EN ISO 10140-1:2021

SLOVENSKI STANDARD
01-julij-2021
Nadomešča:
SIST EN ISO 10140-1:2016
Akustika - Laboratorijsko merjenje zvočne izolirnosti gradbenih elementov - 1. del:
Pravila uporabe za določene proizvode (ISO 10140-1:2021)
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1:
Application rules for specific products (ISO 10140-1:2021)
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1:
Anwendungsregeln für bestimmte Produkte (ISO 10140-1:2021)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de
construction - Partie 1: Règles d'application pour produits particuliers (ISO 10140-
1:2021)
Ta slovenski standard je istoveten z: EN ISO 10140-1:2021
ICS:
17.140.01 Akustična merjenja in Acoustic measurements and
blaženje hrupa na splošno noise abatement in general
91.060.01 Stavbni elementi na splošno Elements of buildings in
general
91.120.20 Akustika v stavbah. Zvočna Acoustics in building. Sound
izolacija insulation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10140-1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2021
EUROPÄISCHE NORM
ICS 91.120.20 Supersedes EN ISO 10140-1:2016
English Version
Acoustics - Laboratory measurement of sound insulation
of building elements - Part 1: Application rules for specific
products (ISO 10140-1:2021)
Acoustique - Mesurage en laboratoire de l'isolation Akustik - Messung der Schalldämmung von Bauteilen
acoustique des éléments de construction - Partie 1: im Prüfstand - Teil 1: Anwendungsregeln für
Règles d'application pour produits particuliers (ISO bestimmte Produkte (ISO 10140-1:2021)
10140-1:2021)
This European Standard was approved by CEN on 1 May 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10140-1:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10140-1:2021) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by November 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10140-1:2016.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 10140-1:2021 has been approved by CEN as EN ISO 10140-1:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 10140-1
Third edition
2021-05
Acoustics — Laboratory measurement
of sound insulation of building
elements —
Part 1:
Application rules for specific products
Acoustique — Mesurage en laboratoire de l'isolation acoustique des
éléments de construction —
Partie 1: Règles d'application pour produits particuliers
Reference number
ISO 10140-1:2021(E)
©
ISO 2021
ISO 10140-1:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

ISO 10140-1:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 2
5 Structure of application rules for specific products . 2
Annex A (normative) Walls — Airborne sound insulation . 4
Annex B (normative) Doors — Airborne sound insulation . 6
Annex C (normative) Windows — Airborne sound insulation . 7
Annex D (normative) Glazing — Airborne sound insulation . 9
Annex E (normative) Small technical elements — Airborne sound insulation.16
Annex F (normative) Floors — Airborne and impact sound insulation .20
Annex G (normative) Acoustical linings — Improvement of airborne sound insulation .21
Annex H (normative) Floor coverings — Improvement of impact sound insulation .23
Annex I (normative) Shutters — Airborne sound insulation .32
Annex J (normative) Joints filled with fillers or seals — Sound reduction index .37
Annex K (normative) Roofs, roof/ceiling systems, roof windows/skylights and rooflights —
Rainfall sound . .48
Bibliography .53
ISO 10140-1:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2,
Building acoustics, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 126, Acoustic properties of building elements and of buildings, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 10140-1:2016), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— all references in the text have been updated;
— in Clause 2, the normative references have been updated;
— D.4.2.1 regarding reference IGUs has been edited;
— former Clause G.6, "Additional information", has been removed;
— H.6.2.2 has been edited;
— in Annex K, rooflights have been added.
A list of all parts in the ISO 10140 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

ISO 10140-1:2021(E)
Introduction
ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements
(see Table 1).
This document specifies the application rules for specific elements and products, including specific
requirements for the preparation and mounting of the test elements, and for the operating and test
conditions. ISO 10140-2 and ISO 10140-3 contain the general procedures for airborne and impact sound
insulation measurements, respectively, and refer to ISO 10140-4 and ISO 10140-5 where appropriate.
For elements and products without a specific application rule described in this document, it is possible
to apply ISO 10140-2 and ISO 10140-3. ISO 10140-4 contains basic measurement techniques and
processes. ISO 10140-5 contains the requirements for test facilities and equipment. For the structure of
ISO 10140 (all parts), see Table 1.
ISO 10140 (all parts) was developed to improve the layout for laboratory measurements, ensure
consistency and simplify future changes and additions regarding mounting conditions of test elements
in laboratory and field measurements. ISO 10140 (all parts) aims at presenting a well-written and
arranged format for laboratory measurements.
This document is planned to be updated with application rules for other products.
Table 1 — Structure and contents of ISO 10140 (all parts)
Relevant
part of Main purpose, contents and use Detailed content
ISO 10140
ISO 10140-1 It indicates the appropriate test procedure Appropriat
...