Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-5: Particular requirements for the termination of twin-ax cable for databus applications

Part 2-5 of this European Standard specifies detail requirements for hand crimping tools incorporating a system of multiple indentors for use with Databus contacts of electrical connectors and similar components. Two tools are covered, as follows: a tool for contacts with crimp barrel size 22 (tool reference EN 50109-2-5-001), see clause 5; a tool for contacts with crimp barrel size 20 (tool reference EN 50109-2-5-002), see clause 5. It includes requirements for crimped joints made with the tools

Handcrimpwerkzeuge - Werkzeuge für den Crimpanschluß von elektrischen Leitungen und Drähten für Niederfrequenz- und für Hochfrequenzanwendungen - Teil 2-5: Spezielle Anforderungen für den Anschluß von Kabeln mit zwei Innenleitern für Datenbusanwendungen

Outils de sertissage manuels - Outils pour sertir les câbles et fils électriques basse fréquence et radio-fréquence - Partie 2-5: Sortie de câble 'twin-ax' pour applications bus de données

Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-5: Particular requirements for the termination of twin-ax cable for databus application

General Information

Status
Published
Publication Date
21-Jun-1995
Withdrawal Date
14-Dec-1995
Technical Committee
CLC/TC 46X - Communication cables
Drafting Committee
CLC/SC 46XC - Multicore, Multipair and Quad Data communication cables
Parallel Committee
IEC/TC 46 - IEC_TC_46
Current Stage
6060 - Document made available - Publishing
Start Date
22-Jun-1995
Completion Date
22-Jun-1995
Ref Project
SIST EN 50109-2-5:1996 - Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications -- Part 2-5: Particular requirements for the termination of twin-ax cable for databus applications

Overview

EN 50109-2-5:1995 (adopted as SIST EN 50109-2-5:1996 by CLC) is a European standard that defines particular requirements for hand crimping tools used to terminate twin-ax cable for databus applications. The document covers hand-operated crimp tools that use a system of multiple indentors and specifies the two tool variants by crimp barrel size: size 22 (EN 50109-2-5-001) and size 20 (EN 50109-2-5-002). It also includes requirements for the resulting crimped joints produced with these tools.

Key topics and technical requirements

  • Scope of tools: Requirements for hand crimping tools designed specifically for twin-ax/databus contacts and similar connector components.
  • Tool variants: Detailed coverage of two reference designs-crimp barrel size 22 and crimp barrel size 20 (tool references EN 50109-2-5-001 and EN 50109-2-5-002).
  • Multiple indentor systems: Specification focuses on tools incorporating multiple indentors to form the crimp profile required by Databus contacts.
  • Crimped joint requirements: The standard sets acceptance criteria and characteristics that crimped joints must meet when produced using the specified tools (mechanical and assembly quality expectations).
  • Conformity and procurement: Practical dimensions for specifying compliant tools and joints in purchasing documentation and design specifications.

(Note: the standard text should be consulted for precise dimensions, testing methods and acceptance criteria.)

Applications

  • Termination of twin-ax cable in databus systems for low-frequency and radio-frequency applications.
  • Use in component assembly and harness manufacture where consistent, reliable crimped joints are required for signal integrity.
  • Suitable for tool manufacturers, connector/cable assemblers, quality and test engineers who need to ensure compatible tooling and repeatable crimps.

Who should use this standard

  • Tool designers and manufacturers developing hand crimping tools for databus connectors.
  • Cable-assembly shops and harness manufacturers procuring tools or specifying crimp quality.
  • Quality assurance and test laboratories that validate crimped joint performance.
  • Procurement and engineering teams writing technical specifications for databus interconnects.

Related standards

  • EN 50109 series (hand crimping tools for low- and radio-frequency applications) - EN 50109-2-5 is a part addressing twin-ax/databus terminations.
  • Connector and contact manufacturers’ datasheets and general crimping standards should be consulted alongside EN 50109-2-5 for full implementation.

Keywords: hand crimping tools, twin-ax cable, databus, crimp termination, EN 50109-2-5, crimp barrel size 22, crimp barrel size 20, multiple indentors, crimped joints.

Frequently Asked Questions

EN 50109-2-5:1995 is a standard published by CLC. Its full title is "Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-5: Particular requirements for the termination of twin-ax cable for databus applications". This standard covers: Part 2-5 of this European Standard specifies detail requirements for hand crimping tools incorporating a system of multiple indentors for use with Databus contacts of electrical connectors and similar components. Two tools are covered, as follows: a tool for contacts with crimp barrel size 22 (tool reference EN 50109-2-5-001), see clause 5; a tool for contacts with crimp barrel size 20 (tool reference EN 50109-2-5-002), see clause 5. It includes requirements for crimped joints made with the tools

Part 2-5 of this European Standard specifies detail requirements for hand crimping tools incorporating a system of multiple indentors for use with Databus contacts of electrical connectors and similar components. Two tools are covered, as follows: a tool for contacts with crimp barrel size 22 (tool reference EN 50109-2-5-001), see clause 5; a tool for contacts with crimp barrel size 20 (tool reference EN 50109-2-5-002), see clause 5. It includes requirements for crimped joints made with the tools

EN 50109-2-5:1995 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-1996
Hand crimping tools - Tools for the crimp termination of electric cables and wires
for low frequency and radio frequency applications - Part 2-5: Particular
requirements for the termination of twin-ax cable for databus application
Hand crimping tools - Tools for the crimp termination of electric cables and wires for low
frequency and radio frequency applications -- Part 2-5: Particular requirements for the
termination of twin-ax cable for databus applications
Handcrimpwerkzeuge - Werkzeuge für den Crimpanschluß von elektrischen Leitungen
und Drähten für Niederfrequenz- und für Hochfrequenzanwendungen -- Teil 2-5:
Spezielle Anforderungen für den Anschluß von Kabeln mit zwei Innenleitern für
Datenbusanwendungen
Outils de sertissage manuels - Outils pour sertir les câbles et fils électriques basse
fréquence et radio-fréquence -- Partie 2-5: Sortie de câble 'twin-ax' pour applications bus
de données
Ta slovenski standard je istoveten z: EN 50109-2-5:1995
ICS:
25.140.30 2URGMD]DURþQRXSRUDER Hand-operated tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

--
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...