EN ISO 3098-5:1997

SLOVENSKI STANDARD
SIST EN ISO 3098-5:1998
01-maj-1998
7HKQLþQDGRNXPHQWDFLMDL]GHONRY3LVDYDGHO5DþXQDOQLãNRSRGSUWR
NRQVWUXLUDQMH&$'SLVDYHODWLQVNHDEHFHGHãWHYLOLQR]QDN
Technical product documentation - Lettering - Part 5: CAD lettering of the Latin alphabet,
numerals and marks (ISO 3098-5:1997)
Technische Produktdokumentation - Schriften - Teil 5: CAD-Schrift des lateinischen
Alphabetes sowie der Ziffern und Zei chen (ISO 3098-5:1997)
Documentation technique de produits - Ecriture - Partie 5: Ecriture en conception
assistée par ordinateur de l'alphabet latin, des chiffres et des signes (ISO 3098-5:1997)
Ta slovenski standard je istoveten z: EN ISO 3098-5:1997
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
01.140.10 3LVDQMHLQSUHþUNRYDQMH Writing and transliteration
35.240.10 5DþXQDOQLãNRSRGSUWR Computer-aided design
VQRYDQMHQDþUWRYDQMH (CAD)
REOLNRYDQMH&$'
SIST EN ISO 3098-5:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3098-5:1998

---------------------- Page: 2 ----------------------

SIST EN ISO 3098-5:1998

---------------------- Page: 3 ----------------------

SIST EN ISO 3098-5:1998

---------------------- Page: 4 ----------------------

SIST EN ISO 3098-5:1998
INTERNATIONAL ISO
STANDARD 3098-5
First edition
1997-12-15
Technical product documentation —
Lettering —
Part 5:
CAD lettering of the Latin alphabet, numerals
and marks
Documentation technique de produits — Écriture —
Partie 5: Écriture en conception assistée par ordinateur de l'alphabet latin,
des chiffres et des signes
Reference number
A
ISO 3098-5:1997(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 3098-5:1998
ISO 3098-5:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 3098-5 was prepared by Technical Committee
ISO/TC 10, Technical drawings, product definition and related
documentation, Subcommittee SC 1, Basic conventions.
ISO 3098 consists of the following parts, under the general title Technical
product documentation — Lettering:
— Part 0: General requirements
— Part 1: Currently used characters
— Part 2: Greek characters
— Part 3: Diacritical and particular marks for the Latin alphabet
— Part 4: Cyrillic characters
— Part 5: CAD lettering of the Latin alphabet, numerals and marks
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 3098-5:1998
©
INTERNATIONAL STANDARD  ISO ISO 3098-5:1997(E)
Technical product documentation — Lettering —
Part 5:
CAD lettering of the Latin alphabet, numerals and marks
1  Scope
This part of ISO 3098 specifies the general requirements for computer-aided design and draughting (CADD)
lettering, in accordance with all other parts of this International Standard, to be used in technical product
documentation (in particular on technical drawings).
It includes basic conventions as well as rules for the application of CAD lettering using the techniques of numerically
controlled lettering and draughting systems.
2  Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of
ISO 3098. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of ISO 3098 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid
International Standards.
ISO 3098-0:1997, Technical product documentation
...