EN ISO 1182:2010

SLOVENSKI STANDARD
01-januar-2011
1DGRPHãþD
SIST EN ISO 1182:2002
Preskusi odziva gradbenih proizvodov na ogenj - Preskus negorljivosti (ISO
1182:2010)
Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010)
Prüfungen zum Brandverhalten von Bauprodukten - Nichtbrennbarkeitsprüfung (ISO
1182:2010)
Essais de réaction au feu des produits de construction et de transport - Essai
d'incombustibilité (ISO 1182:2010)
Ta slovenski standard je istoveten z: EN ISO 1182:2010
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 1182
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2010
ICS 13.220.50 Supersedes EN ISO 1182:2002
English Version
Reaction to fire tests for products - Non-combustibility test (ISO
1182:2010)
Essais de réaction au feu de produits - Essai Prüfungen zum Brandverhalten von Bauprodukten -
d'incombustibilité (ISO 1182:2010) Nichtbrennbarkeitsprüfung (ISO 1182:2010)
This European Standard was approved by CEN on 19 April 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1182:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 1182:2010) has been prepared by Technical Committee ISO/TC 92 "Fire safety" in
collaboration with Technical Committee CEN/TC 127 “Fire safety in buildings” the secretariat of which is held
by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn
at the latest by November 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1182:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1182:2010 has been approved by CEN as a EN ISO 1182:2010 without any modification.

INTERNATIONAL ISO
STANDARD 1182
Fifth edition
2010-05-15
Reaction to fire tests for products —
Non-combustibility test
Essais de réaction au feu de produits — Essai
d'incombustibilité
Reference number
ISO 1182:2010(E)
©
ISO 2010
ISO 1182:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 1182:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Apparatus.2
4.1 General .2
4.2 Furnace, draught shield and stand.3
4.3 Specimen holder and insertion device.3
5 Test specimen.9
5.1 General .9
5.2 Preparation.9
5.3 Number .10
6 Conditioning .10
7 Test procedure.10
7.1 Test environment.10
7.2 Set-up procedure.11
7.3 Calibration procedure .12
7.4 Standard test procedure.16
7.5 Observations during test.17
8 Expression of results.17
8.1 Mass loss.17
8.2 Flaming.17
8.3 Temperature rise .18
9 Test report.18
Annex A (informative) Precision of test method.19
Annex B (informative) Typical designs of test apparatus.22
Annex C (normative) Thermocouples for additional measurements .26
Annex D (informative) Temperature recording .28
Bibliography.32

ISO 1182:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1182 was prepared by Technical Committee ISO/TC 92, Fire safety, Subcommittee SC 1, Fire initiation
and growth.
This fifth edition cancels and replaces the fourth edition (ISO 1182:2002), which has been technically revised.
iv © ISO 2010 – All rights reserved

ISO 1182:2010(E)
Introduction
This fire test has been developed for use by those responsible for the selection of construction products which,
whilst not completely inert, produce only a very limited amount of heat and flame when exposed to
temperatures of approximately 750 °C.
The limitation of the field of application to testing homogeneous products and substantial components of non-
homogeneous products was introduced because of problems in defining specifications for the specimens. The
design of the specimen of non-homogeneous products strongly influences the test results, which is the reason
non-homogeneous products cannot be tested to this International Standard.

INTERNATIONAL STANDARD ISO 1182:2010(E)

Reaction to fire tests for products — Non-combustibility test
SAFETY PRECAUTIONS — The attention of all persons concerned with managing and carrying out
this test is drawn to the fact that fire testing can be hazardous and that there is a possibility that toxic,
harmful smoke and gases can be evolved during the test. Operational hazards can also arise during
the testing of specimens and the disposal of test residues.
An assessment of all potential hazards and risks to health should be made and safety precautions
should be identified and provided. Written safety instructions should be issued. Appropriate training
should be given to relevant personnel. Laboratory personnel should ensure that they follow written
safety instructions at all times.
1 Scope
This International Standard specifies a method of test for determining the non-combustibility performance,
under specified conditions, of homogeneous products and substantial components of non-homogeneous
products.
Information on the precision of the test method is given in Annex A.
2 Normative references
The following referenced documents are indispen
...