EN ISO 1182:2020

SLOVENSKI STANDARD
01-september-2020
Nadomešča:
SIST EN ISO 1182:2011
Preskusi odziva proizvodov na ogenj - Preskus negorljivosti (ISO 1182:2020)
Reaction to fire tests for products - Non-combustibility test (ISO 1182:2020)
Prüfungen zum Brandverhalten von Produkten - Nichtbrennbarkeitsprüfung (ISO
1182:2020)
Essais de réaction au feu de produits - Essai d'incombustibilité (ISO 1182:2020)
Ta slovenski standard je istoveten z: EN ISO 1182:2020
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 1182
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 13.220.50 Supersedes EN ISO 1182:2010
English Version
Reaction to fire tests for products - Non-combustibility test
(ISO 1182:2020)
Essais de réaction au feu de produits - Essai Prüfungen zum Brandverhalten von Produkten -
d'incombustibilité (ISO 1182:2020) Nichtbrennbarkeitsprüfung (ISO 1182:2020)
This European Standard was approved by CEN on 1 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1182:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 1182:2020) has been prepared by Technical Committee ISO/TC 92 "Fire safety"
in collaboration with Technical Committee CEN/TC 127 “Fire safety in buildings” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2020, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1182:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1182:2020 has been approved by CEN as EN ISO 1182:2020 without any modification.

INTERNATIONAL ISO
STANDARD 1182
Sixth edition
2020-06
Reaction to fire tests for products —
Non-combustibility test
Essais de réaction au feu de produits — Essai d'incombustibilité
Reference number
ISO 1182:2020(E)
©
ISO 2020
ISO 1182:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 1182:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 2
5 Test specimen . 9
5.1 General . 9
5.2 Preparation . 9
5.3 Number .10
6 Conditioning .10
7 Test procedure .11
7.1 Test environment .11
7.2 Set-up procedure .11
7.2.1 Specimen holder .11
7.2.2 Thermocouple .11
7.2.3 Electricity supply .11
7.2.4 Furnace stabilization .12
7.3 Calibration procedure .12
7.3.1 Furnace wall temperature .12
7.3.2 Furnace temperature .14
7.3.3 Procedure frequency .16
7.4 Standard test procedure .16
7.5 Observations during test .17
8 Expression of results .17
8.1 Mass loss .17
8.2 Flaming .18
8.3 Temperature rise .18
9 Test report .18
Annex A (informative) Precision of test method .19
Annex B (informative) Typical designs of test apparatus .21
Annex C (normative) Thermocouples for additional measurements .24
Annex D (informative) Temperature recording .26
Bibliography .31
ISO 1182:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 92, Fire safety, Subcommittee SC 1,
Fire initiation and growth, in collaboration with the European Committee for Standardization (CE
...