO 13617:2019
(Main)Ships and marine technology — Shipboard incinerators — Requirements
Ships and marine technology — Shipboard incinerators — Requirements
This document covers the design, manufacture, performance, operation, functioning and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during a ship's normal service (i.e. maintenance, operational, domestic and cargo-associated wastes). This document is applicable to incinerator plants with capabilities up to 4 000 kW per unit. This document is not applicable to systems on special incinerator ships, e.g. for burning industrial wastes such as chemicals, manufacturing residues, etc. It does not address the electrical supply to the unit, nor the foundation connections and stack connections. This document provides emission requirements in Annex A, location requirements in Annex B, and flue gas temperature requirements in Annex D. Recommendations for incinerators integrated with heat recovery units are given in Annex C. The activities associated with this document can involve hazardous materials, operations and equipment. It does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Navires et technologie maritime — Incinérateurs de bord pour navires — Exigences
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13617
Third edition
2019-08
Ships and marine technology —
Shipboard incinerators —
Requirements
Navires et technologie maritime — Incinérateurs de bord pour
navires — Exigences
Reference number
©
ISO 2019
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General design requirements . 4
4.1 Piping . 4
4.2 Rotating parts . 4
4.3 Insulation and cooling . 4
4.4 Corrosion . 4
4.5 Liquid waste incineration . 4
4.6 Combustion chamber . 4
4.7 Combustion pressure . 4
4.8 Charging solid waste . 5
4.9 Feeding system. 5
4.10 Ash removal . 5
4.11 Observation port . 5
4.12 Design temperature values . 5
4.13 Pre-purging and post-purging . 5
4.14 Mass fraction of oxygen in the discharge gases . 5
4.15 Warning plate(s) . 6
4.16 Instruction plate(s) . 6
4.17 Flue gas cooling . 6
5 Electrical requirements . 6
5.1 General requirements . 6
5.2 Disconnects . 6
5.3 Live parts . 6
5.4 Failure design . 6
5.5 Control-circuit connections . 6
5.6 Component voltage ratings . 6
5.7 Weather endurance . 7
5.8 Control device testing and acceptance . 7
5.9 Control-circuit design . 7
5.10 Overcurrent protection . 7
5.11 Motors. 7
5.12 Ignition systems . 7
5.13 Wiring . 7
5.14 Bonding . 8
6 Materials . 8
7 Operating controls . 8
7.1 Disconnect switch. 8
7.2 Emergency stop switch . 8
7.3 Control equipment failures . 8
7.3.1 General provisions. 8
7.3.2 Safety thermostat . 8
7.3.3 Flame failure/low oil pressure . 8
7.3.4 Loss of power condition . 9
7.4 Fuel-control valves. 9
7.5 Alarms and indicators . 9
7.6 Fire box cooling . 9
8 Other requirements . 9
8.1 Instruction and maintenance manual . 9
8.2 Operation while inclined .10
8.3 Energy source .10
8.4 Drip trays .10
9 Testing .10
9.1 Prototype testing .10
9.2 Factory testing .10
9.3 Installation tests .10
9.3.1 Flame safeguard system .10
9.3.2 Limit controls.10
9.3.3 Combustion controls .10
9.3.4 Programming controls .11
9.3.5 Fuel control valves .11
9.3.6 Low voltage controls .11
9.3.7 Switches .11
10 Certification .11
11 Marking .11
12 Quality assurance .11
Annex A (normative) Emission requirements for shipboard incinerators with capacities of
up to 4 000 kW on ships subject to MARPOL .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.